| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0088 | Fuel Rail / System Pressure - Too High | The fuel pressure of the common rail exceeds 240000 kPa (2447 kgf/cm2, 34800 psi) (1 trip detection logic). | ·
Pre-stroke control valve (fuel supply pump assembly) ·
Pressure discharge valve (common rail assembly) ·
Open or short in pre-stroke control valve circuit ·
Fuel pressure sensor (common rail assembly) ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0088 | ·
Common Rail Pressure ·
Target Common Rail Pressure |
For more information on the common rail system, refer to System Description (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>SYSTEM DESCRIPTION).
When DTC P0088 is stored, check the internal fuel pressure of the common rail assembly by entering the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure.
| Engine Speed | Common Rail Pressure |
|---|---|
| Idling | Approximately 25000 to 45000 kPa |
| 3000 rpm (No engine load) | Approximately 60000 to 95000 kPa |
Check "Common Rail Pressure" and "Target Common Rail Pressure" in the freeze frame data.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0088 | After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds |
The ECM stores this DTC if the fuel pressure inside the common rail assembly is higher than 240000 kPa (2447 kgf/cm2, 34800 psi). This DTC indicates that: 1) the pre-stroke control valve may be stuck open, or 2) there may be a short in the pre-stroke control valve circuit.
If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read Current DTCs.
| Result | Proceed to |
|---|---|
| P0088 is output | A |
| P0088 and "P0190, P0192 and/or P0193" are output | B |
When there is an open circuit in the fuel pressure sensor circuit, the fuel pressure sensor outputs the maximum value. Therefore, P0088 may be stored together with DTCs which indicate common rail fuel pressure sensor circuit malfunctions.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Record the stored DTCs and freeze frame data.
| Result | Proceed to |
|---|---|
| Value of Common Rail Pressure is shifting towards 160000 kPa or higher in 3rd and 4th set of freeze frame data | B |
| Except above | A |
A
B
| *a | Component with harness connected
(ECM) |
Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.
Turn the ignition switch to ON.
Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.
| *1 | Engine | *2 | Engine Wire |
| *3 | Common Rail Assembly (Fuel Pressure Sensor) | *4 | Wire to Wire |
| *5 | ECM | - | - |
| *a | Vibration Method (Reference) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C59-18 (PCR1) - Body ground | Vibration is applied to the wire harness and connectors | No noise in the waveform |
| Result | Proceed to |
|---|---|
| MIL comes on or noise present in the waveform | B |
| Except above | A |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Pre-stroke Control Valve
| Tester Display |
|---|
| Activate the Pre-stroke Control Valve |
Perform the Active Test and check that operation sounds can be heard from the pre-stroke control valve.
Perform this procedure with the engine stopped and check the operation sounds from outside the vehicle.
Check in a quiet location with the hood opened, as the operation sound is difficult to hear.
In order to distinguish between the operation sounds of other actuators, check by using the GTS to turn the Active Test open and close several times.
The operation sound is generated when performing the Active Test, and stops when finished.
| Proceed to |
|---|
| OK |
| NG |
NG
OK
Replace the fuel supply pump assembly.
Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SUPPLY PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and start the engine.
After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P0088.
Check the DTC judgment result.
| GTS Display | Result | Proceed to |
|---|---|---|
| Pending DTC | P0088 is output | A |
| All Readiness | NORMAL | B |
| ABNORMAL | A |
If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.
A
B
Replace the ECM.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Component with harness connected
(ECM) |
Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.
Turn the ignition switch to ON.
Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C59-18 (PCR1) - Body ground | Vibration is applied to the wire harness and connectors | No noise in the waveform |
| Result | Proceed to |
|---|---|
| MIL comes on or noise present in the waveform | A |
| Except above | B |
A
B
Replace the common rail assembly.
Click hereEngine / Hybrid System>2GD-FTV FUEL>COMMON RAIL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and start the engine.
After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P0088.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.
| Proceed to |
|---|
| NEXT |
NEXT