Use the following procedure to troubleshoot the lighting system.
*: Use the GTS
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage with the ignition switch off.
11 to 14 V
If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/ VSC | A |
| w/ ABS | B |
A
B
Use the GTS to check if the vehicle stability control system is functioning normally.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Vehicle stability control system DTCs are not output | A |
| Vehicle stability control system DTCs are output | B |
A
B
Use the GTS to check if the meter/gauge system is functioning normally.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Meter/gauge system DTCs are not output (for LED Headlight) | A |
| Meter/gauge system DTCs are not output (for Halogen Headlight) | B |
| Meter/gauge system DTCs are output | C |
A
B
C
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Use the GTS to check if the CAN communication system is functioning normally.
for LHD with Central Gateway ECU:
for RHD with Central Gateway ECU:
for LHD without Central Gateway ECU:
for RHD without Central Gateway ECU:
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output (for LHD with Central Gateway ECU) | B |
| CAN communication system DTCs are output (for RHD with Central Gateway ECU) | C |
| CAN communication system DTCs are output (for LHD without Central Gateway ECU) | D |
| CAN communication system DTCs are output (for RHD without Central Gateway ECU) | E |
A
B
C
D
E
Check for DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC output does not reoccur | A |
| DTC output reoccurs | B |
A
B
Refer to Problem Symptoms Table.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
A
B
Operation Check.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>OPERATION CHECK
Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU
Data List / Active Test.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Use the GTS to check if the anti-lock brake system is functioning normally.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Anti-lock brake system DTCs are not output | A |
| Anti-lock brake system DTCs are output | B |
A
B