Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0265900 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1771  Passenger Side Buckle Switch Circuit Malfunction  


DESCRIPTION

The front passenger side buckle switch circuit consists of the occupant detection ECU and front seat inner belt assembly LH*1 and RH*2.

DTC B1771 is stored when a malfunction is detected in the front passenger side buckle switch circuit.

Troubleshoot DTC B1771 first when DTCs B1771 and B1795 are output simultaneously.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1771 Passenger Side Buckle Switch Circuit Malfunction
One of the following conditions is met:
·

Occupant detection ECU detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in the front passenger side buckle switch circuit for 2 seconds.

·

Front passenger side buckle switch malfunction.

·

Occupant detection ECU malfunction.


·

Front seat wire RH

·

Front seat inner belt assembly LH*1

·

Front seat inner belt assembly RH*2

·

Occupant detection ECU



·

*1: for RHD

·

*2: for LHD


HINT:
·

When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1771 of the occupant classification system.

·

Use the GTS to check for DTCs of the occupant detection ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

C253566E51
0.323,4.125 2.792,4.333 2.469,0.208 10 false Front Seat Inner Belt Assembly LH*1 5.635,3.917 6.688,4.146 1.052,0.229 10 false T10*1, S10*2 5.635,4.073 6.865,4.406 1.229,0.333 10 false Occupant Detection ECU 5.646,1.26 5.813,1.427 0.167,0.167 10 false 9 5.646,2.823 5.813,2.99 0.167,0.167 10 false 5 2.438,2.833 2.594,3.031 0.156,0.198 10 false 2 2.438,1.26 2.594,1.458 0.156,0.198 10 false 1 0.323,3.948 1.323,4.167 1,0.219 10 false T11*1, S11*2 5.823,1.375 6.646,1.719 0.823,0.344 10 false BSW 5.833,2.938 6.656,3.281 0.823,0.344 10 false BGND 2.229,1.25 2.604,1.51 0.375,0.26 10 false + 2.25,2.823 2.625,3.083 0.375,0.26 10 false - 0.323,4.427 2.792,4.635 2.469,0.208 10 false Front Seat Inner Belt Assembly RH*2 3.24,4.146 4.927,4.344 1.688,0.198 10 false *1: for RHD 3.26,4.427 4.948,4.625 1.688,0.198 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


HINT:
·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat LH*1 and RH*2 installation bolts to see the undersurface of the seat cushion.

·

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause a problem, such as seat rail deformation. Hold the seat up only for as long as necessary.

*1: for RHD

*2: for LHD




PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1771 is not output
DTC B1771 is output


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




DTC B1771 is not output

DTC B1771 is output

2.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the occupant detection ECU and front seat inner belt.


Result:
Proceed to
Connectors are properly connected
Connectors are not properly connected



Connectors are properly connected

3.CHECK CONNECTORS

Connectors are not properly connected

CONNECT CONNECTORS

3.CHECK CONNECTORS
a.
C253897C03
0.604,1.375 1.177,1.594 0.573,0.219 10 false *1 (*A) 2.51,1.646 2.708,1.813 0.198,0.167 10 false *3 1.417,1.146 1.99,1.365 0.573,0.219 10 false *4 (*A) 0.615,1.563 1.188,1.781 0.573,0.219 10 false *2 (*B) 1.427,1.344 2,1.563 0.573,0.219 10 false *5 (*B)
*A for RHD
*B for LHD
*1 Front Seat Inner Belt Assembly LH
*2 Front Seat Inner Belt Assembly RH
*3 Occupant Detection ECU
*4 Front Seat Wire LH
*5 Front Seat Wire RH


Disconnect the connectors from the occupant detection ECU and the front seat inner belt assembly LH*1 and RH*2.


b.

Check that the connectors (on the occupant detection ECU side and the front seat inner belt assembly LH*1 and RH*2 side) are not damaged.

·

*1: for RHD

·

*2: for LHD



Result:
Proceed to
Connectors are not deformed or damaged
Connectors are deformed or damaged (for RHD)
Connectors are deformed or damaged (for LHD)



Connectors are not deformed or damaged

4.CHECK DTC

Connectors are deformed or damaged (for RHD)

REPLACE FRONT SEAT WIRE LH

Connectors are deformed or damaged (for LHD)

REPLACE FRONT SEAT WIRE RH

4.CHECK DTC
a.

Connect the connectors to the occupant detection ECU and front seat inner belt assembly LH*1 and RH*2.

·

*1: for RHD

·

*2: for LHD



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1771 is not output
DTC B1771 is output (for RHD)
DTC B1771 is output (for LHD)


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




DTC B1771 is not output

DTC B1771 is output (for RHD)

5.CHECK FRONT SEAT WIRE LH

DTC B1771 is output (for LHD)

10.CHECK FRONT SEAT WIRE RH
5.CHECK FRONT SEAT WIRE LH
C350411C01
3.073,0.844 3.438,1.042 0.365,0.198 5.24,0.823 5.604,1.021 0.365,0.198 5.573,1.292 5.906,1 true 6.552,1.26 6.229,0.99 true 5.688,1.542 5.813,1.427 true 4.354,1.385 4,1.021 true 4.177,0.885 4.51,0.594 true 0.688,1.094 1,1.292 0.313,0.198 10 false *1 3.896,0.385 4.208,0.583 0.313,0.198 10 false *4 2.115,1.302 2.427,1.5 0.313,0.198 10 false *2 2.021,0.74 2.177,0.938 0.156,0.198 10 false A 1.656,0.969 1.813,1.167 0.156,0.198 10 false B 1.135,0.958 1.292,1.156 0.156,0.198 10 false C 0.76,0.719 0.917,0.917 0.156,0.198 10 false D 5.667,0.24 5.979,0.438 0.313,0.198 10 false *b 5.99,0.448 6.302,0.646 0.313,0.198 10 false *5 3.5,0.188 3.813,0.385 0.313,0.198 10 false *a 5.521,1.49 5.833,1.688 0.313,0.198 10 false *6 4.552,0.5 5.167,0.698 0.615,0.198 10 false BGND 4.406,1.313 5.021,1.51 0.615,0.198 10 false BSW 5.469,1.229 5.625,1.427 0.156,0.198 10 false - 6.604,1.188 6.76,1.385 0.156,0.198 10 false + 1.375,0.552 1.688,0.75 0.313,0.198 10 false *3 3.146,0.865 3.479,1.094 0.333,0.229 10 false T10 5.302,0.844 5.677,1.042 0.375,0.198 10 false T11
*1 Front Seat Inner Belt Assembly LH *2 Occupant Detection ECU
*3 Front Seat Wire LH *4 Connector B
*5 Connector C *6 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
T10-9 (BSW) - Body ground Ignition switch ON Below 1 V
T10-5 (BGND) - Body ground



b.

Turn the ignition switch off.


c.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


d.

Using service wires, connect terminals 1 (+) and 2 (-) of connector C.

NOTICE:

Do not forcibly insert the service wires into the terminals of the connector.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T10-9 (BSW) - T10-5 (BGND) Always Below 1 Ω



f.

Disconnect the service wires from connector C.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T10-9 (BSW) - T10-5 (BGND) Always 1 MΩ or higher
T10-9 (BSW) - Body ground
T10-5 (BGND) - Body ground



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT SEAT INNER BELT ASSEMBLY LH

NG

REPLACE FRONT SEAT WIRE LH

6.CHECK FRONT SEAT INNER BELT ASSEMBLY LH
a.

Replace the front seat inner belt assembly LH.

for Manual Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Manual Seat)>REMOVAL

for Power Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Power Seat)>REMOVAL

HINT:

Perform the inspection using parts from a normal vehicle when possible.



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1771 is not output
DTC B1771 is output


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




DTC B1771 is not output

END (FRONT SEAT INNER BELT ASSEMBLY LH WAS DEFECTIVE)

DTC B1771 is output

7.REPLACE OCCUPANT DETECTION ECU
7.REPLACE OCCUPANT DETECTION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL

HINT:

Perform the inspection using parts from a normal vehicle when possible.



d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


Result:
Proceed to
NEXT



NEXT

8.PERFORM ZERO POINT CALIBRATION
8.PERFORM ZERO POINT CALIBRATION

Result:
Proceed to
"Zero Point Calibration is complete." is displayed



"Zero Point Calibration is complete." is displayed

9.PERFORM SENSITIVITY CHECK
9.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
NEXT



NEXT

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)

10.CHECK FRONT SEAT WIRE RH
C350411C02
3.073,0.844 3.438,1.042 0.365,0.198 5.24,0.823 5.604,1.021 0.365,0.198 5.573,1.292 5.906,1 true 6.552,1.26 6.229,0.99 true 5.688,1.542 5.813,1.427 true 4.354,1.385 4,1.021 true 4.188,0.885 4.521,0.594 true 0.688,1.094 1,1.292 0.313,0.198 10 false *1 3.896,0.385 4.208,0.583 0.313,0.198 10 false *4 2.115,1.302 2.427,1.5 0.313,0.198 10 false *2 2.021,0.74 2.177,0.938 0.156,0.198 10 false A 1.656,0.969 1.813,1.167 0.156,0.198 10 false B 1.135,0.958 1.292,1.156 0.156,0.198 10 false C 0.76,0.719 0.917,0.917 0.156,0.198 10 false D 5.667,0.24 5.979,0.438 0.313,0.198 10 false *b 5.99,0.448 6.302,0.646 0.313,0.198 10 false *5 3.5,0.188 3.813,0.385 0.313,0.198 10 false *a 5.521,1.49 5.833,1.688 0.313,0.198 10 false *6 4.573,0.5 5.188,0.698 0.615,0.198 10 false BGND 4.406,1.323 5.021,1.521 0.615,0.198 10 false BSW 5.469,1.229 5.625,1.427 0.156,0.198 10 false - 6.604,1.188 6.76,1.385 0.156,0.198 10 false + 1.375,0.552 1.688,0.75 0.313,0.198 10 false *3 3.125,0.865 3.458,1.094 0.333,0.229 10 false S10 5.302,0.844 5.677,1.042 0.375,0.198 10 false S11
*1 Front Seat Inner Belt Assembly RH *2 Occupant Detection ECU
*3 Front Seat Wire RH *4 Connector B
*5 Connector C *6 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S10-9 (BSW) - Body ground Ignition switch ON Below 1 V
S10-5 (BGND) - Body ground



b.

Turn the ignition switch off.


c.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


d.

Using service wires, connect terminals 1 (+) and 2 (-) of connector C.

NOTICE:

Do not forcibly insert the service wires into the terminals of the connector.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S10-9 (BSW) - S10-5 (BGND) Always Below 1 Ω



f.

Disconnect the service wires from connector C.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S10-9 (BSW) - S10-5 (BGND) Always 1 MΩ or higher
S10-9 (BSW) - Body ground
S10-5 (BGND) - Body ground



Result:
Proceed to
OK
NG



OK

11.CHECK FRONT SEAT INNER BELT ASSEMBLY RH

NG

REPLACE FRONT SEAT WIRE RH

11.CHECK FRONT SEAT INNER BELT ASSEMBLY RH
a.

Replace the front seat inner belt assembly RH.

for Manual Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Manual Seat)>REMOVAL

for Power Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Power Seat)>REMOVAL

HINT:

Perform the inspection using parts from a normal vehicle when possible.



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1771 is not output
DTC B1771 is output


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




DTC B1771 is not output

END (FRONT SEAT INNER BELT ASSEMBLY RH WAS DEFECTIVE)

DTC B1771 is output

12.REPLACE OCCUPANT DETECTION ECU
12.REPLACE OCCUPANT DETECTION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL

HINT:

Perform the inspection using parts from a normal vehicle when possible.



d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


Result:
Proceed to
NEXT



NEXT

13.PERFORM ZERO POINT CALIBRATION
13.PERFORM ZERO POINT CALIBRATION

Result:
Proceed to
"Zero Point Calibration is complete." is displayed



"Zero Point Calibration is complete." is displayed

14.PERFORM SENSITIVITY CHECK
14.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
NEXT



NEXT

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)