Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2016.03
RM3250E _56 Audio / Visual / Telematics _038052 AUDIO / VIDEO _0182296 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B158F  AV Signal Stoppage (Low Battery Voltage)  


DESCRIPTION

This DTC is stored when a video or audio signal is interrupted due to battery voltage input to the radio and display receiver assembly dropping temporarily.

DTC No. Detection Item DTC Detection Condition Trouble Area
B158F AV Signal Stoppage (Low Battery Voltage) A video or audio signal is interrupted when the battery voltage drops.
·

Harness or connector

·

Radio and display receiver assembly



WIRING DIAGRAM

E317088E02
0.573,0.615 2.646,0.813 2.073,0.198 10 false from Engine Stop and Start ECU 3.896,0.469 4.115,0.656 0.219,0.188 10 false *1 1.771,0.979 2.615,1.219 0.844,0.24 10 false from Battery 3.917,0.854 4.135,1.042 0.219,0.188 10 false *2 3.375,1.146 4.01,1.344 0.635,0.198 10 false RADIO 5.135,0.854 5.313,1.042 0.177,0.188 10 false 4 5.344,0.948 5.719,1.167 0.375,0.219 10 false +B1 5.104,1.885 5.479,2.104 0.375,0.219 10 false G40 5.104,2.073 6.823,2.458 1.719,0.385 10 false Radio and Display Receiver Assembly 0.188,2.146 2.125,2.385 1.938,0.24 10 false *1: w/ Stop and Start System 0.188,2.458 2.125,2.698 1.938,0.24 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>PARTS LOCATION


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E268487

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>OPERATION CHECK


b.

Measure the battery voltage.

Standard voltage:

11 to 14 V (w/o Stop and Start System)

10.5 to 16 V (w/ Stop and Start System)


HINT:

This display is updated once per second.



Result:
Proceed to
OK
NG



OK

2.CHECK DTC

NG

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY)
2.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY)
a.
E277492C44
1.427,0.25 1.885,0.51 0.458,0.26 2.281,0.969 2.521,0.594 2.521,0.594 2.771,0.594 true 2.813,0.479 3.177,0.729 0.365,0.25 10 false +B1 1.51,0.313 2.01,0.552 0.5,0.24 10 false G40 0.177,0.104 0.49,0.26 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G40-4 (+B1) - Body ground*1 Always 11 to 14 V
G40-4 (+B1) - Body ground*2 Always 10.5 to 16 V


*1: w/o Stop and Start System

*2: w/ Stop and Start System



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR