Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY(for Double Cab) › from 2016.03
RM3250E _58 Vehicle Interior _038072 SEAT BELT _0185619 REAR SEAT OUTER BELT ASSEMBLY(for Double Cab) A

SEAT BELT  REAR SEAT OUTER BELT ASSEMBLY(for Double Cab)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 73370C 1.INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

a.
B440584C01
2.26,0.375 2.49,0.552 0.229,0.177 10 true *a 1.063,1.802 1.26,2 0.198,0.198 10 true *b 2.031,0.365 2.188,0.563 0.156,0.198 10 true 1 0.875,1.802 1.031,2 0.156,0.198 10 true 2
*a Bolt A
*b Bolt B


w/ Pretensioner:

i.

Attach the 2 guides and temporarily install the rear No. 1 seat outer belt assembly LH with the 2 bolts.


ii.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
for Bolt A : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
for Bolt B : 42.0 N*m (428 kgf*cm, 31 ft.*lbf)


iii.
B440586C01
0.969,0.542 1.219,0.344 false 1.271,0.25 1.583,0.406 0.313,0.156 10 false *1
*1 Locking Button


Connect the pretensioner connector and lock the locking button as shown in the illustration.



b.
B415712C01
1.156,0.427 1.385,0.625 0.229,0.198 10 true *a 1.021,1.844 1.24,2.104 0.219,0.26 10 true *b 0.917,0.438 1.073,0.635 0.156,0.198 10 true 1 0.781,1.833 0.938,2.031 0.156,0.198 10 true 2
*a Bolt A
*b Bolt B


w/o Pretensioner:

i.

Attach the 2 guides and install the rear No. 1 seat outer belt assembly LH with the 2 bolts.


ii.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
for Bolt A : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
for Bolt B : 42.0 N*m (428 kgf*cm, 31 ft.*lbf)



c.
B415711

Connect the shoulder anchor of the rear No. 1 seat outer belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


d.
B415217C01
1.875,0.979 2.188,1.115 true 2.25,1.052 2.563,1.25 0.313,0.198 10 true *a
*a Mark
V100136

Front


Install the bolt and connect the floor anchor of the rear No. 1 seat outer belt assembly LH as shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


e.

Check that the ELR locks.

NOTICE:

The check should be performed with the rear No. 1 seat outer belt assembly LH installed.


i.

With the belt assembly installed, check that the belt locks when it is pulled out quickly.



Hide 62514A 2.INSTALL LOWER QUARTER TRIM PANEL LH

Hide 73178B 3.INSTALL SEAT BELT ANCHOR COVER CAP

Hide 5.INSTALL REAR SEAT ASSEMBLY

Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION