Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(for Type C) › from 2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0265842 AIRBAG SYSTEM(for Type C) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Type C)  B181A/7A  Short in Passenger Side Airbag Variable Vent Hole Squib Circuit  B181B/7A  Open in Passenger Side Airbag Variable Vent Hole Squib Circuit  B181C/7A  Short to GND in Passenger Side Airbag Variable Vent Hole Squib Circuit  B181D/7A  Short to B+ in Passenger Side Airbag Variable Vent Hole Squib Circuit  


DESCRIPTION

The front passenger side airbag variable vent hole squib circuit consists of the airbag sensor assembly and instrument panel passenger airbag assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side airbag variable vent hole squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B181A/7A Short in Passenger Side Airbag Variable Vent Hole Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the front passenger side airbag variable vent hole squib circuit during the primary check.

·

An instrument panel passenger airbag assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly

·

Airbag sensor assembly


B181B/7A Open in Passenger Side Airbag Variable Vent Hole Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the front passenger side airbag variable vent hole squib circuit for 2 seconds.

·

An instrument panel passenger airbag assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly

·

Airbag sensor assembly


B181C/7A Short to GND in Passenger Side Airbag Variable Vent Hole Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the front passenger side airbag variable vent hole squib circuit for 0.5 seconds.

·

An instrument panel passenger airbag assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly

·

Airbag sensor assembly


B181D/7A Short to B+ in Passenger Side Airbag Variable Vent Hole Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the front passenger side airbag variable vent hole squib circuit for 0.5 seconds.

·

An instrument panel passenger airbag assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly

·

Airbag sensor assembly



WIRING DIAGRAM

C253311E49
1.146,0.917 1.635,1.167 0.49,0.25 10 false VHP+ 5.51,3.052 5.896,3.26 0.385,0.208 10 false G42 5.5,3.208 7.104,3.448 1.604,0.24 10 false Airbag Sensor Assembly 3.365,0.823 3.542,1.021 0.177,0.198 10 false 2 1.635,2.115 1.844,2.344 0.208,0.229 10 false 2 3.354,2 3.594,2.229 0.24,0.229 10 false 1 1.625,0.917 1.875,1.146 0.25,0.229 10 false 1 3.26,1.021 3.667,1.24 0.406,0.219 10 false GH2 3.271,2.219 3.74,2.427 0.469,0.208 10 false GH2 0.177,3.135 0.583,3.344 0.406,0.208 10 false H6 0.177,3.313 3.052,3.719 2.875,0.406 10 false Instrument Panel Passenger Airbag Assembly 5.813,1.01 6.302,1.26 0.49,0.25 10 false VHP+ 1.167,2.104 1.656,2.354 0.49,0.25 10 false VHP- 5.813,2.229 6.302,2.479 0.49,0.25 10 false VHP- 5.531,0.917 5.885,1.115 0.354,0.198 10 false 19 5.531,2.125 5.885,2.323 0.354,0.198 10 false 20 3.24,1.219 3.729,1.469 0.49,0.25 10 false VHP+ 3.26,2.427 3.75,2.677 0.49,0.25 10 false VHP-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DIAGNOSTIC TROUBLE CODE CHART).


PROCEDURE

1.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY
a.
C355013C01
0.615,2.365 1,2.583 0.385,0.219 2.469,2.281 2.135,2.146 false 2.365,2.833 1.917,2.583 true 1.906,0.656 2.063,0.854 0.156,0.198 10 false A 1.375,0.885 1.531,1.083 0.156,0.198 10 false C 1.219,0.885 1.375,1.083 0.156,0.198 10 false D 0.865,0.885 1.021,1.083 0.156,0.198 10 false E 0.635,0.885 0.792,1.083 0.156,0.198 10 false F 2.188,1.26 2.5,1.458 0.313,0.198 10 false *2 0.385,0.427 0.698,0.625 0.313,0.198 10 false *1 1.604,1.667 1.917,1.865 0.313,0.198 10 false *3 2.396,2.781 2.708,2.979 0.313,0.198 10 false *b 1.302,1.49 1.615,1.688 0.313,0.198 10 false *a 0.729,2.396 1.042,2.594 0.313,0.198 10 false H6 2.51,2.219 2.823,2.417 0.313,0.198 10 false *4
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly
*3 Connector E
*4 SST
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)
*b Color: Green


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the instrument panel passenger airbag assembly.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the instrument panel passenger airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is not output
DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is output


HINT:

Codes other than DTC B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector E.



DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is not output

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is output

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly.


b.
C208248C03
0.385,0.813 0.698,0.969 0.313,0.156 10 false *1 2.406,1.708 2.719,1.865 0.313,0.156 10 false *2 2.177,1.021 2.49,1.177 0.313,0.156 10 false A 1.74,1.354 2.052,1.51 0.313,0.156 10 false B 1.354,1.354 1.667,1.51 0.313,0.156 10 false C 1.208,1.354 1.521,1.51 0.313,0.156 10 false D 0.833,1.354 1.146,1.51 0.313,0.156 10 false E 0.563,1.354 0.875,1.51 0.313,0.156 10 false F 1,0.75 1.313,0.906 0.313,0.156 10 false *3 1.5,0.719 1.813,0.875 0.313,0.156 10 false *4
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire


Check that the connectors (on the airbag sensor assembly side and instrument panel passenger airbag assembly side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT

NG

REPLACE INSTRUMENT PANEL WIRE OR NO. 2 INSTRUMENT PANEL WIRE

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
a.
C355014C01
0.813,2.156 1.177,2.365 0.365,0.208 1.177,2.656 1.625,2.323 true 2.292,2.646 1.76,2.313 true 2.344,3.031 2.042,2.771 true 2.229,0.656 2.385,0.854 0.156,0.198 10 false A 1.479,0.917 1.635,1.115 0.156,0.198 10 false C 1.344,0.917 1.5,1.115 0.156,0.198 10 false D 1.844,0.917 2,1.115 0.156,0.198 10 false B 0.979,0.917 1.135,1.115 0.156,0.198 10 false E 0.76,0.917 0.917,1.115 0.156,0.198 10 false F 2.51,1.271 2.823,1.469 0.313,0.198 10 false *2 0.521,0.438 0.833,0.635 0.313,0.198 10 false *1 1.417,1.594 1.729,1.792 0.313,0.198 10 false *a 1.667,1.76 1.979,1.958 0.313,0.198 10 false *3 2.385,2.969 2.698,3.167 0.313,0.198 10 false *b 0.906,2.177 1.219,2.375 0.313,0.198 10 false H6 0.781,2.563 1.313,2.802 0.531,0.24 10 false VHP+ 2.344,2.573 2.875,2.813 0.531,0.24 10 false VHP-
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly
*3 Connector E
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)
*b Color: Green


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-1 (VHP+) - Body ground Ignition switch ON Below 1 V
H6-2 (VHP-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-1 (VHP+) - H6-2 (VHP-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-1 (VHP+) - H6-2 (VHP-) Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-1 (VHP+) - Body ground Always 1 MΩ or higher
H6-2 (VHP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
a.
C147154C08
0.49,0.677 0.802,0.833 0.313,0.156 10 false *1 2.083,1.438 2.396,1.594 0.313,0.156 10 false *2 1.323,1.125 1.635,1.281 0.313,0.156 10 false C 1.219,1.125 1.531,1.281 0.313,0.156 10 false D 0.854,1.125 1.167,1.281 0.313,0.156 10 false E 0.74,1.125 1.052,1.281 0.313,0.156 10 false F 1.885,0.854 2.26,1.156 0.375,0.302 10 false A
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly


Connect the connectors to the instrument panel passenger airbag assembly and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is not output
DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is output


HINT:

Codes other than DTC B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.




DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is not output

DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is output

5.CHECK INSTRUMENT PANEL WIRE
a.
C252990C07
0.313,2.438 0.698,2.708 0.385,0.271 1.396,2.896 0.802,3.094 true 1.594,2.906 2.469,3.063 true 0.385,0.563 0.698,0.719 0.313,0.156 10 false *1 0.948,0.563 1.26,0.719 0.313,0.156 10 false *2 1.448,0.552 1.76,0.708 0.313,0.156 10 false *3 2.188,1.302 2.5,1.458 0.313,0.156 10 false *4 1.552,1.99 1.865,2.146 0.313,0.156 10 false *5 1.083,1.781 1.396,1.938 0.313,0.156 10 false *a 0.375,2.49 0.792,2.708 0.417,0.219 10 false GH2 2.521,2.99 3.052,3.219 0.531,0.229 10 false VHP+ 0.438,3.01 0.958,3.24 0.521,0.229 10 false VHP- 2,0.76 2.208,0.948 0.208,0.188 10 false A 1.677,0.979 1.885,1.167 0.208,0.188 10 false B 1.354,0.99 1.563,1.177 0.208,0.188 10 false C 1.167,0.99 1.375,1.177 0.208,0.188 10 false D 0.844,0.99 1.052,1.177 0.208,0.188 10 false E 0.635,0.979 0.844,1.167 0.208,0.188 10 false F
*1 Instrument Panel Passenger Airbag Assembly
*2 No. 2 Instrument Panel Wire
*3 Instrument Panel Wire
*4 Airbag Sensor Assembly
*5 Connector C
*a Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
GH2-2 (VHP+) - Body ground Ignition switch ON Below 1 V
GH2-1 (VHP-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GH2-2 (VHP+) - GH2-1 (VHP-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DIAGNOSIS SYSTEM


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GH2-2 (VHP+) - GH2-1 (VHP-) Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GH2-2 (VHP+) - Body ground Always 1 MΩ or higher
GH2-1 (VHP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE