CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY, BODY ECU (w/ Automatic Light Control System)
Remove the body ECU from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
| *1 | Instrument Panel Junction Block Assembly (for LHD) | - | - |
| *1 | Instrument Panel Junction Block Assembly (for RHD) | - | - |
| *1 | Body ECU | - | - |
Connect the instrument panel junction block assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: w/o Stop and Start System *2: w/ Stop and Start System |
||||
| A-6 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| A-7 (IG) - Body ground | - | Ignition power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V*1
10.5 to 16 V*2 |
|||
| A-1 (GND) - Body ground | - | Ground | Always | Below 1 Ω |
Install the body ECU to the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>INSTALLATION
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>INSTALLATION
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*: w/ Front Fog Light |
||||
| G27-1 (TRLY) - Body ground | P - Body ground | Tail light relay (TAIL) drive output | Taillights on | Below 2 V |
| Taillights off | 11 to 14 V | |||
| G28-5 (CLTB) - G28-3 (CLTE) | W - P | Automatic light control sensor power supply output | Headlight dimmer switch (light control switch) in AUTO position | 11 to 14 V |
| G28-6 (A) - Body ground | Y - Body ground | Headlight dimmer switch (light control switch) AUTO signal input | Headlight dimmer switch (light control switch) not in AUTO position | 11 to 14 V |
| Headlight dimmer switch (light control switch) in AUTO position | Below 1 V | |||
| G28-7 (TAIL) - Body ground | P - Body ground | Headlight dimmer switch (light control switch) tail signal input | Headlight dimmer switch (light control switch) in neither tail nor head position | 11 to 14 V |
| Headlight dimmer switch (light control switch) in tail or head position | Below 1 V | |||
| G28-8 (HEAD) - Body ground | B - Body ground | Headlight dimmer switch (light control switch) head signal input | Headlight dimmer switch (light control switch) not in head position | 11 to 14 V |
| Headlight dimmer switch (light control switch) in head position | Below 1 V | |||
| G28-10 (FFOG) - Body ground* | GR - Body ground | Front fog light switch input | Front fog light switch off | 11 to 14 V |
| Front fog light switch on | Below 1 V | |||
| G28-13 (HF) - Body ground | V - Body ground | Headlight dimmer switch high flash signal input | Headlight dimmer switch not in high flash position | 11 to 14 V |
| Headlight dimmer switch in high flash position | Below 1 V | |||
| G28-14 (HU) - Body ground | SB - Body ground | Headlight dimmer switch high signal input | Headlight dimmer switch in low position | 11 to 14 V |
| Headlight dimmer switch in high position | Below 1 V | |||
| 2P-12 (FFGO) - Body ground* | GR - Body ground | Front fog light signal output | Headlight dimmer switch (light control switch) in tail or head position and front fog light switch off | 11 to 14 V |
| Headlight dimmer switch (light control switch) in tail or head position and front fog light switch on | Below 1 V | |||
| 2Q-4 (HRLY) - Body ground | V - Body ground | Headlight relay (H-LP) drive output | Headlight dimmer switch (light control switch) in head position | Below 1 V |
| Headlight dimmer switch (light control switch) not in head position | 11 to 14 V | |||
| 2Q-5 (DIM) - Body ground | SB - Body ground | Headlight dimmer relay (DIMMER) drive output | Headlight dimmer switch (dimmer switch) in high or high flash position | Below 1 V |
| Headlight dimmer switch (dimmer switch) not in high or high flash position | 11 to 14 V | |||
Measure the voltage and check the waveform between each connector terminal using an oscilloscope according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G28-4 (CLTS) - Body ground | LG - Body ground | Automatic light control sensor signal input | Ignition switch ON, headlight dimmer switch (light control switch) in AUTO position and automatic light control sensor covered with a hand → Automatic light control sensor exposed to ambient light | Pulse generation
(waveform varies depending on light volume) |
| 2L-4 (DCTY) - Body ground | R - Body ground | Driver door courtesy light switch input | Driver door open | Below 1 V |
| Driver door closed | Pulse generation |
CHECK COMBINATION METER ASSEMBLY
Disconnect the G9, G10 and G11 combination meter assembly connectors.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: w/o Stop and Start System *2: w/ Stop and Start System |
||||
| G9-21 (B) - Body ground | W - Body ground | Battery power supply | Always | 11 to 14 V |
| G9-22 (IG+) - Body ground | Y - Body ground | Ignition power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V*1
10.5 to 16 V*2 |
|||
| G11-7 (B) - Body ground | L - Body ground | Battery power supply | Always | 11 to 14 V |
| G9-27 (EP) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| G10-20 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G9, G10 and G11 combination meter assembly connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: w/ Fron Fog Light *2: w/ Daytime Running Light |
||||
| G11-2 (HAZ) - Body ground | SB - Body ground | Clock assembly (hazard warning switch) signal input | Clock assembly (hazard warning switch) off | 11 to 14 V |
| Clock assembly (hazard warning switch) on | Below 1 V | |||
| G11-3 (SW) - Body ground | R - Body ground | Turn signal switch (full turn position) signal input | Ignition switch ON
Turn signal switch off |
11 to 14 V |
| Ignition switch ON
Turn signal switch in full turn position |
Below 1 V | |||
| G11-4 (ER) - Body ground | P - Body ground | Turn signal switch (right turn position) signal input | Ignition switch ON
Turn signal switch off |
11 to 14 V |
| Ignition switch ON
Turn signal switch in right turn position |
Below 1 V | |||
| G11-5 (EL) - Body ground | BE - Body ground | Turn signal switch (left turn position) signal input | Ignition switch ON
Turn signal switch off |
11 to 14 V |
| Ignition switch ON
Turn signal switch in left turn position |
Below 1 V | |||
| G11-8 (LL) - Body ground | Y - Body ground | LH turn signal light signal output | Ignition switch ON
LH turn signal light off |
Below 1 V |
| Ignition switch ON
LH turn signal light blinking |
Below 1 V ←→ 11 to 14 V | |||
| G11-13 (LR) - Body ground | SB - Body ground | RH turn signal light signal output | Ignition switch ON
RH turn signal light off |
Below 1 V |
| Ignition switch ON
RH turn signal light blinking |
Below 1 V ←→ 11 to 14 V | |||
| G10-1 (FOG) - Body ground*1 | P - Body ground | Front fog light signal | Ignition switch ON, front fog light switch on | 11 to 14 V |
| Ignition switch ON, front fog light switch off | Below 1 V | |||
| G10-11 (DRLE) - Body ground*2 | G - Body ground | Running light relay (DRL) drive output | Daytime running light on | Below 1 V |
| Daytime running light off | 11 to 14 V | |||
CHECK HEADLIGHT LEVELING ECU ASSEMBLY (for LED Headlight)
Disconnect the G80 headlight leveling ECU assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G80-1 (IG) - Body ground | G - Body ground | Ignition power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | |||
| G80-9 (E1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G80 headlight leveling ECU assembly connector.
Measure the voltage and check the waveform between each connector terminal using an oscilloscope according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G80-2 (RLEW) - Body ground | R - Body ground | RH side LED headlight signal input | Headlight dimmer switch off | Below 1 V |
| Headlight dimmer switch (light control switch) in head position | Pulse generation | |||
| G80-3 (LLEW) - Body ground | L - Body ground | LH side LED headlight signal input | Headlight dimmer switch off | Below 1 V |
| Headlight dimmer switch (light control switch) in head position | Pulse generation |