Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0262517 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Open in Bus 2 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the bus 2 CAN main wires when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 18 (CA4H) and 17 (CA4L) of central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main wire or connector

·

CAN branch wire or connector

·

ECM

·

Combination meter assembly

·

Central gateway ECU (network gateway ECU)

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C348069E01
3.396,1.542 5.396,1.802 2,0.26 10 false No. 2 CAN Junction Connector 1.479,3.573 3.479,3.833 2,0.26 10 false No. 1 CAN Junction Connector 6.229,1.698 6.771,2.083 0.542,0.385 10 false ECM 6.25,1.542 6.792,1.927 0.542,0.385 10 false G85 6.031,0.563 6.542,0.813 0.51,0.25 10 false CANH 6.042,1.24 6.552,1.49 0.51,0.25 10 false CANL 5.688,0.583 6.198,0.833 0.51,0.25 10 false 17 5.698,1 6.208,1.25 0.51,0.25 10 false 28 4.813,0.583 5.323,0.833 0.51,0.25 10 false 5 4.792,0.99 5.302,1.24 0.51,0.25 10 false 15 3.823,0.573 4.333,0.823 0.51,0.25 10 false 6 3.76,0.99 4.271,1.24 0.51,0.25 10 false 16 2.833,0.563 3.344,0.813 0.51,0.25 10 false 6 2.813,0.969 3.323,1.219 0.51,0.25 10 false 16 1.979,0.573 2.49,0.823 0.51,0.25 10 false 9 1.917,0.979 2.427,1.229 0.51,0.25 10 false 19 2.823,2.531 3.333,2.781 0.51,0.25 10 false 5 2.792,2.99 3.302,3.24 0.51,0.25 10 false 15 5.156,3.583 7.156,3.844 2,0.26 10 false Combination Meter Assembly 5.156,3.406 7.156,3.667 2,0.26 10 false G9 6.063,2.594 6.573,2.844 0.51,0.25 10 false CANH 6.073,3.281 6.583,3.531 0.51,0.25 10 false CANL 5.677,2.604 6.188,2.854 0.51,0.25 10 false 36 5.677,2.99 6.188,3.24 0.51,0.25 10 false 35 0.885,0.698 1.396,0.948 0.51,0.25 10 false CA4H 0.896,1.135 1.406,1.385 0.51,0.25 10 false CA4L 1.427,0.573 1.938,0.823 0.51,0.25 10 false 18 1.438,0.969 1.948,1.219 0.51,0.25 10 false 17 0.073,1.51 2.042,1.885 1.969,0.375 10 false G128 0.063,1.688 2.031,2.063 1.969,0.375 10 false Central Gateway ECU (Network Gateway ECU) 1.479,3.427 3.479,3.688 2,0.26 10 false G67 3.396,1.406 5.396,1.667 2,0.26 10 false G68

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.

C343209C52
3.333,0.198 3.833,0.448 0.5,0.25 2.625,0.26 2.813,0.26 2.813,0.26 3.385,0.854 true 2.583,1.604 2.771,1.604 2.771,1.604 3.417,1.031 true 4.667,0.292 4.49,0.292 4.49,0.292 3.781,0.854 true 4.729,1.552 4.552,1.552 4.552,1.552 3.771,1.021 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 4.719,0.229 5.292,0.438 0.573,0.208 10 false CANH*c 4.76,1.469 5.323,1.677 0.563,0.208 10 false CANL*c 3.448,0.24 3.906,0.438 0.458,0.198 10 false G68 2.063,0.177 2.635,0.385 0.573,0.208 10 false CANH*b 2.042,1.531 2.604,1.74 0.563,0.208 10 false CANL*b
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to ECM
*c to No. 1 CAN Junction Connector - -



b.

Disconnect the No. 2 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G68-5 (CANH) - G68-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G68-6 (CANH) - G68-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction connector CAN main wire) B
NG (ECM CAN main wire) C



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

8.CONNECT CONNECTOR
2.CONNECT CONNECTOR
a.

Reconnect the G68 No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

C343209C53
1.823,0.792 2.323,1.042 0.5,0.25 2.698,0.24 2.885,0.24 2.885,0.24 3.385,0.844 true 2.75,1.573 2.938,1.573 2.938,1.573 3.396,1.021 true 4.667,0.406 4.479,0.406 4.479,0.406 4.323,0.844 true 4.521,0.135 4.333,0.135 4.333,0.135 3.781,0.865 true 4.75,1.396 4.563,1.396 4.563,1.396 4.313,1.031 true 4.438,1.625 4.25,1.625 4.25,1.625 3.771,1.021 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 2.115,0.146 2.698,0.375 0.583,0.229 10 false CANH*b 4.583,0.01 5.198,0.219 0.615,0.208 10 false CANH*c 2.219,1.479 2.792,1.698 0.573,0.219 10 false CANL*b 4.51,1.5 5.125,1.708 0.615,0.208 10 false CANL*c 1.938,0.833 2.396,1.031 0.458,0.198 10 false G67 4.771,0.281 5.385,0.49 0.615,0.208 10 false CANH*d 4.813,1.26 5.427,1.469 0.615,0.208 10 false CANL*d
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Combination Meter Assembly
*c to No. 2 CAN Junction Connector *d to Central Gateway ECU (Network Gateway ECU)



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G67-5 (CANH) - G67-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G67-6 (CANH) - G67-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G67-9 (CANH) - G67-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (No. 2 CAN junction connector CAN main wire) B
NG (Combination meter assembly CAN main wire) C
NG (Central gateway ECU [network gateway ECU] CAN branch wire) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

4.CONNECT CONNECTOR

D

6.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the G67 No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)
5.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)
a.
C221258C15
1.521,0.333 1.927,0.615 0.406,0.281 1.125,1.979 1.292,1.979 1.292,1.979 1.385,1.354 true 0.917,1.76 1.063,1.76 1.063,1.76 1.313,1.333 true 0.073,0.052 0.24,0.24 0.167,0.188 10 false *a 0.49,1.688 0.917,1.844 0.427,0.156 10 false CANH 0.708,1.906 1.104,2.063 0.396,0.156 10 false CANL 1.625,0.385 1.948,0.573 0.323,0.188 10 false G9
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-36 (CANH) - G9-35 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)

6.CONNECT CONNECTOR
a.

Reconnect the G67 No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
7.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
a.
C343190C72
1.448,0.396 1.927,0.698 0.479,0.302 1.188,1.771 1.333,1.771 1.333,1.771 1.667,1.292 true 1.323,1.979 1.469,1.979 1.469,1.979 1.781,1.292 true 1.521,0.479 2.135,0.677 0.615,0.198 10 false G128 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.76,1.688 1.375,1.885 0.615,0.198 10 false CA4L 0.927,1.906 1.542,2.104 0.615,0.198 10 false CA4H
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G128-18 (CA4H) - G128-17 (CA4L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 1 CAN JUNCTION CONNECTOR)

8.CONNECT CONNECTOR
a.

Reconnect the G68 No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR OPEN IN CAN BUS WIRE (ECM)
9.CHECK FOR OPEN IN CAN BUS WIRE (ECM)
a.
C317098C10
1.458,0.823 1.906,1.104 0.448,0.281 0.667,1.885 0.813,1.885 0.813,1.885 1.063,2.094 true 0.677,2.906 0.823,2.906 0.823,2.906 1.073,2.344 true 1.563,0.896 2.021,1.094 0.458,0.198 10 false G85 0.208,1.792 0.688,1.99 0.479,0.198 10 false CANH 0.24,2.823 0.688,3.021 0.448,0.198 10 false CANL 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-17 (CANH) - G85-28 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ECM - NO. 2 CAN JUNCTION CONNECTOR)