Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO RECEIVER › from 2016.03
RM3250E _56 Audio / Visual / Telematics _038052 AUDIO / VIDEO _0182780 RADIO RECEIVER A

AUDIO / VIDEO  RADIO RECEIVER  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the radio receiver removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)

CAUTION:
B414214

w/ Airbag System:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 45100 3.REMOVE STEERING WHEEL ASSEMBLY

Hide 55470 4.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Hide 55041B 5.REMOVE NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY

Hide 55410C 6.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

Hide 55905J 7.REMOVE CONTROL KNOB SUB-ASSEMBLY (for Manual Cooler System)

Hide 55918A 8.REMOVE AIR INLET DAMPER CONTROL LEVER (for Manual Cooler System)

Hide 84013A 9.REMOVE INTEGRATION PANEL SUB-ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Manual Cooler System)

Hide 55906A 10.DISCONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Cooler System)

Hide 55908A 11.DISCONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Cooler System)

Hide 55905J 12.REMOVE CONTROL KNOB SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55918A 13.REMOVE AIR INLET DAMPER CONTROL LEVER (for Manual Air Conditioning System)

Hide 84013A 14.REMOVE INTEGRATION PANEL SUB-ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Manual Air Conditioning System)

Hide 55906A 15.DISCONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55908A 16.DISCONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55909A 17.DISCONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55900 18.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 86120 19.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)

a.
E320279C01
0,0 0,0 false
V113146

Place Hands Here


Remove the 4 screws.


b.

Pull out the radio receiver assembly to detach the clips on the backside of the radio receiver assembly with bracket.


c.

Disconnect all the connectors and remove the radio receiver assembly with bracket.


Hide 86211 20.REMOVE NO. 1 RADIO BRACKET (for Radio Receiver Type)

a.
E320280

Remove the 2 screws.


b.
E320281

Remove the 3 screws and No. 1 radio bracket from the radio receiver assembly.


Hide 86212 21.REMOVE NO. 2 RADIO BRACKET (for Radio Receiver Type)

a.
E320282

Remove the 2 screws.


b.
E320283

Remove the 3 screws and No. 2 radio bracket from the radio receiver assembly.


Hide 86120 22.REMOVE RADIO RECEIVER ASSEMBLY (for Radio Receiver Type)

a.
E320284C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the radio receiver assembly in the direction of the arrow shown in the illustration.


Hide 86140A 23.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)

a.
E322737C04
0,0 0,0 false
V113146

Place Hands Here


Remove the 4 screws.


b.

Pull out the radio and display receiver assembly to detach the clips on the backside of the radio and display receiver assembly with bracket.


c.

Disconnect all the connectors and remove the radio and display receiver assembly with bracket.


Hide 86211 24.REMOVE NO. 1 RADIO BRACKET (for Radio and Display Type)

a.
E320240

Remove the 2 screws.


b.
E320241

Remove the 3 screws and No. 1 radio bracket from the radio and display receiver assembly.


Hide 86212 25.REMOVE NO. 2 RADIO BRACKET (for Radio and Display Type)

a.
E320242

Remove the 2 screws.


b.
E320243

Remove the 3 screws and No. 2 radio bracket from the radio and display receiver assembly.


Hide 86140A 26.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)

a.
E322739C02
0,0 0,0 false
V113147

Remove in this Direction


Remove the radio and display receiver assembly in the direction of the arrow shown in the illustration.