Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0262517 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the GTS.

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of ECM

·

ECM ground circuit

·

ECM CAN main wire or connector

·

ECM



WIRING DIAGRAM

C317092E09
5.688,0.583 6.302,0.781 0.615,0.198 10 false CANH 5.677,1.365 6.292,1.563 0.615,0.198 10 false CANL 5.344,1.01 5.656,1.208 0.313,0.198 10 false 28 5.365,0.469 5.677,0.667 0.313,0.198 10 false 17 5.302,0.708 5.76,0.906 0.458,0.198 10 false G85 5.302,1.229 5.76,1.427 0.458,0.198 10 false G85 0.063,1.438 0.521,1.635 0.458,0.198 10 false G68 0.063,1.625 4.344,1.823 4.281,0.198 10 false No. 2 CAN Junction Connector 1.667,0.552 1.979,0.75 0.313,0.198 10 false 5 1.656,1.073 1.969,1.271 0.313,0.198 10 false 15 5.729,3.854 6.344,4.052 0.615,0.198 10 false MREL 5.729,2.531 6.344,2.729 0.615,0.198 10 false +B 5.719,2.969 6.333,3.167 0.615,0.198 10 false +B2 5.698,3.438 6.313,3.635 0.615,0.198 10 false +B3 5.698,1.958 6.313,2.156 0.615,0.198 10 false BATT 5.719,4.333 6.333,4.531 0.615,0.198 10 false IGSW 5.708,4.844 6.323,5.042 0.615,0.198 10 false E1 5.344,4.833 5.802,5.031 0.458,0.198 10 false C60 5.885,5.365 6.344,5.563 0.458,0.198 10 false ECM 5.396,4.615 5.708,4.813 0.313,0.198 10 false 1 5.385,1.74 5.698,1.938 0.313,0.198 10 false 1 5.313,1.969 5.771,2.167 0.458,0.198 10 false G86 5.323,4.333 5.781,4.531 0.458,0.198 10 false G86 5.354,4.115 5.667,4.313 0.313,0.198 10 false 18 5.344,3.625 5.656,3.823 0.313,0.198 10 false 14 5.302,3.865 5.76,4.063 0.458,0.198 10 false G85 5.302,2.531 5.76,2.729 0.458,0.198 10 false G86 5.302,2.979 5.76,3.177 0.458,0.198 10 false G86 5.313,3.427 5.771,3.625 0.458,0.198 10 false G86 5.385,2.292 5.698,2.49 0.313,0.198 10 false 2 5.375,2.771 5.688,2.969 0.313,0.198 10 false 3 5.385,3.188 5.698,3.385 0.313,0.198 10 false 4 0.781,2.5 2.49,2.875 1.708,0.375 10 false from EFI-MAIN NO.1 Relay 0.302,4.313 2.49,4.573 2.188,0.26 10 false from IG2 Relay*1, Ignition Switch*2 3.635,1.802 4.448,2 0.813,0.198 10 false EFI-B 3.5,4.156 4.313,4.354 0.813,0.198 10 false IG2 NO.1 1.646,1.969 2.479,2.344 0.833,0.375 10 false from Battery 0.927,3.833 2.479,4.135 1.552,0.302 10 false to EFI-MAIN NO.1 Relay 0.167,4.875 2.656,5.135 2.49,0.26 10 false *1: w/ Entry and Start System 0.156,5.25 2.75,5.573 2.594,0.323 10 false *2: w/o Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Drive the vehicle at a speed of 15 km/h (9 mph) or more for 3 seconds or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)
a.
C317098C10
1.458,0.823 1.906,1.104 0.448,0.281 0.667,1.885 0.813,1.885 0.813,1.885 1.063,2.094 true 0.677,2.906 0.823,2.906 0.823,2.906 1.073,2.344 true 1.563,0.896 2.021,1.094 0.458,0.198 10 false G85 0.208,1.792 0.688,1.99 0.479,0.198 10 false CANH 0.24,2.823 0.688,3.021 0.448,0.198 10 false CANL 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-17 (CANH) - G85-28 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE ECM CAN MAIN WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


C317088C03
1,0.448 1.448,0.719 0.448,0.271 3.25,0.438 3.698,0.708 0.448,0.271 5.552,0.406 6,0.677 0.448,0.271 0.469,1.052 0.604,1.052 0.604,1.052 0.688,1.406 true 3,0.823 3.135,0.823 3.135,0.823 3.823,1.573 true 4.917,0.865 5.052,0.865 5.052,0.865 5.219,1.406 true 0.5,2.417 0.635,2.417 0.635,2.417 0.708,1.771 true 0.49,0.823 0.625,0.823 0.625,0.823 0.865,1.396 true 0.615,0.594 0.75,0.594 0.75,0.594 1.031,1.396 true 1.896,0.896 1.729,0.896 1.729,0.896 1.24,1.406 true 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 1.094,0.51 1.552,0.708 0.458,0.198 10 false G86 3.333,0.49 3.792,0.688 0.458,0.198 10 false G85 5.656,0.469 6.115,0.667 0.458,0.198 10 false C60 0.063,0.969 0.469,1.177 0.406,0.208 10 false BATT 4.677,0.781 4.958,0.969 0.281,0.188 10 false E1 2.573,0.75 2.979,0.958 0.406,0.208 10 false MREL 0.24,0.75 0.646,0.958 0.406,0.208 10 false +B 0.302,0.531 0.708,0.74 0.406,0.208 10 false +B2 1.958,0.813 2.365,1.021 0.406,0.208 10 false +B3 0.073,2.344 0.531,2.573 0.458,0.229 10 false IGSW
*a Front view of wire harness connector
(to ECM)
- -



b.

Disconnect the ECM connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G86-1 (BATT) - Body ground Always 11 to 14 V
G86-2 (+B) - Body ground Battery positive (+) voltage applied to terminal G85-14 (MREL) 11 to 14 V
G86-3 (+B2) - Body ground Battery positive (+) voltage applied to terminal G85-14 (MREL) 11 to 14 V
G86-4 (+B3) - Body ground Battery positive (+) voltage applied to terminal G85-14 (MREL) 11 to 14 V
G86-18 (IGSW) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C60-1 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR