Home › Suspension › TIRE / WHEEL › TIRE AND WHEEL SYSTEM › from 2016.03
RM3250E _53 Suspension _038043 TIRE / WHEEL _0187309 TIRE AND WHEEL SYSTEM G

TIRE / WHEEL  TIRE AND WHEEL SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT TIRES

a.

Check the tires for wear and proper inflation pressure.

Specified Pressure (When Tire is Cool):
Tire Size Model Unloaded Loaded
Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
205/70R15C 106/104S Single Cab
(Short Body)
240 (2.4, 35) 340 (3.4, 49) 240 (2.4, 35) 450 (4.5, 65)
Single Cab
(Long Body)
260 (2.6, 38) 330 (3.3, 48) 260 (2.6, 38) 450 (4.5, 65)
Smart Cab 260 (2.6, 38) 290 (2.9, 42) 260 (2.6, 38) 410 (4.1, 59)
Double Cab 260 (2.6, 38) 290 (2.9, 42) 260 (2.6, 38) 410 (4.1, 59)
215/65R16C 106/104S Single Cab
(Short Body)
240 (2.4, 35) 290 (2.9, 42) 240 (2.4, 35) 370 (3.7, 54)
Single Cab
(Long Body)
240 (2.4, 35) 290 (2.9, 42) 240 (2.4, 35) 370 (3.7, 54)
Smart Cab 240 (2.4, 35) 290 (2.9, 42) 240 (2.4, 35) 350 (3.5, 51)
Double Cab 240 (2.4, 35) 290 (2.9, 42) 240 (2.4, 35) 350 (3.5, 51)
205/R16C 8PR 110/108S 270 (2.7, 39) 270 (2.7, 39) 270 (2.7, 39) 340 (3.4, 49)
225/70R17C 108/106S 240 (2.4, 35) 240 (2.4, 35) 240 (2.4, 35) 300 (3.0, 44)
265/65R17 112S 200 (2.0, 29)
230 (2.3, 33)*1
200 (2.0, 29)
230 (2.3, 33)*1
200 (2.0, 29)
230 (2.3, 33)*1
250 (2.5, 36)
250 (2.5, 36)*1
265/60R18 110H 200 (2.0, 29)
230 (2.3, 33)*1
200 (2.0, 29)
230 (2.3, 33)*1
200 (2.0, 29)
230 (2.3, 33)*1
250 (2.5, 36)
250 (2.5, 36)*1


*1: for Europe (w/ Stop And Start System)


b.
C137874

Using a dial indicator, check the runout of the tires.

Tire runout:

3.0 mm (0.118 in.) or less


HINT:

Remove the wheel assembly from the vehicle, and measure the wheel assembly alone.



Hide 2.ROTATE TIRES

C237752C01
0.52,0.449 0.692,0.608 0.172,0.159 10 *a 0.52,2.168 0.692,2.326 0.172,0.159 10 *a 1.816,1.923 1.987,2.082 0.172,0.159 10 *c 1.807,0.185 1.979,0.343 0.172,0.159 10 *b
*a Front of the Vehicle
*b Vehicle Wheels and Spare Tire Wheel are Same Type
*c Vehicle Wheels are Aluminum but Spare Tire Wheel is Steel


a.

Remove the wheel assembly.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL>REMOVAL


b.

Rotate the tires as shown in the illustration.


c.

Install the wheel assembly.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL>INSTALLATION


Hide 3.INSPECT WHEEL BALANCE

a.
C264658N01
2.098,3.633 2.240,3.803 0.142,0.170 10 A

for Aluminum Wheel Type:

Check and adjust the off-the-car balance.

Tire Size Standard Imbalance after Adjustment
215/65R16C 106/104S 14 g (0.030 lb) or less
265/65R17 112S 13 g (0.028 lb) or less
265/60R18 110H 12 g (0.026 lb) or less

NOTICE:
·

Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.

·

Do not touch the sticking surface of the tape.

·

Adhere a sticking type balance weight to the flat surface (A) shown in the illustration.

Width (A):

25 mm (0.984 in.)


·

Push the balance weight firmly to adhere it to the position.

·

Do not reuse the balance weight.

·

Please use the Toyota genuine sticking type balance weight.



HINT:
·

The inner side balance weights should be installed by clipping them to the rim.

·

If the tires vibrate even after off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.




b.
C144019

for Steel Wheel Type:

Check and adjust the off-the-car balance.

Tire Size Standard Imbalance after Adjustment
205/70R15C 106/104S 14 g (0.030 lb) or less
215/65R16C 106/104S
205/R16C 8PR 110/108S
225/70R17C 108/106S 13 g (0.028 lb) or less
265/65R17 112S

HINT:

If the tires vibrate even after off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.



Hide 4.INSPECT FRONT AXLE HUB BEARING LOOSENESS (for 2WD)

Hide 5.INSPECT FRONT AXLE HUB RUNOUT (for 2WD)

Hide 6.INSPECT FRONT AXLE HUB BEARING LOOSENESS (for 4WD and Pre-Runner)

Hide 7.INSPECT FRONT AXLE HUB RUNOUT (for 4WD and Pre-Runner)