Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0265900 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1782  Rear Occupant Classification Sensor LH Circuit Malfunction  


DESCRIPTION

The rear occupant classification sensor LH circuit consists of the occupant detection ECU and rear occupant classification sensor LH.

DTC B1782 is stored when a malfunction is detected in the rear occupant classification sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1782 Rear Occupant Classification Sensor LH Circuit Malfunction
One of the following conditions is met:
·

Occupant detection ECU detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in the rear occupant classification sensor LH circuit for 2 seconds.

·

Rear occupant classification sensor LH malfunction.

·

Occupant detection ECU malfunction.


·

Separate type front seat cushion spring assembly (Rear occupant classification sensor LH)*1

·

Front seat adjuster assembly RH (Rear occupant classification sensor LH)*2

·

Front seat wire LH*1

·

Front seat wire RH*2

·

Occupant detection ECU



·

*1: for RHD

·

*2: for LHD


HINT:
·

When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1782 of the occupant classification system.

·

Use the GTS to check for DTCs of the occupant detection ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

C239232E85
0.552,3.063 3.76,3.521 3.208,0.458 10 false Separate Type Front Seat Cushion Spring Assembly (Rear Occupant Classification Sensor LH) 5.344,3.073 7.073,3.448 1.729,0.375 10 false Occupant Detection ECU 5.385,0.615 5.896,0.948 0.51,0.333 10 false SVC3 5.385,1.479 5.865,1.781 0.479,0.302 10 false SIG3 5.385,2.365 5.917,2.646 0.531,0.281 10 false SGD3 1.844,0.521 2.177,0.969 0.333,0.448 10 false 1 1.844,1.396 2.125,1.771 0.281,0.375 10 false 2 1.844,2.271 2.167,2.646 0.323,0.375 10 false 3 5.198,0.521 5.521,0.719 0.323,0.198 10 false 5 5.198,1.385 5.417,1.667 0.219,0.281 10 false 9 5.198,2.24 5.458,2.448 0.26,0.208 10 false 3 5.344,2.906 5.708,3.115 0.365,0.208 10 false T9 0.552,2.906 1.052,3.24 0.5,0.333 10 false T7 1.438,0.625 1.948,0.948 0.51,0.323 10 false SVC 1.5,1.49 2.01,1.813 0.51,0.323 10 false SIG 1.458,2.354 1.958,2.615 0.5,0.26 10 false SGD 0.042,0.042 1.333,0.281 1.292,0.24 12 false for RHD:

C239232E86
0.552,3.063 3,3.479 2.448,0.417 10 false Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH) 5.344,3.073 7.073,3.448 1.729,0.375 10 false Occupant Detection ECU 5.385,0.615 5.896,0.948 0.51,0.333 10 false SVC3 5.385,1.479 5.865,1.781 0.479,0.302 10 false SIG3 5.385,2.365 5.917,2.646 0.531,0.281 10 false SGD3 1.844,0.521 2.177,0.969 0.333,0.448 10 false 1 1.844,1.396 2.125,1.771 0.281,0.375 10 false 2 1.844,2.271 2.167,2.646 0.323,0.375 10 false 3 5.208,0.521 5.531,0.719 0.323,0.198 10 false 5 5.198,1.385 5.417,1.667 0.219,0.281 10 false 9 5.198,2.24 5.458,2.448 0.26,0.208 10 false 3 5.344,2.906 5.708,3.115 0.365,0.208 10 false S9 0.552,2.906 1.052,3.24 0.5,0.333 10 false S13 1.438,0.625 1.948,0.948 0.51,0.323 10 false SVC 1.5,1.49 2.01,1.813 0.51,0.323 10 false SIG 1.458,2.354 1.958,2.615 0.5,0.26 10 false SGD 0.042,0.042 1.333,0.281 1.292,0.24 12 false for LHD:

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>GENERAL INFORMATION


HINT:
·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat LH*1 and RH*2 installation bolts to see the undersurface of the seat cushion.

·

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.

*1: for RHD

*2: for LHD




PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1782 is not output
DTC B1782 is output


HINT:

DTCs other than DTC B1782 may be output at this time, but they are not related to this check.




DTC B1782 is not output

DTC B1782 is output

2.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the occupant detection ECU and rear occupant classification sensor LH.


Result:
Proceed to
Connectors are properly connected
Connectors are not properly connected



Connectors are properly connected

3.CHECK CONNECTORS

Connectors are not properly connected

CHECK CONNECTORS

3.CHECK CONNECTORS
a.
C281859C04
0.74,1.625 1.052,1.823 0.313,0.198 10 false *1 2.583,1.51 2.896,1.708 0.313,0.198 10 false *2 1.469,1.375 2.063,1.594 0.594,0.219 10 false *3 (*A) 1.469,1.563 2.063,1.781 0.594,0.219 10 false *4 (*B)
*A for RHD
*B for LHD
*1 Rear Occupant Classification Sensor LH
*2 Occupant Detection ECU
*3 Front Seat Wire LH
*4 Front Seat Wire RH


Disconnect the connectors from the occupant detection ECU and rear occupant classification sensor LH.


b.

Check that the connectors (on the occupant detection ECU side and rear occupant classification sensor LH side) are not damaged.


Result:
Proceed to
Connectors are not deformed or damaged (for RHD)
Connectors are not deformed or damaged (for LHD)
Connectors are deformed or damaged (for RHD)
Connectors are deformed or damaged (for LHD)



Connectors are not deformed or damaged (for RHD)

4.CHECK FRONT SEAT WIRE LH

Connectors are not deformed or damaged (for LHD)

13.CHECK FRONT SEAT WIRE RH

Connectors are deformed or damaged (for RHD)

REPLACE FRONT SEAT WIRE LH

Connectors are deformed or damaged (for LHD)

REPLACE FRONT SEAT WIRE RH

4.CHECK FRONT SEAT WIRE LH
a.
C354989C03
0.563,3.813 0.938,4.021 0.375,0.208 0.625,2.219 1,2.427 0.375,0.208 2.115,1.833 2.323,1.719 false 1.156,2.979 1.365,2.865 false 1.167,3.604 1.667,3.813 true 1.188,4.271 1.656,3.969 true 1.906,3.813 2.417,3.542 true 2.302,0.76 2.458,0.958 0.156,0.198 10 false A 1.906,1.021 2.063,1.219 0.156,0.198 10 false B 1.323,1.01 1.479,1.208 0.156,0.198 10 false C 0.906,0.771 1.063,0.969 0.156,0.198 10 false D 1.563,0.583 1.875,0.781 0.313,0.198 10 false *1 0.823,1.198 1.135,1.396 0.313,0.198 10 false *2 2.51,1.083 2.823,1.281 0.313,0.198 10 false *3 2.365,1.625 2.677,1.823 0.313,0.198 10 false *4 1,2.906 1.313,3.104 0.313,0.198 10 false *4 2.375,2.25 2.688,2.448 0.313,0.198 10 false *5 2.385,3.813 2.698,4.01 0.313,0.198 10 false *6 1.167,1.563 1.479,1.76 0.313,0.198 10 false *a 1.135,3.281 1.448,3.479 0.313,0.198 10 false *b 0.74,2.25 1.198,2.448 0.458,0.198 10 false T7 0.677,3.833 1.135,4.031 0.458,0.198 10 false T9 0.75,3.521 1.365,3.719 0.615,0.198 10 false SGD3 0.844,4.198 1.458,4.396 0.615,0.198 10 false SIG3 2.458,3.458 3.073,3.656 0.615,0.198 10 false SVC3
*1 Front Seat Wire LH
*2 Rear Occupant Classification Sensor LH
*3 Occupant Detection ECU
*4 Service Wire
*5 Connector C
*6 Connector B
*a Front view of wire harness connector
(to Rear Occupant Classification Sensor LH)
*b Front view of wire harness connector (to Occupant Detection ECU)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
T9-5 (SVC3) - Body ground Ignition switch ON Below 1 V
T9-9 (SIG3) - Body ground
T9-3 (SGD3) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using service wires, connect terminals 1 (SVC) and 3 (SGD), and terminals 2 (SIG) and 3 (SGD) of connector C.

NOTICE:

Do not forcibly insert the service wires into the terminals of the connector.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T9-5 (SVC3) - T9-3 (SGD3) Always Below 1 Ω
T9-9 (SIG3) - T9-3 (SGD3)



h.

Disconnect the service wires from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T9-5 (SVC3) - T9-3 (SGD3) Always 1 MΩ or higher
T9-9 (SIG3) - T9-3 (SGD3)
T9-5 (SVC3) - T9-9 (SIG3)
T9-5 (SVC3) - Body ground
T9-9 (SIG3) - Body ground
T9-3 (SGD3) - Body ground



Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

REPLACE FRONT SEAT WIRE LH

5.CHECK DTC
a.

Connect the connectors to the occupant detection ECU and rear occupant classification sensor LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1782 is not output
DTC B1782 is output


HINT:

DTCs other than DTC B1782 may be output at this time, but they are not related to this check.




DTC B1782 is not output

DTC B1782 is output

6.REPLACE OCCUPANT DETECTION ECU
6.REPLACE OCCUPANT DETECTION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL

Result:
Proceed to
NEXT


HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

7.PERFORM ZERO POINT CALIBRATION
7.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.



Result:
Proceed to
"Zero Point Calibration is complete." is displayed
"Zero Point Calibration is complete." is not displayed



"Zero Point Calibration is complete." is displayed

8.PERFORM SENSITIVITY CHECK

"Zero Point Calibration is complete." is not displayed

10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (REAR OCCUPANT CLASSIFICATION SENSOR LH)
8.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
OK
NG



OK

9.CHECK DTC

NG

10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (REAR OCCUPANT CLASSIFICATION SENSOR LH)
9.CHECK DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1782 is not output
DTC B1782 is output


HINT:

DTCs other than DTC B1782 may be output at this time, but they are not related to this check.




DTC B1782 is not output

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)

DTC B1782 is output

10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (REAR OCCUPANT CLASSIFICATION SENSOR LH)
10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (REAR OCCUPANT CLASSIFICATION SENSOR LH)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the separate type front seat cushion spring assembly.

for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY

for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


HINT:

Perform the inspection using parts from a normal vehicle when possible.


Result:
Proceed to
NEXT



NEXT

11.PERFORM ZERO POINT CALIBRATION
11.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.



Result:
Proceed to
"Zero Point Calibration is complete." is displayed



"Zero Point Calibration is complete." is displayed

12.PERFORM SENSITIVITY CHECK
12.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
NEXT



NEXT

END (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY [REAR OCCUPANT CLASSIFICATION SENSOR LH] WAS DEFECTIVE)

13.CHECK FRONT SEAT WIRE RH
a.
C354989C04
0.563,3.813 0.938,4.021 0.375,0.208 0.625,2.219 1,2.427 0.375,0.208 2.115,1.833 2.323,1.719 false 1.156,2.979 1.365,2.865 false 1.167,3.604 1.667,3.813 true 1.188,4.271 1.656,3.969 true 1.906,3.813 2.417,3.542 true 2.302,0.76 2.458,0.958 0.156,0.198 10 false A 1.906,1.021 2.063,1.219 0.156,0.198 10 false B 1.323,1.01 1.479,1.208 0.156,0.198 10 false C 0.906,0.771 1.063,0.969 0.156,0.198 10 false D 1.563,0.583 1.875,0.781 0.313,0.198 10 false *1 0.823,1.198 1.135,1.396 0.313,0.198 10 false *2 2.51,1.083 2.823,1.281 0.313,0.198 10 false *3 2.365,1.625 2.677,1.823 0.313,0.198 10 false *4 1,2.906 1.313,3.104 0.313,0.198 10 false *4 2.375,2.25 2.688,2.448 0.313,0.198 10 false *5 2.385,3.813 2.698,4.01 0.313,0.198 10 false *6 1.167,1.563 1.479,1.76 0.313,0.198 10 false *a 1.135,3.281 1.448,3.479 0.313,0.198 10 false *b 0.698,2.25 1.156,2.448 0.458,0.198 10 false S13 0.677,3.833 1.135,4.031 0.458,0.198 10 false S9 0.75,3.521 1.365,3.719 0.615,0.198 10 false SGD3 0.844,4.198 1.458,4.396 0.615,0.198 10 false SIG3 2.458,3.458 3.073,3.656 0.615,0.198 10 false SVC3
*1 Front Seat Wire RH
*2 Rear Occupant Classification Sensor LH
*3 Occupant Detection ECU
*4 Service Wire
*5 Connector C
*6 Connector B
*a Front view of wire harness connector
(to Rear Occupant Classification Sensor LH)
*b Front view of wire harness connector (to Occupant Detection ECU)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S9-5 (SVC3) - Body ground Ignition switch ON Below 1 V
S9-9 (SIG3) - Body ground
S9-3 (SGD3) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using service wires, connect terminals 1 (SVC) and 3 (SGD), and terminals 2 (SIG) and 3 (SGD) of connector C.

NOTICE:

Do not forcibly insert the service wires into the terminals of the connector.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S9-5 (SVC3) - S9-3 (SGD3) Always Below 1 Ω
S9-9 (SIG3) - S9-3 (SGD3)



h.

Disconnect the service wires from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S9-5 (SVC3) - S9-3 (SGD3) Always 1 MΩ or higher
S9-9 (SIG3) - S9-3 (SGD3)
S9-5 (SVC3) - S9-9 (SIG3)
S9-5 (SVC3) - Body ground
S9-9 (SIG3) - Body ground
S9-3 (SGD3) - Body ground



Result:
Proceed to
OK
NG



OK

14.CHECK DTC

NG

REPLACE FRONT SEAT WIRE RH

14.CHECK DTC
a.

Connect the connectors to the occupant detection ECU and rear occupant classification sensor LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1782 is not output
DTC B1782 is output


HINT:

DTCs other than DTC B1782 may be output at this time, but they are not related to this check.




DTC B1782 is not output

DTC B1782 is output

15.REPLACE OCCUPANT DETECTION ECU
15.REPLACE OCCUPANT DETECTION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL

Result:
Proceed to
NEXT


HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

16.PERFORM ZERO POINT CALIBRATION
16.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.



Result:
Proceed to
"Zero Point Calibration is complete." is displayed
"Zero Point Calibration is complete." is not displayed



"Zero Point Calibration is complete." is displayed

17.PERFORM SENSITIVITY CHECK

"Zero Point Calibration is complete." is not displayed

19.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH (REAR OCCUPANT CLASSIFICATION SENSOR LH)
17.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
OK
NG



OK

18.CHECK DTC

NG

19.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH (REAR OCCUPANT CLASSIFICATION SENSOR LH)
18.CHECK DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1782 is not output
DTC B1782 is output


HINT:

DTCs other than DTC B1782 may be output at this time, but they are not related to this check.




DTC B1782 is not output

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)

DTC B1782 is output

19.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH (REAR OCCUPANT CLASSIFICATION SENSOR LH)
19.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH (REAR OCCUPANT CLASSIFICATION SENSOR LH)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat adjuster assembly RH.

for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY

for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


HINT:

Perform the inspection using parts from a normal vehicle when possible.


Result:
Proceed to
NEXT



NEXT

20.PERFORM ZERO POINT CALIBRATION
20.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.



Result:
Proceed to
"Zero Point Calibration is complete." is displayed



"Zero Point Calibration is complete." is displayed

21.PERFORM SENSITIVITY CHECK
21.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
NEXT



NEXT

END (FRONT SEAT ADJUSTER ASSEMBLY RH [REAR OCCUPANT CLASSIFICATION SENSOR LH] WAS DEFECTIVE)