Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0262514 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) U

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION





JUNCTION CONNECTOR


a.

No. 1 CAN Junction Connector

C348056C01
3.323,0.552 3.875,0.875 0.552,0.323 4.354,1.385 4.667,0.917 4.667,0.917 4.917,0.917 true 4.344,1.594 4.667,2 4.667,2 4.917,2 true 4.167,1.417 4.563,0.667 4.563,0.667 4.813,0.667 true 4.167,1.583 4.583,2.24 4.583,2.24 4.833,2.24 true 3.99,1.396 4.406,0.396 4.406,0.396 4.656,0.396 true 3.948,1.583 4.448,2.49 4.448,2.49 4.698,2.49 true 2.615,1.396 2.323,0.917 2.323,0.917 2.073,0.917 true 2.823,1.385 2.469,0.698 2.469,0.698 2.219,0.698 true 3.021,1.385 2.635,0.5 2.635,0.5 2.385,0.5 true 3.375,1.385 2.896,0.271 2.896,0.271 2.646,0.271 true 2.635,1.583 2.333,1.979 2.333,1.979 2.083,1.979 true 2.844,1.573 2.438,2.219 2.438,2.219 2.188,2.219 true 3.031,1.583 2.552,2.438 2.552,2.438 2.302,2.438 true 3.385,1.583 2.74,2.646 2.74,2.646 2.49,2.646 true 3.792,1.406 4.323,0.177 4.323,0.177 4.573,0.177 true 3.781,1.573 4.354,2.677 4.354,2.677 4.604,2.677 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 3.469,0.635 3.927,0.833 0.458,0.198 10 false G67 1.479,0.833 2.396,1.031 0.917,0.198 10 false CANH*b 1.625,0.594 2.542,0.792 0.917,0.198 10 false CANH*c 1.792,0.396 2.708,0.594 0.917,0.198 10 false CANH*d 2.083,0.167 3,0.365 0.917,0.198 10 false CANH*e 4.594,0.094 5.51,0.292 0.917,0.198 10 false CANH*f 4.698,0.313 5.615,0.51 0.917,0.198 10 false CANH*g 4.979,0.833 5.896,1.031 0.917,0.198 10 false CANH*i 1.51,1.875 2.427,2.073 0.917,0.198 10 false CANL*b 1.635,2.115 2.552,2.313 0.917,0.198 10 false CANL*c 1.76,2.333 2.677,2.531 0.917,0.198 10 false CANL*d 1.958,2.552 2.875,2.75 0.917,0.198 10 false CANL*e 4.646,2.594 5.563,2.792 0.917,0.198 10 false CANL*f 4.75,2.406 5.667,2.604 0.917,0.198 10 false CANL*g 4.958,1.927 5.875,2.125 0.917,0.198 10 false CANL*i 4.854,0.594 5.771,0.792 0.917,0.198 10 false CANH*h 4.885,2.167 5.802,2.365 0.917,0.198 10 false CANL*h
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b for Brake Actuator Assembly (Skid Control ECU)
*c for Airbag Sensor Assembly *d for Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
*e for Combination Meter Assembly *f for No. 2 CAN Junction Connector
*g for Engine Stop and Start ECU (w/ Stop and Start System) *h for Headlight Leveling ECU Assembly (for LED Headlight or w/ Headlight Cleaner System)
*i for Central Gateway ECU (Network Gateway ECU) - -


No. 1 CAN Junction Connector Wiring Color Connect to

*1: w/ Stop and Start System

*2: for LED Headlight or w/ Headlight Cleaner System

G67-1 (CANH) B Brake actuator assembly (skid control ECU)
G67-11 (CANL) W
G67-2 (CANH) Y Airbag sensor assembly
G67-12 (CANL) W
G67-3 (CANH) BE Spiral with sensor cable sub-assembly (steering angle sensor)
G67-13 (CANL) W
G67-5 (CANH) SB Combination meter assembly
G67-15 (CANL) W
G67-6 (CANH) LG No. 2 CAN junction connector
G67-16 (CANL) W
G67-7 (CANH) P Engine stop and start ECU*1
G67-17 (CANL) W
G67-8 (CANH) V Headlight leveling ECU assembly*2
G67-18 (CANL) W
G67-9 (CANH) R Central gateway ECU (network gateway ECU)
G67-19 (CANL) W


b.

No. 2 CAN Junction Connector

C348056C02
3.323,0.552 3.875,0.875 0.552,0.323 4.5,1.385 4.813,0.917 4.813,0.917 5.063,0.917 true 4.5,1.583 4.823,1.99 4.823,1.99 5.073,1.99 true 3.01,1.396 2.656,0.708 2.656,0.708 2.406,0.708 true 3.375,1.385 2.896,0.271 2.896,0.271 2.646,0.271 true 3,1.573 2.594,2.219 2.594,2.219 2.344,2.219 true 3.198,1.583 2.719,2.438 2.719,2.438 2.469,2.438 true 3.385,1.583 2.74,2.646 2.74,2.646 2.49,2.646 true 3.802,1.396 4.521,0.406 4.521,0.406 4.771,0.406 true 3.771,1.583 4.49,2.344 4.49,2.344 4.74,2.344 true 3.198,1.396 2.813,0.51 2.813,0.51 2.563,0.51 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 3.469,0.635 3.927,0.833 0.458,0.198 10 false G68 1.833,0.615 2.75,0.813 0.917,0.198 10 false CANH*b 1.99,0.406 2.906,0.604 0.917,0.198 10 false CANH*c 2.063,0.167 2.979,0.365 0.917,0.198 10 false CANH*d 4.802,0.323 5.719,0.521 0.917,0.198 10 false CANH*e 5.125,0.833 6.042,1.031 0.917,0.198 10 false CANH*f 1.802,2.115 2.719,2.313 0.917,0.198 10 false CANL*b 1.927,2.333 2.844,2.531 0.917,0.198 10 false CANL*c 1.969,2.552 2.885,2.75 0.917,0.198 10 false CANL*d 4.802,2.281 5.719,2.479 0.917,0.198 10 false CANL*e 5.125,1.906 6.042,2.104 0.917,0.198 10 false CANL*f
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b for Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System)
*c for 4 Wheel Drive Control ECU (for 4WD) *d for ECM
*e for No. 1 CAN Junction Connector *f
·

for Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System)

·

for Air Conditioning Amplifier Assembly (for Manual Air Conditioning System)




No. 2 CAN Junction Connector Wiring Color Connect to

*1: w/ Entry and Start System

*2: for 4WD

*3: for Automatic Air Conditioning System

*4: for Manual Air Conditioning System

G68-3 (CANH) G Certification ECU (smart key ECU assembly)*1
G68-13 (CANL) W
G68-4 (CANH) R 4 wheel drive control ECU*2
G68-14 (CANL) W
G68-5 (CANH) B ECM
G68-15 (CANL) W
G68-6 (CANH) LG No. 1 CAN junction connector
G68-16 (CANL) W
G68-10 (CANH) GR Air conditioning amplifier assembly*3, *4
G68-20 (CANL) W


c.

No. 3 CAN Junction Connector

C348056C03
3.323,0.552 3.875,0.875 0.552,0.323 3.198,1.385 2.844,0.698 2.844,0.698 2.594,0.698 true 3.208,1.573 2.802,2.219 2.802,2.219 2.552,2.219 true 3.417,1.594 2.938,2.448 2.938,2.448 2.688,2.448 true 3.802,1.396 4.521,0.406 4.521,0.406 4.771,0.406 true 3.771,1.583 4.49,2.344 4.49,2.344 4.74,2.344 true 3.385,1.406 3,0.521 3,0.521 2.75,0.521 true 4,1.406 4.594,0.625 4.594,0.625 4.844,0.625 true 3.99,1.563 4.635,2.125 4.635,2.125 4.885,2.125 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 3.438,0.635 3.896,0.833 0.458,0.198 10 false G131 2.021,0.635 2.938,0.833 0.917,0.198 10 false CANH*b 2.219,0.438 3.135,0.635 0.917,0.198 10 false CANH*c 4.802,0.333 5.719,0.531 0.917,0.198 10 false CANH*d 4.885,0.552 5.802,0.75 0.917,0.198 10 false CANH*d 2.021,2.125 2.938,2.323 0.917,0.198 10 false CANL*b 2.167,2.365 3.083,2.563 0.917,0.198 10 false CANL*c 4.792,2.271 5.708,2.469 0.917,0.198 10 false CANL*d 4.927,2.052 5.844,2.25 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b for Forward Recognition Camera
*c for Millimeter Wave Radar Sensor Assembly *d for Central Gateway ECU (Network Gateway ECU)


No. 3 CAN Junction Connector Wiring Color Connect to
G131-4 (CANH) Y Forward recognition camera
G131-14 (CANL) W
G131-5 (CANH) R Millimeter wave radar sensor assembly
G131-15 (CANL) W
G131-6 (CANH) G Central gateway ECU (network gateway ECU)
G131-16 (CANL) W
G131-7 (CANH) L
G131-17 (CANL) W


d.

No. 4 CAN Junction Connector

C348057C01
3.813,0.25 4.25,0.531 0.438,0.281 4.479,0.25 4.917,0.531 0.438,0.281 5,0.25 5.438,0.531 0.438,0.281 4.052,1.167 4.052,0.531 true 4.75,1.167 4.75,0.531 true 5.167,1.167 5.167,0.531 true 5.094,3.417 5.385,3.802 5.385,3.802 5.521,3.802 true 5.125,3.24 5.365,2.927 5.365,2.927 5.5,2.927 true 0.073,0.094 0.438,0.354 0.365,0.26 10 false *1 2.24,1.948 2.854,2.146 0.615,0.198 10 false G135 2.24,2.5 2.854,2.698 0.615,0.198 10 false G132 2.24,2.833 2.854,3.031 0.615,0.198 10 false G133 3.865,0.323 4.479,0.521 0.615,0.198 10 false G135 4.531,0.323 5.146,0.521 0.615,0.198 10 false G132 5.052,0.323 5.667,0.521 0.615,0.198 10 false G133 4.125,2.625 4.438,2.823 0.313,0.198 10 false *a 5.573,2.854 6.188,3.052 0.615,0.198 10 false CANH 5.583,3.729 6.198,3.927 0.615,0.198 10 false CANL
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


No. 4 CAN Junction Connector Wiring Color Connect to

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)

G132-1 (CANH) V
·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2


G132-2 (CANL) W
G133-1 (CANH) V Central gateway ECU (network gateway ECU)
G133-2 (CANL) W
G135-1 (CANH) P
G135-2 (CANL) W



CHECK DLC3


a.
C253362C15
0.167,1 0.583,1.25 0.417,0.25 1.948,0.906 2.167,0.417 2.167,0.417 2.417,0.417 true 1.583,0.906 1.25,0.5 1.25,0.5 1,0.5 true 1.927,1.49 1.667,1.917 1.667,1.917 1.417,1.917 true 2.333,1.5 2.5,1.833 2.5,1.833 2.75,1.833 true 0.292,1.052 0.75,1.25 0.458,0.198 10 false G8 0.75,0.417 1.208,0.615 0.458,0.198 10 false CG 2.469,0.344 2.927,0.542 0.458,0.198 10 false CANH 1.031,1.844 1.49,2.042 0.458,0.198 10 false CANL 2.802,1.76 3.26,1.958 0.458,0.198 10 false BAT 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click here

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here




b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G8-6 (CANH) - G8-14 (CANL) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G8-6 (CANH) - G8-4 (CG) L - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G8-14 (CANL) - G8-4 (CG) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G8-6 (CANH) - G8-16 (BAT) L - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G8-14 (CANL) - G8-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C331365C24
3.281,0.313 3.76,0.573 0.479,0.26 4.438,0.854 4.167,0.854 4.167,0.854 3.896,1.333 true 2.615,0.417 2.844,0.417 2.844,0.417 3.25,1.333 true 4.448,2.021 4.24,2.021 4.24,2.021 3.854,1.469 true 2.771,2.146 3,2.146 3,2.146 3.313,1.469 true 2.906,2.323 3.094,2.323 3.094,2.323 3.375,1.469 true 3.073,2.531 3.25,2.531 3.25,2.531 3.458,1.469 true 4.156,2.49 3.896,2.49 3.896,2.49 3.615,1.469 true 4.052,2.677 3.792,2.677 3.792,2.677 3.542,1.458 true 4.365,2.156 4.156,2.156 4.156,2.156 3.771,1.469 true 4.302,2.281 4.094,2.281 4.094,2.281 3.698,1.458 true 2.344,0.802 2.573,0.802 2.573,0.802 3.021,1.344 true 1.875,1.979 2.104,1.979 2.104,1.979 2.969,1.458 true 1.927,1.104 2.156,1.104 2.156,1.104 2.948,1.354 true 5.313,1.073 5.042,1.073 5.042,1.073 4.198,1.354 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 3.365,0.365 3.979,0.563 0.615,0.198 10 false G128 4.51,0.781 5.177,0.99 0.667,0.208 10 false CA6L*A 2.052,0.344 2.635,0.552 0.583,0.208 10 false CA3H*C 4.51,1.927 5.281,2.125 0.771,0.198 10 false CA6H*A 2.24,2.063 2.802,2.271 0.563,0.208 10 false CA3L*C 2.354,2.25 2.927,2.458 0.573,0.208 10 false CAYL*C 2.49,2.458 3.052,2.667 0.563,0.208 10 false CAYH*C 4.208,2.406 4.833,2.625 0.625,0.219 10 false CA4L*B 4.104,2.594 4.833,2.781 0.729,0.188 10 false CA4H*B 4.385,2.073 5.156,2.271 0.771,0.198 10 false CA5H*D 4.333,2.219 5,2.427 0.667,0.208 10 false CA5L*D 1.813,0.719 2.396,0.927 0.583,0.208 10 false CAXH*D 1.323,1.896 1.906,2.104 0.583,0.208 10 false CAXL*D 5.344,1 6.01,1.208 0.667,0.208 10 false BATT 1.583,1.021 2.25,1.229 0.667,0.208 10 false GND
*A V Bus *B Bus 2
*C Bus 3 *D Bus 5
*a Component without harness connected
(Central Gateway ECU [Network Gateway ECU])
- -


a.
C343190C69
1.667,0.208 2.198,0.458 0.531,0.25 1.094,1.875 1.24,1.875 1.24,1.875 1.667,1.271 true 1.323,2.052 1.469,2.052 1.469,2.052 1.771,1.271 true 2.646,0.26 2.49,0.26 2.49,0.26 2.125,1.115 true 2.823,0.729 2.667,0.729 2.667,0.729 2.469,1.115 true 2.844,1.542 2.729,1.542 2.729,1.542 2.563,1.281 true 0.719,0.677 0.865,0.677 0.865,0.677 1.302,1.094 true 0.927,0.458 1.073,0.458 1.073,0.458 1.573,1.26 true 1.219,0.198 1.365,0.198 1.365,0.198 1.854,1.271 true 2.396,2.063 2.26,2.063 2.26,2.063 1.958,1.271 true 2.646,1.833 2.51,1.833 2.51,1.833 2.063,1.271 true 2.906,1.021 2.75,1.021 2.75,1.021 2.604,1.115 true 0.448,1.344 0.594,1.344 0.594,1.344 0.823,1.115 true 0.667,1.688 0.813,1.688 0.813,1.688 1.479,1.271 true 0.615,0.865 0.76,0.865 0.76,0.865 1.365,1.271 true 1.771,0.25 2.188,0.427 0.417,0.177 10 false G128 0.073,0.104 0.385,0.26 0.313,0.156 10 false *a 0.781,1.938 1.375,2.167 0.594,0.229 10 false CA4H*A 0.563,1.781 1.156,2.01 0.594,0.229 10 false CA4L*A 2.719,0.135 3.313,0.365 0.594,0.229 10 false CA3H*B 2.875,0.615 3.427,0.844 0.552,0.229 10 false CAXH*C 2.885,1.438 3.396,1.698 0.51,0.26 10 false CAXL*C 0.396,0.344 0.906,0.604 0.51,0.26 10 false CA5L*C 0.177,0.573 0.76,0.823 0.583,0.25 10 false CA6L*D 0.656,0.104 1.229,0.365 0.573,0.26 10 false CAYH*B 2.438,1.958 3.01,2.156 0.573,0.198 10 false CAYL*B 2.698,1.719 3.292,1.948 0.594,0.229 10 false CA3L*B 2.958,0.938 3.354,1.208 0.396,0.271 10 false GND 0.104,1.25 0.563,1.521 0.458,0.271 10 false BATT 0.094,1.573 0.677,1.823 0.583,0.25 10 false CA5H*C 0.063,0.792 0.646,1.042 0.583,0.25 10 false CA6H*D
*A Bus 2
*B Bus 3
*C Bus 5
*D V Bus
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

V Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G128-14 (CA6H) - G128-5 (CA6L) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 1 MΩ or higher
G128-14 (CA6H) - G128-10 (GND) L - B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-5 (CA6L) - G128-10 (GND) W - B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-14 (CA6H) - G128-1 (BATT) L - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G128-5 (CA6L) - G128-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 2
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G128-18 (CA4H) - G128-17 (CA4L) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G128-18 (CA4H) - G128-10 (GND) R - B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-17 (CA4L) - G128-10 (GND) W - B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-18 (CA4H) - G128-1 (BATT) R - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G128-17 (CA4L) - G128-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 3
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G128-6 (CA3H) - G128-21 (CA3L) P - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 1 MΩ or higher
G128-6 (CA3H) - G128-19 (CAYH) P - V HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
G128-21 (CA3L) - G128-20 (CAYL) W - W LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
G128-6 (CA3H) - G128-10 (GND) P - B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-21 (CA3L) - G128-10 (GND) W - B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-6 (CA3H) - G128-1 (BATT) P - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G128-21 (CA3L) - G128-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 5
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G128-15 (CA5H) - G128-16 (CA5L) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 1 MΩ or higher
G128-15 (CA5H) - G128-9 (CAXH) G - L HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
G128-16 (CA5L) - G128-24 (CAXL) W - W LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
G128-15 (CA5H) - G128-10 (GND) G - B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-16 (CA5L) - G128-10 (GND) W - B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-15 (CA5H) - G128-1 (BATT) G - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G128-16 (CA5L) - G128-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM


Refer to Terminals of ECU.

ECD SYSTEM (w/ DPF): Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>TERMINALS OF ECM

ECD SYSTEM (w/ Urea SCR System): Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>TERMINALS OF ECM

a.

Disconnect the ECM connectors.

C317088C04
1,0.448 1.448,0.719 0.448,0.271 3.25,0.438 3.698,0.708 0.448,0.271 5.552,0.406 6,0.677 0.448,0.271 0.521,0.896 0.656,0.896 0.656,0.896 0.698,1.396 true 2.667,0.979 2.802,0.979 2.802,0.979 2.927,1.688 true 4.917,0.865 5.052,0.865 5.052,0.865 5.219,1.406 true 2.625,2.323 2.76,2.323 2.76,2.323 2.927,1.906 true 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 1.094,0.51 1.552,0.708 0.458,0.198 10 false G86 3.344,0.49 3.802,0.688 0.458,0.198 10 false G85 5.656,0.469 6.115,0.667 0.458,0.198 10 false C60 0.125,0.823 0.531,1.031 0.406,0.208 10 false BATT 4.677,0.781 4.958,0.969 0.281,0.188 10 false E1 2.219,0.906 2.625,1.115 0.406,0.208 10 false CANH 2.219,2.25 2.625,2.458 0.406,0.208 10 false CANL
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G85-17 (CANH) - G85-28 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G85-17 (CANH) - C60-1 (E1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G85-28 (CANL) - C60-1 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G85-17 (CANH) - G86-1 (BATT) B - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G85-28 (CANL) - G86-1 (BATT) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.
C240157C58
1.531,0.146 1.969,0.458 0.438,0.313 1.396,1.25 2.104,1.781 2.104,1.781 2.333,1.781 true 1.302,1.24 1.042,1.865 1.042,1.865 0.802,1.865 true 2.865,1.448 2.708,1.448 2.708,1.448 2.563,1.229 true 2.635,0.552 2.479,0.552 2.479,0.552 2.052,1.198 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.635,0.229 2.094,0.427 0.458,0.198 10 false G9 0.385,1.802 0.802,2 0.417,0.198 10 false CANH 2.375,1.708 2.854,1.906 0.479,0.198 10 false CANL 2.917,1.385 3.219,1.656 0.302,0.271 10 false B 2.698,0.469 3.063,0.729 0.365,0.26 10 false EP
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G9-36 (CANH) - G9-35 (CANL) SB - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G9-36 (CANH) - G9-27 (EP) SB - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G9-35 (CANL) - G9-27 (EP) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G9-36 (CANH) - G9-21 (B) SB - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G9-35 (CANL) - G9-21 (B) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIRBAG SENSOR ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>TERMINALS OF ECU

a.
C227529C07
0.375,2.521 0.771,2.781 0.396,0.26 0.365,0.948 0.76,1.208 0.396,0.26 2.198,2.896 2.333,3.115 2.333,3.115 2.552,3.115 true 2.115,1.323 2.313,1.677 2.313,1.677 2.552,1.677 true 2.021,1.01 2.438,0.656 2.438,0.656 2.688,0.656 true 1.208,1.677 1.438,1.677 1.438,1.677 1.76,1.323 true 0.177,0.073 0.427,0.271 0.25,0.198 10 false *a 0.198,2.083 0.51,2.24 0.313,0.156 10 false *b 0.479,2.573 0.823,2.781 0.344,0.208 10 false G8 0.417,1 0.76,1.208 0.344,0.208 10 false G42 2.75,0.583 3.292,0.792 0.542,0.208 10 false CANH 2.604,1.604 3.146,1.813 0.542,0.208 10 false CANL 2.604,3.042 3.146,3.25 0.542,0.208 10 false BAT 1,1.604 1.542,1.813 0.542,0.208 10 false E1
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>PRECAUTION


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G42-13 (CANH) - G42-22 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G42-13 (CANH) - G42-25 (E1) Y - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G42-22 (CANL) - G42-25 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G42-13 (CANH) - G8-16 (BAT) Y - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G42-22 (CANL) - G8-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the brake actuator assembly (skid control ECU) connector.

C306842C08
3.448,0.292 3.781,0.573 0.333,0.281 3.938,1.115 4.708,0.656 4.708,0.656 4.885,0.656 true 4.375,1.188 4.906,1.875 4.906,1.875 5.083,1.875 true 3.958,1.281 4.729,2.333 4.729,2.333 4.906,2.333 true 2.771,1.417 2.406,2.063 2.406,2.063 2.208,2.063 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 3.531,0.354 3.99,0.552 0.458,0.198 10 false A4 4.938,0.583 5.552,0.781 0.615,0.198 10 false CANL 4.99,2.25 5.604,2.448 0.615,0.198 10 false CANH 5.125,1.802 5.74,2 0.615,0.198 10 false BM 1.792,1.979 2.406,2.177 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A4-22 (CANH) - A4-10 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A4-22 (CANH) - A4-25 (GND1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A4-10 (CANL) - A4-25 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A4-22 (CANH) - A4-13 (BM) B - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A4-10 (CANL) - A4-13 (BM) W - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)


C228050E06
1.458,0.365 1.885,0.646 0.427,0.281 1.906,1.354 2.188,1.719 2.188,1.719 2.5,1.719 true 1.74,1.354 1.563,1.844 1.563,1.844 1.281,1.844 true 2.125,1.313 2.458,0.99 2.458,0.99 2.771,0.99 true 1.323,1.333 1.021,1.031 1.021,1.031 0.74,1.031 true 1.531,0.427 1.854,0.615 0.323,0.188 10 false G21 2.833,0.896 3.24,1.052 0.406,0.156 10 false ESS 2.552,1.635 3.052,1.844 0.5,0.208 10 false CANL 0.875,1.76 1.375,1.969 0.5,0.208 10 false CANH 0.438,0.958 0.938,1.167 0.5,0.208 10 false BAT

a.
C277459C19
1.521,0.188 1.938,0.438 0.417,0.25 1.094,1.844 1.344,1.844 1.344,1.844 1.521,1.396 true 2.563,0.875 2.333,0.875 2.333,0.875 2.115,1.24 true 2.24,1.844 1.99,1.844 1.99,1.844 1.75,1.396 true 0.771,0.906 1.021,0.906 1.021,0.906 1.344,1.219 true 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 2.625,0.781 3.104,0.938 0.479,0.156 10 false BAT 0.458,0.823 0.938,0.979 0.479,0.156 10 false ESS 1.594,0.219 2.073,0.375 0.479,0.156 10 false G21 2.302,1.75 2.781,1.906 0.479,0.156 10 false CANH 0.688,1.76 1.167,1.917 0.479,0.156 10 false CANL
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G21-3 (CANH) - G21-2 (CANL) BE - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G21-3 (CANH) - G21-1 (ESS) BE - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G21-2 (CANL) - G21-1 (ESS) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G21-3 (CANH) - G21-5 (BAT) BE - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G21-2 (CANL) - G21-5 (BAT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


Refer to Terminals of ECU.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>TERMINALS OF ECU

a.

Disconnect the certification ECU (smart key ECU assembly) connectors.

E277246C07
1.875,0.667 2.292,0.917 0.417,0.25 4.74,0.667 5.156,0.917 0.417,0.25 1.229,1.365 0.865,2.167 0.865,2.167 0.719,2.167 true 2.896,1.333 3.135,2.208 3.135,2.208 3.271,2.208 true 6.333,0.854 6.198,0.854 6.198,0.854 6.063,1.313 true 6.031,1.49 6.177,2.188 6.177,2.188 6.333,2.188 true 0.167,0.104 0.479,0.302 0.313,0.198 10 false *a 0.469,2.104 0.729,2.302 0.26,0.198 10 false +B 3.354,2.135 3.667,2.333 0.313,0.198 10 false E 6.417,0.781 6.813,0.979 0.396,0.198 10 false CANL 6.396,2.115 6.885,2.313 0.49,0.198 10 false CANH 1.969,0.708 2.427,0.906 0.458,0.198 10 false G69 4.844,0.708 5.302,0.906 0.458,0.198 10 false G70
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G70-40 (CANH) - G70-18 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G70-40 (CANH) - G69-10 (E) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G70-18 (CANL) - G69-10 (E) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G70-40 (CANH) - G69-1 (+B) G - P HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G70-18 (CANL) - G69-1 (+B) W - P LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System [for Radio and Display Type])


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>TERMINALS OF ECU

a.
C277477C21
1.5,0.24 1.938,0.479 0.438,0.24 1.469,1.833 1.906,2.073 0.438,0.24 2.146,1.594 1.896,1.594 1.896,1.594 1.677,1.125 true 2.635,0.719 2.385,0.719 2.385,0.719 2.188,0.875 true 2.5,3.135 2.25,3.135 2.25,3.135 2.031,2.667 true 1.896,2.646 1.688,3.177 1.688,3.177 1.438,3.177 true 2.198,1.51 2.74,1.74 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.594,0.281 2.052,0.479 0.458,0.198 10 false G40 1.563,1.865 2.021,2.063 0.458,0.198 10 false G37 2.677,0.625 3.219,0.854 0.542,0.229 10 false +B1 2.552,3.063 3.094,3.292 0.542,0.229 10 false CANL 1.031,3.083 1.573,3.313 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G37-9 (CANH) - G37-10 (CANL) V - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G37-9 (CANH) - G40-7 (GND1) V - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G37-10 (CANL) - G40-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G37-9 (CANH) - G40-4 (+B1) V - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G37-10 (CANL) - G40-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>TERMINALS OF ECU

a.
C277477C23
1.5,0.24 1.938,0.479 0.438,0.24 1.469,1.833 1.906,2.073 0.438,0.24 2.146,1.594 1.896,1.594 1.896,1.594 1.677,1.125 true 2.635,0.719 2.385,0.719 2.385,0.719 2.188,0.875 true 2.5,3.135 2.25,3.135 2.25,3.135 2.031,2.667 true 1.896,2.646 1.688,3.177 1.688,3.177 1.438,3.177 true 2.198,1.51 2.74,1.74 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.552,0.281 2.01,0.479 0.458,0.198 10 false G115 1.521,1.865 1.979,2.063 0.458,0.198 10 false G113 2.677,0.625 3.219,0.854 0.542,0.229 10 false +B1 2.552,3.063 3.094,3.292 0.542,0.229 10 false CANL 1.031,3.083 1.573,3.313 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Navigation Receiver assembly)


Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G113-9 (CANH) - G113-10 (CANL) V - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G113-9 (CANH) - G115-7 (GND1) V - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G113-10 (CANL) - G115-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G113-9 (CANH) - G115-4 (+B1) V - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G113-10 (CANL) - G115-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK 4 WHEEL DRIVE CONTROL ECU (for 4WD)


Refer to Terminals of ECU.

Click hereDrivetrain>VF2CM TRANSFER / 4WD / AWD>TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM>TERMINALS OF ECU

a.
C325480C06
1.521,0.365 1.927,0.615 0.406,0.25 1.427,2.292 1.792,2.542 0.365,0.25 0.521,1.458 0.969,1.927 0.969,1.927 1.135,1.927 true 2.302,3.573 2.708,4.25 2.708,4.25 2.854,4.25 true 2.719,0.573 2.844,0.573 2.844,0.573 2.906,1.229 true 2.688,1.958 2.813,1.958 2.813,1.958 2.906,1.448 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.604,0.406 2.063,0.604 0.458,0.198 10 false C39 1.49,2.333 1.948,2.531 0.458,0.198 10 false C40 1.188,1.896 1.5,2.094 0.313,0.198 10 false +B 2.906,4.177 3.219,4.375 0.313,0.198 10 false GND 2.271,1.885 2.729,2.083 0.458,0.198 10 false CANL 2.271,0.5 2.729,0.698 0.458,0.198 10 false CANH
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)


Disconnect the 4 wheel drive control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C39-20 (CANH) - C39-40 (CANL) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
C39-20 (CANH) - C40-10 (GND) R - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
C39-40 (CANL) - C40-10 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
C39-20 (CANH) - C39-21 (+B) R - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
C39-40 (CANL) - C39-21 (+B) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)


Refer to Terminals of ECU.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>TERMINALS OF ECU

a.
C240157C59
0.24,0.969 0.677,1.281 0.438,0.313 1.719,1.115 2.052,0.469 2.052,0.469 2.281,0.469 true 1.635,1.115 1.958,0.219 1.958,0.219 2.188,0.219 true 1.479,1.104 1.219,0.448 1.219,0.448 1,0.448 true 2.99,1.604 2.781,1.604 2.781,1.604 2.563,1.229 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.344,1.063 0.802,1.26 0.458,0.198 10 false G33 2.333,0.406 2.792,0.604 0.458,0.198 10 false TX+ 2.24,0.156 2.698,0.354 0.458,0.198 10 false TX- 3.031,1.531 3.333,1.802 0.302,0.271 10 false B 0.667,0.385 1.031,0.646 0.365,0.26 10 false GND
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G33-11 (TX+) - G33-12 (TX-) GR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G33-11 (TX+) - G33-14 (GND) GR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G33-12 (TX-) - G33-14 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G33-11 (TX+) - G33-21 (B) GR - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G33-12 (TX-) - G33-21 (B) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System)


Refer to Terminals of ECU.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>TERMINALS OF ECU

a.
C300856C10
1.542,2.781 1.958,3.052 0.417,0.271 1.396,0.208 1.813,0.479 0.417,0.271 1.865,1.927 1.979,1.927 1.979,1.927 2.521,1.063 true 2.656,1 2.823,0.354 2.823,0.354 2.958,0.354 true 1.781,4.427 1.906,4.427 1.906,4.427 2.417,3.958 true 1.979,2.292 2.094,2.292 2.094,2.292 2.635,1.229 true 0.146,0.104 0.458,0.26 0.313,0.156 10 false *a 0.198,2.635 0.51,2.792 0.313,0.156 10 false *b 1.656,2.844 1.938,3.01 0.281,0.167 10 false G8 1.479,0.26 1.844,0.417 0.365,0.156 10 false G77 1.583,1.813 2.01,1.969 0.427,0.156 10 false TX+ 3,0.25 3.427,0.406 0.427,0.156 10 false TX- 1.469,4.365 1.896,4.521 0.427,0.156 10 false BAT 1.635,2.188 2.063,2.344 0.427,0.156 10 false GND
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G77-8 (TX+) - G77-9 (TX-) GR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G77-8 (TX+) - G77-23 (GND) GR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G77-9 (TX-) - G77-23 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G77-8 (TX+) - G8-16 (BAT) GR - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G77-9 (TX-) - G8-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK HEADLIGHT LEVELING ECU ASSEMBLY (for LED Headlight or w/ Headlight Cleaner System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.
C281183C07
1.573,0.229 1.938,0.49 0.365,0.26 0.292,2.51 0.656,2.771 0.365,0.26 2.552,3.094 2.406,3.094 2.406,3.094 2.219,2.823 true 2.75,0.448 2.604,0.448 2.604,0.448 2.375,0.99 true 2.552,0.208 2.406,0.208 2.406,0.208 2.25,1.01 true 2,1.885 2.188,1.885 2.188,1.885 2.625,1.052 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.104,1.979 0.417,2.135 0.313,0.156 10 false *b 0.385,2.542 0.698,2.698 0.313,0.156 10 false G8 2.625,3.01 3.083,3.26 0.458,0.25 10 false BAT 1.615,0.271 1.927,0.427 0.313,0.156 10 false G80 2.615,0.094 3.104,0.292 0.49,0.198 10 false CANH 2.802,0.354 3.292,0.552 0.49,0.198 10 false CANL 1.75,1.813 1.979,2.01 0.229,0.198 10 false E1
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)
*b Front view of DLC3


Disconnect the headlight leveling ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G80-6 (CANH) - G80-7 (CANL) V - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G80-6 (CANH) - G80-9 (E1) V - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-7 (CANL) - G80-9 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-6 (CANH) - G8-16 (BAT) V - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G80-7 (CANL) - G8-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ENGINE STOP AND START ECU (w/ Stop and Start System)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

a.
C323601C23
1.51,0.177 1.938,0.448 0.427,0.271 1.531,2.052 1.958,2.323 0.427,0.271 0.604,1.615 0.75,1.615 0.75,1.615 1.156,1.385 true 1.365,4.146 1.24,4.146 1.24,4.146 0.781,3.521 true 0.917,4.406 0.792,4.406 0.792,4.406 0.615,3.521 true 2.813,1.917 2.688,1.917 2.688,1.917 2.344,1.417 true 0.115,0.052 0.427,0.25 0.313,0.198 10 false *a 1.563,0.229 2.021,0.427 0.458,0.198 10 false G125 0.281,1.542 0.74,1.74 0.458,0.198 10 false BIN1 1.594,2.115 2.052,2.313 0.458,0.198 10 false G127 1.417,4.083 2.083,4.385 0.667,0.302 10 false CANL 0.969,4.323 1.573,4.563 0.604,0.24 10 false CANH 2.865,1.833 3.313,2.031 0.448,0.198 10 false GND1
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G127-13 (CANH) - G127-14 (CANL) P - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G127-13 (CANH) - G125-8 (GND1) P - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G127-14 (CANL) - G125-8 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G127-13 (CANH) - G125-3 (BIN1) P - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G127-14 (CANL) - G125-3 (BIN1) W - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK FORWARD RECOGNITION CAMERA


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>TERMINALS OF ECU

a.
C267485C22
0.563,1.063 0.99,1.344 0.427,0.281 0.396,2.542 0.823,2.823 0.427,0.281 2.198,2.917 2.344,3.125 2.344,3.125 2.563,3.125 true 1.792,1.375 1.427,1.792 1.427,1.792 1.208,1.792 true 1.927,1.385 2.135,1.802 2.135,1.802 2.354,1.802 true 1.906,1.125 2.281,0.594 2.281,0.594 2.5,0.594 true 0.083,0.083 0.396,0.25 0.313,0.167 10 false *a 0.167,2.094 0.479,2.25 0.313,0.156 10 false *b 2.615,3.052 2.969,3.24 0.354,0.188 10 false BAT 0.521,2.594 0.875,2.781 0.354,0.188 10 false G8 0.698,1.115 1.052,1.302 0.354,0.188 10 false Q4 0.865,1.698 1.333,1.885 0.469,0.188 10 false GND 2.542,0.5 3.229,0.771 0.688,0.271 10 false CA1P 2.385,1.688 3.146,1.927 0.76,0.24 10 false CA1N
*a Front view of wire harness connector
(to Forward Recognition Camera)
*b Front view of DLC3


Disconnect the forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q4-5 (CA1P) - Q4-11 (CA1N) B - V HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
Q4-5 (CA1P) - Q4-10 (GND) B - B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q4-11 (CA1N) - Q4-10 (GND) V - B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q4-5 (CA1P) - G8-16 (BAT) B - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q4-11 (CA1N) - G8-16 (BAT) V - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>TERMINALS OF ECU

a.
C339037C11
0.25,2.396 0.719,2.646 0.469,0.25 2.51,0.625 2.979,0.875 0.469,0.25 2.313,2.771 2.573,3.021 2.573,3.021 2.75,3.021 true 0.792,0.635 0.948,0.635 0.948,0.635 1.458,0.865 true 1.052,0.365 1.208,0.365 1.208,0.365 1.625,0.844 true 1.323,0.156 1.479,0.156 1.479,0.156 1.75,0.854 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 0.115,1.833 0.427,1.99 0.313,0.156 10 false *b 0.365,2.438 0.677,2.594 0.313,0.156 10 false G8 2.646,0.677 2.99,0.917 0.344,0.24 10 false A64 2.802,2.885 3.24,3.063 0.438,0.177 10 false BAT 0.375,0.531 0.969,0.708 0.594,0.177 10 false SGND 0.667,0.271 1.26,0.448 0.594,0.177 10 false CA2L 0.938,0.073 1.531,0.25 0.594,0.177 10 false CA2H
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
*b Front view of DLC3


Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A64-3 (CA2H) - A64-2 (CA2L) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A64-3 (CA2H) - A64-1 (SGND) R - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A64-2 (CA2L) - A64-1 (SGND) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A64-3 (CA2H) - G8-16 (BAT) R - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A64-2 (CA2L) - G8-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher