Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _037980 CRUISE CONTROL _0262560 LANE DEPARTURE ALERT SYSTEM J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the forward recognition camera.

WIRING DIAGRAM

B437481E07
5.021,2.5 7.021,2.719 2,0.219 10 false Forward Recognition Camera 5.01,2.333 5.469,2.531 0.458,0.198 10 false Q4 5.573,2.083 6.031,2.281 0.458,0.198 10 false GND 5.594,0.771 6,1.031 0.406,0.26 10 false IGB 5.406,0.656 5.563,0.854 0.156,0.198 10 false 7 5.344,1.969 5.656,2.167 0.313,0.198 10 false 10 0.854,1.333 2.99,1.552 2.135,0.219 10 false from Engine Stop and Start ECU 0.177,3.073 2.177,3.302 2,0.229 10 false *1: w/o Stop and Start System 0.177,3.365 2.177,3.594 2,0.229 10 false *2: w/ Stop and Start System 1.323,0.771 4.385,0.969 3.063,0.198 10 false from IG Circuit 3.344,0.927 4.417,1.104 1.073,0.177 10 false IG1 NO. 5 4.156,0.667 4.469,0.865 0.313,0.198 10 false *1 4.167,1.219 4.479,1.417 0.313,0.198 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

w/o Stop and Start System:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.
A380142C08
1.521,0.167 1.875,0.417 0.354,0.25 0.917,1.542 1.26,1.385 true 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.604,0.208 1.917,0.406 0.313,0.198 10 false Q4 0.646,1.469 1.104,1.667 0.458,0.198 10 false IGB
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Q4-7 (IGB) - Body ground Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2


*1: w/o Stop and Start System

*2: w/ Stop and Start System



c.

Connect the forward recognition camera connector.


Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG (w/ Stop and Start System)

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)
a.
A380142C09
1.521,0.167 1.875,0.417 0.354,0.25 1.698,1.802 1.792,1.438 true 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.615,0.219 1.927,0.417 0.313,0.198 10 false Q4 1.563,1.823 2.021,2.021 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q4-10 (GND) - Body ground Always Below 1 Ω



c.

Connect the forward recognition camera connector


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR