Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2016.03
RM3250E _58 Vehicle Interior _053993 PRE-CRASH SAFETY _0264409 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A63  Accelerator Pedal Position Sensor Circuit  


DESCRIPTION

The millimeter wave radar sensor assembly receives accelerator pedal position sensor signals from the ECM to determine if the accelerator pedal is being depressed. If the ECM detects a malfunction in the accelerator pedal position sensor, the millimeter wave radar sensor assembly is notified via CAN communication and stores DTC C1A63.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A63 Accelerator Pedal Position Sensor Circuit While the ignition switch to ON, the millimeter wave radar sensor assembly receives a throttle sensor malfunction signal from the ECM continuously for approximately 1.3 seconds or more.
·

ECD system

·

Millimeter wave radar sensor assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

The pre-crash safety system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (ECD SYSTEM)
HINT:

Pre-crash safety system DTC C1A63 may be stored due to a malfunction in the ECD system. Therefore, it is necessary to check for and troubleshoot ECD system DTCs first.


a.

Check for DTCs.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
ECD system DTCs are not output A
ECD system DTCs are output B



A

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

B

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A63 is not output A
DTC C1A63 is output B



A

B

3.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
3.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC (PRE-CRASH SAFETY SYSTEM)
4.CLEAR DTC (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

Result:
Proceed to
NEXT



NEXT

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)