Home › Audio / Visual / Telematics › AUDIO / VIDEO › STEREO JACK ADAPTER ASSEMBLY › from 2016.03
RM3250E _56 Audio / Visual / Telematics _038052 AUDIO / VIDEO _0182787 STEREO JACK ADAPTER ASSEMBLY A

AUDIO / VIDEO  STEREO JACK ADAPTER ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the stereo jack adapter removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)

CAUTION:
B414214

w/ Airbag System:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 45100 3.REMOVE STEERING WHEEL ASSEMBLY

Hide 55410C 4.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

Hide 55905J 5.REMOVE CONTROL KNOB SUB-ASSEMBLY (for Manual Cooler System)

Hide 55918A 6.REMOVE AIR INLET DAMPER CONTROL LEVER (for Manual Cooler System)

Hide 84013A 7.REMOVE INTEGRATION PANEL SUB-ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Manual Cooler System)

Hide 55906A 8.DISCONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Cooler System)

Hide 55908A 9.DISCONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Cooler System)

Hide 55905J 10.REMOVE CONTROL KNOB SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55918A 11.REMOVE AIR INLET DAMPER CONTROL LEVER (for Manual Air Conditioning System)

Hide 84013A 12.REMOVE INTEGRATION PANEL SUB-ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Manual Air Conditioning System)

Hide 55906A 13.DISCONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55908A 14.DISCONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55909A 15.DISCONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55900 16.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 33504F 17.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 58804A 18.REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (w/ Console Box Lid)

Hide 58818A 19.REMOVE FRONT CONSOLE BOX COVER (w/o Console Box Lid)

Hide 58811A 20.REMOVE FRONT CONSOLE BOX (w/o Console Box Lid)

Hide 55407C 21.REMOVE LOWER INSTRUMENT COVER SUB-ASSEMBLY

Hide 86190C 22.REMOVE NO. 1 STEREO JACK ADAPTER ASSEMBLY

a.
E322698C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claws and remove the No. 1 stereo jack adapter assembly.


Hide 55303B 23.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 86203 24.REMOVE RADIO WIRE

E322699

a.

Detach the clamps and remove the radio wire.