Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY › from 2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0189246 CURTAIN SHIELD AIRBAG ASSEMBLY N

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


HINT:
·

Use the same procedure for the LH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

·

If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

B401137



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the curtain shield airbag assembly LH, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.


Hide 62180A 2.DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY LH (When Installed in Vehicle)

NOTICE:
·

When disposing of the curtain shield airbag assembly LH, use an unneeded vehicle to deploy the airbag.

·

Be sure to observe the following procedure when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N26
0.875,1.208 0.833,0.635 0.833,0.635 0.646,0.635 false 0.365,0.563 0.823,0.76 0.458,0.198 10 SST

Check the function of SST.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL

SST
09082-00700  



c.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





e.

Install SST.

i.
B409645C01
0.885,0.583 1.26,0.313 true 1.302,0.208 1.615,0.365 0.313,0.156 10 false *a
*a Connector Lock
V113147

Release in this Direction


Using a screwdriver, pull up the connector lock and disconnect the airbag connector.

NOTICE:

When disconnecting the airbag connector, take care not to damage the airbag wire harness.



ii.
B409650N01
0.521,1.854 0.521,1.531 false 0.417,1.854 1.833,1.854 1.833,1.854 1.833,1.635 false 1.115,1.854 1.115,1.625 false 0.083,1.781 0.542,1.979 0.458,0.198 10 false SST

After connecting the following SST to each other, connect them to the curtain shield airbag assembly LH.

SST
09082-00700  09082-00802  (09082-10801, 09082-20801)

CAUTION:
·
B399562

Do not deploy the curtain shield airbag assembly LH if it rattles due to looseness and the tightening bolts and clips, etc., for the inflator and deployment part of the curtain shield airbag assembly LH falling off.

·

Do not deploy the curtain shield airbag assembly LH if the deployment part fell off.

·

If the curtain shield airbag assembly LH is deployed when it rattles or parts have fallen off, the curtain shield airbag assembly LH may fly off and cause serious injuries.



NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.



iii.
B340835C02
0.729,1.521 0.646,0.917 0.646,0.917 0.521,0.917 false 1.604,1.896 1.917,2.052 0.313,0.156 10 false *a 0.208,0.844 0.667,1.042 0.458,0.198 10 false SST
*a 10 m or more


Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.


iv.

While maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

CAUTION:
B394904

·

Do not deploy with all the doors and door windows open.

·

If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.



NOTICE:

Take care not to damage the SST wire harness.



v.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.



f.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Press the SST activation switch and deploy the airbag.

CAUTION:
B400936

·

Do not deploy with people inside or around the vehicle.

·

If deployed with people inside or around the vehicle, serious injuries may occur.



HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




g.

Remove the curtain shield airbag assembly LH.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CURTAIN SHIELD AIRBAG ASSEMBLY>REMOVAL

CAUTION:
·
B394931

The curtain shield airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B394934

Do not apply water etc. to a curtain shield airbag assembly LH with a deployed airbag.

·

If water is applied to the curtain shield airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

·
B395360

Always wear safety glasses and gloves when handling a deployed curtain shield airbag assembly LH.

·

If the curtain shield airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·

After removal, quickly seal the curtain shield airbag assembly LH in a plastic bag.




h.

Dispose of the curtain shield airbag assembly LH.

i.

Place the curtain shield airbag assembly LH in a plastic bag, tie it tightly and dispose of it according to local regulations.

CAUTION:
·
B399336

The curtain shield airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B399337

Do not apply water etc. to a curtain shield airbag assembly LH with a deployed airbag.

·

If water is applied to the curtain shield airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

·
B399333

Always wear safety glasses and gloves when handling a deployed curtain shield airbag assembly LH.

·

If the curtain shield airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·
B394913

Never dispose of a curtain shield airbag assembly LH with an undeployed airbag.

·

If an undeployed curtain shield airbag assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

·

Always wash your hands with water after completing the operation.





Hide 62180A 3.DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY LH (When not Installed in Vehicle)

NOTICE:

Be sure to observe the following procedure when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N26
0.875,1.208 0.833,0.635 0.833,0.635 0.646,0.635 false 0.365,0.563 0.823,0.76 0.458,0.198 10 SST

Check the function of SST.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL

SST
09082-00700  


b.

Remove the curtain shield airbag assembly LH.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CURTAIN SHIELD AIRBAG ASSEMBLY>REMOVAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B409651

Cut off the deployment section of the curtain shield airbag assembly LH.

CAUTION:
B399333

·

Wear safety glasses and gloves.

·

The dust may enter the eyes or be breathed in.




d.
B104882C28
1.99,1.594 1.99,1.25 false 2.656,0.51 2.969,0.667 0.313,0.156 10 *a 1.917,1.625 2.229,1.781 0.313,0.156 10 *b
*a Wire Diameter
*b Stripped Wire


Using braided wire, tie down the lower curtain shield airbag assembly LH to an unneeded tire.

Wire:
Cross-sectional area of stripped wire:

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire harness is too thin or an alternative object is used to tie down the lower curtain shield airbag assembly LH, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the cross-sectional area of stripped wire:

Area = 3.14 x (Diameter)2 / 4


i.
B409652C01
1.167,1.875 1.479,2.031 0.313,0.156 10 false *a 2.604,1.313 2.917,1.469 0.313,0.156 10 false *b 0.344,0.729 0.656,0.885 0.313,0.156 10 false *c
*a Width
*b Inner Diameter
*c Outlet


Position the curtain shield airbag assembly LH inside the tire as shown in the illustration.

Minimum tire size:

Must exceed the following dimensions

Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


CAUTION:
B399334C01
0.698,1.885 1.354,1.885 true 1.875,2.677 0.979,2.844 true 0.792,2.771 1.104,2.927 0.313,0.156 10 false *a 0.521,1.802 0.833,1.958 0.313,0.156 10 false *b
*a Outlet
*b Remove looseness


·

Do not install the curtain shield airbag assembly LH with the outlet facing down.

·

When securing the curtain shield airbag assembly LH, make sure there is no looseness in the wire harness.

·

If installed with the outlet facing down or looseness in the wire harness, the deployed curtain shield airbag assembly LH and tire may fly off and cause serious injuries.



NOTICE:

The tires may be damaged by the airbag deployment, so use unneeded tires.




e.

Install SST.

i.
B409653N01
2.375,1.344 2.573,0.354 2.573,0.354 2.927,0.354 false 2.896,1.271 2.573,0.354 false 3.01,0.25 3.344,0.479 0.333,0.229 10 false SST

After connecting the following SST to each other, connect them to the curtain shield airbag assembly LH.

SST
09082-00802  (09082-10801, 09082-20801)



f.

Place the tires.

i.
B409654C01
0.583,0.781 1.271,0.781 true 0.885,0.802 0.885,1.427 0.885,1.427 1.271,1.427 true 0.885,1.177 1.292,1.177 true 0.375,0.677 0.688,0.875 0.313,0.198 10 false *a
*a Tires (2 or more)


Place at least 2 tires under the tire to which the curtain shield airbag assembly LH is tied.


ii.

Place at least 2 tires onto the tire to which the curtain shield airbag assembly LH is tied. The top tire should have a wheel installed.

NOTICE:
·

Do not place the SST connector under the tire because it could be damaged.

·

The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.




iii.
B105087

Tie the tires together with the 2 wires.



g.

Install SST.

i.
B404115C01
1.313,2.719 1.625,2.875 0.313,0.156 10 false *a
*a 10 m or more


Connect the SST connector.

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.



ii.

Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.



h.

Deploy the airbag.

i.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the curtain shield airbag assembly LH is tied.


iii.

Press the SST activation switch and deploy the airbag.

CAUTION:
B401767

·

Do not deploy with people around the tire.

·

If deployed with people around the tire, serious injuries may occur.



HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




i.

Dispose of the curtain shield airbag assembly LH.

CAUTION:
·
B399336

The curtain shield airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B399337

Do not apply water etc. to a curtain shield airbag assembly LH with a deployed airbag.

·

If water is applied to the curtain shield airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

·
B399333

Always wear safety glasses and gloves when handling a deployed curtain shield airbag assembly LH.

·

If the curtain shield airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·
B394913

Never dispose of a curtain shield airbag assembly LH with an undeployed airbag.

·

If an undeployed curtain shield airbag assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

·

Always wash your hands with water after completing the operation.



i.

Remove the curtain shield airbag assembly LH from the tire.


ii.

Place the curtain shield airbag assembly LH in a plastic bag, tie it tightly, and dispose of it according to local regulations.