Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the roof headlining removal/installation are shown below.
w/ Airbag System:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>PRECAUTION
1. PRECAUTION (w/ Airbag System)
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
3.REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>REMOVAL
for Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Bench Seat Type)>REMOVAL
4.REMOVE FRONT SEAT ASSEMBLY RH
5.REMOVE REAR SEAT ASSEMBLY
for Seat Cushion 60/40 Split Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Seat Cushion 60/40 Split Type)>REMOVAL
for Seat Cushion Bench Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Seat Cushion Bench Type)>REMOVAL
58810J
6.REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)
58901A
7.REMOVE REAR CONSOLE BOX SUB-ASSEMBLY (w/ Rear Console Box)
58811A
8.REMOVE FRONT CONSOLE BOX (w/o Console Box Lid)
74610A
9.REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
62212
10.REMOVE FRONT PILLAR GARNISH LH
62211
11.REMOVE FRONT PILLAR GARNISH RH
67914B
12.REMOVE FRONT DOOR SCUFF PLATE LH
| *a | Protective Tape |
Put protective tape around the front door scuff plate LH.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the front door scuff plate LH.
67913B
13.REMOVE FRONT DOOR SCUFF PLATE RH
| *a | Protective Tape |
Put protective tape around the front door scuff plate RH.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the front door scuff plate RH.
67918E
14.REMOVE REAR DOOR SCUFF PLATE LH
| *a | Protective Tape |
Put protective tape around the rear door scuff plate LH.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the rear door scuff plate LH.
67917C
15.REMOVE REAR DOOR SCUFF PLATE RH
| *a | Protective Tape |
Put protective tape around the rear door scuff plate RH.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the rear door scuff plate RH.
62414A
16.REMOVE LOWER CENTER PILLAR GARNISH LH
Remove the bolt and disconnect the front seat outer belt assembly LH.
| *1 | Front Door Opening Trim Weatherstrip LH |
| *2 | Rear Door Opening Trim Weatherstrip LH |
Disconnect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the lower center pillar garnish LH.
62413A
17.REMOVE LOWER CENTER PILLAR GARNISH RH
Remove the bolt and disconnect the front seat outer belt assembly RH.
| *1 | Front Door Opening Trim Weatherstrip RH |
| *2 | Rear Door Opening Trim Weatherstrip RH |
Disconnect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the lower center pillar garnish RH.
74617F
18.REMOVE ASSIST GRIP PLUG LH
Use the same procedure for both assist grip plugs.
| *a | Protective Tape |
Put protective tape around the assist grip plug LH.
| *a | Protective Tape |
|
Insert Thin-bladed Screwdriver Here |
|
Remove in this Direction |
Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the assist grip plug LH.
Tape the thin-bladed screwdriver tip before use.
74617A
19.REMOVE ASSIST GRIP PLUG RH
Use the same procedure for both assist grip plugs.
| *a | Protective Tape |
Put protective tape around the assist grip plug RH.
| *a | Protective Tape |
|
Insert Thin-bladed Screwdriver Here |
|
Remove in this Direction |
Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the assist grip plug RH.
Tape the thin-bladed screwdriver tip before use.
74680
20.REMOVE PILLAR ASSIST GRIP ASSEMBLY
Use the same procedure for both pillar assist grip assemblies.
Remove the 2 bolts and pillar assist grip assembly.
73178A
21.REMOVE SEAT BELT ANCHOR COVER CAP
Use the same procedure for both seat belt anchor cover caps.
| *a | Protective Tape |
Put protective tape around the seat belt anchor cover cap.
| *a | Protective Tape |
|
Insert Thin-bladed Screwdriver Here |
|
Remove in this Direction |
Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the seat belt anchor cover cap.
Tape the thin-bladed screwdriver tip before use.
62412B
22.REMOVE UPPER CENTER PILLAR GARNISH LH
Remove the bolt and disconnect the front seat outer belt assembly LH.
| *1 | Front Door Opening Trim Weatherstrip LH |
| *2 | Rear Door Opening Trim Weatherstrip LH |
Disconnect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.
|
Insert Clip Remover Here |
|
Remove in this Direction |
Insert a clip remover at the position shown in the illustration and pull as shown to detach the clip and remove the upper center pillar garnish LH.
62411B
23.REMOVE UPPER CENTER PILLAR GARNISH RH
Remove the bolt and disconnect the front seat outer belt assembly RH.
| *1 | Front Door Opening Trim Weatherstrip RH |
| *2 | Rear Door Opening Trim Weatherstrip RH |
Disconnect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.
|
Insert Clip Remover Here |
|
Remove in this Direction |
Insert a clip remover at the position shown in the illustration and pull as shown to detach the clip and remove the upper center pillar garnish RH.
71397B
24.REMOVE REAR SEATBACK HOLDER
73709
25.REMOVE TETHER ANCHOR BRACKET SUB-ASSEMBLY
Use the same procedure for both tether anchor bracket sub-assemblies.
Remove the bolt and tether anchor bracket sub-assembly.
64261C
26.REMOVE UPPER BACK PANEL GARNISH
| *a | Protective Tape |
Put protective tape around the back panel trim cover.
| *a | Protective Tape |
|
Insert Thin-bladed Screwdriver Here |
|
Remove in this Direction |
Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the back panel trim cover.
Tape the thin-bladed screwdriver tip before use.
| *a | Protective Tape |
Put protective tape around the belt guide.
| *a | Protective Tape |
|
Insert Thin-bladed Screwdriver Here |
|
Remove in this Direction |
Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and disconnect the belt guide.
Tape the thin-bladed screwdriver tip before use.
| *a | Protective Tape |
Put protective tape around the upper back panel garnish.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the upper back panel garnish.
62514A
27.REMOVE LOWER QUARTER TRIM PANEL LH
| *1 | Rear Door Opening Trim Weatherstrip LH |
Disconnect the rear door opening trim weatherstrip LH in the range shown in the illustration.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the lower quarter trim panel LH.
62513A
28.REMOVE LOWER QUARTER TRIM PANEL RH
| *1 | Rear Door Opening Trim Weatherstrip RH |
Disconnect the rear door opening trim weatherstrip RH in the range shown in the illustration.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the lower quarter trim panel RH.
73178B
29.REMOVE SEAT BELT ANCHOR COVER CAP
Use the same procedure for both seat belt anchor cover caps.
| *a | Protective Tape |
Put protective tape around the seat belt anchor cover cap.
| *a | Protective Tape |
|
Insert Thin-bladed Screwdriver Here |
|
Remove in this Direction |
Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the seat belt anchor cover cap.
Tape the thin-bladed screwdriver tip before use.
62512
30.REMOVE QUARTER INSIDE TRIM BOARD LH
Remove the bolt and disconnect the rear seat outer belt assembly LH.
| *1 | Rear Door Opening Trim Weatherstrip LH |
Disconnect the rear door opening trim weatherstrip LH in the range shown in the illustration.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the quarter inside trim board LH.
62511
31.REMOVE QUARTER INSIDE TRIM BOARD RH
Remove the bolt and disconnect the rear seat outer belt assembly RH.
| *1 | Rear Door Opening Trim Weatherstrip RH |
Disconnect the rear door opening trim weatherstrip RH in the range shown in the illustration.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the quarter inside trim board RH.
87810
32.REMOVE INNER REAR VIEW MIRROR ASSEMBLY
81260A
33.REMOVE MAP LIGHT ASSEMBLY
81240
34.REMOVE NO. 1 ROOM LIGHT ASSEMBLY
86466D
35.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)
74325
36.REMOVE VISOR BRACKET COVER LH
Open the visor assembly LH.
| *a | Protective Tape |
|
Insert Thin-bladed Screwdriver Here |
Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the visor bracket cover LH.
Tape the thin-bladed screwdriver tip before use.
74325
37.REMOVE VISOR BRACKET COVER RH
Open the visor assembly RH.
| *a | Protective Tape |
|
Insert Thin-bladed Screwdriver Here |
Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the visor bracket cover RH.
Tape the thin-bladed screwdriver tip before use.
74320
38.REMOVE VISOR ASSEMBLY LH
Remove the 2 screws.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull in the direction (1) shown in the illustration to disconnect the visor assembly LH from the visor holder.
Pull in the direction (2) shown in the illustration to remove the visor assembly LH.
74310
39.REMOVE VISOR ASSEMBLY RH
Remove the 2 screws.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull in the direction (1) shown in the illustration to disconnect the visor assembly RH from the visor holder.
Pull in the direction (2) shown in the illustration to remove the visor assembly RH.
74348
40.REMOVE VISOR HOLDER
Use the same procedure for both visor holders.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Turn the visor holder clockwise approximately 45° and pull it out as shown in the illustration.
Detach the claw and remove the visor holder.
74610A
41.REMOVE ASSIST GRIP SUB-ASSEMBLY
Use the same procedure for all assist grip sub-assemblies.
| *a | Protective Tape |
Put protective tape around the assist grip sub-assembly.
| *a | Protective Tape |
|
Insert Thin-bladed Screwdriver Here |
|
Remove in this Direction |
Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and open the assist grip cover.
Tape the thin-bladed screwdriver tip before use.
Remove the 2 bolts and assist grip sub-assembly.
74605A
42.REMOVE COAT HOOK SUB-ASSEMBLY
Use the same procedure for both coat hook sub-sub-assemblies.
| *a | Protective Tape |
Using a thin-bladed screwdriver, push on the area shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Turn the coat hook sub-assembly clockwise approximately 90° and pull it out as shown in the illustration to remove it.
63339A
43.REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/o Assist Grip)
Using a clip remover, remove the 2 roof headlining service hole covers.
63310
44.REMOVE ROOF HEADLINING ASSEMBLY
w/o Pre-crash Safety System:
Disconnect the connector and detach the clamp from the front pillar LH.
w/ Pre-crash Safety System:
Disconnect the connector and detach the clamp from the front pillar LH.
w/ Pre-crash Safety System:
Disconnect the connector.
Disconnect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip LH | *2 | Rear Door Opening Trim Weatherstrip LH |
Disconnect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip RH | *2 | Rear Door Opening Trim Weatherstrip RH |
Using a clip remover, remove the clip.
|
Remove in this Direction |
Turn the roof headlining assembly diagonally and bend slightly to remove it from the front door.
Make sure wrinkles do not form in the roof headlining assembly during removal.
Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining assembly or vehicle interior.
66423
45.REMOVE FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)
Detach the claw and remove the front side rail spacer LH.
66413B
46.REMOVE FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)
Detach the claw and remove the front side rail spacer RH.
66424
47.REMOVE REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)
Detach the claw and remove the rear side rail spacer LH.
66414A
48.REMOVE REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)
Detach the claw and remove the rear side rail spacer RH.
66425A
49.REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)
Detach the claw and remove the rear No. 2 side rail spacer LH.
66415A
50.REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)
Detach the claw and remove the rear No. 2 side rail spacer RH.