A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
53294C
1.INSTALL RADIATOR SIDE DEFLECTOR LH
|
Install in this Direction |
w/ Intercooler:
Attach the claw to install the radiator side deflector LH as shown in the illustration.
|
Install in this Direction |
w/o Intercooler:
Attach the claw to install the radiator side deflector LH as shown in the illustration.
53293C
2.INSTALL RADIATOR SIDE DEFLECTOR RH
Use the same procedure described for the LH side.
52116A
3.INSTALL FRONT BUMPER SIDE SUPPORT LH (for Standard Body)
|
Install in this Direction |
Attach the claw to install the front bumper side support LH as shown in the illustration.
Install the 2 clips and bolt.
52115A
4.INSTALL FRONT BUMPER SIDE SUPPORT RH (for Standard Body)
Use the same procedure described for the LH side.
52116A
5.INSTALL FRONT BUMPER SIDE SUPPORT LH (for Wide Body)
|
Install in this Direction |
Attach the claw to install the front bumper side support LH as shown in the illustration.
Install the 3 clips and bolt.
52115A
6.INSTALL FRONT BUMPER SIDE SUPPORT RH (for Wide Body)
Use the same procedure described for the LH side.
52124B
7.INSTALL FRONT BUMPER REINFORCEMENT PLATE LH
|
Install in this Direction |
Attach the guide to install the front bumper reinforcement sub-assembly as shown in the illustration.
Install the bolt.
52123B
8.INSTALL FRONT BUMPER REINFORCEMENT PLATE RH
Use the same procedure described for the LH side.
52021
9.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
|
Install in this Direction |
Attach the guide to install the front bumper reinforcement sub-assembly as shown in the illustration.
Install the 4 bolts.
52140
10.INSTALL FRONT BUMPER SIDE MOUNTING BRACKET ASSEMBLY LH
Install the front bumper side mounting bracket assembly LH with the 2 bolts.
52130
11.INSTALL FRONT BUMPER SIDE MOUNTING BRACKET ASSEMBLY RH
Use the same procedure described for the LH side.
52103
12.INSTALL FRONT BUMPER BRACKET SUB-ASSEMBLY LH
| *a | matchmark |
Align the matchmark on the front bumper bracket sub-assembly LH and vehicle body.
Install the front bumper bracket sub-assembly LH with the 4 bolts.
52102
13.INSTALL FRONT BUMPER BRACKET SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
14.INSTALL FRONT BUMPER ASSEMBLY
| *A | for Standard Body |
| *B | for Wide Body |
|
Install in this Direction |
Attach the guide to install the front bumper assembly as shown in the illustration.
w/ Fog Light:
Connect the connector.
| *A | for Standard Body |
| *B | for Wide Body |
Install the 8 bolts.
| *A | for Standard Body |
| *B | for Wide Body |
Install the 4 bolts.
53892G
15.INSTALL FRONT FENDER SPLASH SHIELD FRONT SEAL LH
53891J
16.INSTALL FRONT FENDER SPLASH SHIELD FRONT SEAL RH
Use the same procedure described for the LH side.
52119A
17.INSTALL FRONT BUMPER COVER
| *A | for Standard Body |
| *B | for Wide Body |
|
Protective Tape |
Put protective tape around the front bumper cover.
| *A | for Standard Body |
| *B | for Wide Body |
|
Install in this Direction |
Install the front bumper cover as shown in the illustration.
w/ Pre-crash Safety System:
Connect the connector.
|
Install in this Direction |
for Standard Body:
Attach the claw as shown in the illustration.
Use the same procedure for the claw on the other side.
|
Install in this Direction |
for Wide Body:
Attach the claw as shown in the illustration.
Use the same procedure for the claw on the other side.
Install the 3 screws.
| *a | Bolt |
| *b | Screw |
Install the 2 screws and 2 bolts.
Remove the protective tape.
| *A | for Standard Body |
| *B | for Wide Body |
Install the clip.
Use the same procedure for the clip on the other side.
53117C
18.INSTALL NO. 1 RADIATOR GRILLE RETAINER
19.ADJUST FOG LIGHT AIMING