88211B
1.PREPARATION FOR MILLIMETER WAVE RADAR SENSOR ASSEMBLY ADJUSTMENT
| *a | 5 m (16.4 ft.) |
| *b | 6 m (19.7 ft.) |
| *c | 4 m (13.1 ft.) |
| *d | 2 m (6.56 ft.) |
|
Do not place any metal objects in this area |
|
Do not place metal objects with a height of more than 50 mm in this area |
Park the vehicle on a level surface where the area in front of the vehicle shown in the illustration is free of metal objects.
Do not place metal objects with a height of more than 50 mm in this area
Adjust the tire inflation pressure to the specified pressure.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Clean the front emblem or millimeter wave radar sensor assembly.
Visually inspect the front of the vehicle.
Confirm that there is no damage or deformation.
Visually inspect the front bumper assembly, radiator grille and stays.
Confirm that there is no damage or deformation.
88211B
2.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY
| *a | SST(Reflector) |
Adjust SST (reflector) height.
Adjust the reflector so that the center of SST (reflector) is the same height as the millimeter wave radar sensor assembly.
Make sure to align the center of SST (reflector) with the millimeter wave radar sensor (the center of the emblem).
963 mm (37.9 in.)
Place SST (reflector).
for A Deck:
Hang a weight with a pointed tip from the center of the tail gate handle, and mark the rear center point of the vehicle (point A) on the ground.
| *a | String | *b | Weight |
| *c | Center | - | - |
Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.
for J Deck:
Hang a weight with a pointed tip from the center of the center stop light assembly, and mark the rear center point of the vehicle (point A) on the ground.
| *a | String | *b | Weight |
| *c | Center | *d | Bilateral Symmetry |
Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.
Hang a weight with a pointed tip from the center of the front emblem, and mark the front center point of the vehicle (point B) on the ground.
| *a | String | *b | Weight |
| *c | Center | - | - |
Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.
Using tape and a string, create a line that connects point B to point A and extends at least 3000 mm (9.84 ft.) beyond the front center point of the vehicle.
| *a | String | *b | Tape |
| *c | 3000 mm (9.84 ft.) | - | - |
Make sure the string is taut when securing it with tape.
Lightly flick the string with your fingers several times to confirm that the string is aligned with point B.
Mark point C (SST (reflector) placement position) at a position 3000 mm (9.84 ft.) from point B.
Place SST (reflector) at point C.
Front Beam Axis Adjustment:
Ensure that nobody enters the adjustment area during the adjustment.
Do not turn off the GTS or ignition switch.
Do not move or shake the vehicle during adjustment (do not get in or out of the vehicle).
Close all of the doors.
Connect the GTS to the DLC3.
Turn the ignition switch on (IG).
Enter the following menus:
| Tester Display |
|---|
| Front Beam Axis Adjustment |
According to the display on the GTS, press "Next".
Perform the adjustment according to the display on the GTS.
If an error code is displayed, perform troubleshooting according to the following table, then perform the adjustment again.
Press the "Exit" button to finish beam axis adjustment.
Front Beam Axis Misalignment Reading:
Ensure that nobody enters the adjustment area during the adjustment.
Do not turn off the GTS or engine switch.
Do not move or shake the vehicle during adjustment (do not get in or out of the vehicle).
Close all of the doors.
Enter the following menus:
| Tester Display |
|---|
| Front Beam Axis Misalignment Reading |
According to the display on the GTS, press "Next".
Perform the adjustment according to the display on the GTS.
| Vertical | -0.4 to 0.4 deg |
| Horizontal | -0.3 to 0.3 deg |
If the result is not as specified, perform beam axis adjustment again.
Front Beam Axis Offset Reading:
Enter the following menus:
| Tester Display |
|---|
| Front Beam Axis Offset Reading |
According to the display on the GTS, press "Next".
Perform the adjustment according to the display on the GTS.
| Vertical learning value | 0 deg |
| Horizontal learning value | 0 deg |
If the result is not as specified, perform beam axis adjustment again.
Turn the ignition switch off.
Disconnect the GTS from the DLC3.