Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › from 2016.08
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0278511 ECD SYSTEM(w/o EGR Cooler) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P0191  Fuel Rail Pressure Sensor Circuit Range / Performance  


DESCRIPTION

Refer to DTC P0087.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>P0087

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0191 Fuel Rail Pressure Sensor Circuit Range / Performance The difference between the main and sub voltage outputs of the fuel pressure sensor is 0.04 V or less, or 1.06 V or higher for 1 second or more (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0191
·

Common Rail Pressure

·

Target Common Rail Pressure



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0191 Idling for 1 second or more

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure and Target Common Rail Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
Target Common Rail Pressure
Common Rail Pressure
50003 234 850,851

d.

Start the engine.


e.

Check the change in the values for the data list items above when increasing the engine speed from idling to 3000 rpm with no load.

Result:
Result Proceed to
Common Rail Pressure is always 10000 kPa or less
or
Common Rail Pressure is always 220000 kPa or higher
A
Except above B


HINT:

Normally, "Common Rail Pressure" is within 5000 kPa of "Target Common Rail Pressure".




A

2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

B

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z2-5 (PR) - C59-18 (PCR1) Always Below 1 Ω
Z2-2 (PR2) - C60-26 (PCR2) Always Below 1 Ω
Z2-1 (VCS) - C60-33 (VCS) Always Below 1 Ω
Z2-6 (VC) - C59-28 (VCM) Always Below 1 Ω
Z2-4 (E2) - C59-19 (E2M) Always Below 1 Ω
Z2-3 (E2S) - C60-25 (E2S) Always Below 1 Ω
Z2-5 (PR) or C59-18 (PCR1) - Body ground and other terminals Always 10 kΩ or higher
Z2-2 (PR2) or C60-26 (PCR2) - Body ground and other terminals Always 10 kΩ or higher
Z2-1 (VCS) or C60-33 (VCS) - Body ground and other terminals Always 10 kΩ or higher
Z2-6 (VC) or C59-28 (VCM) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the fuel pressure sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE COMMON RAIL ASSEMBLY

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Let the engine idle for 1 second or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
P0191 is output A
No DTC is output B




A

5.REPLACE COMMON RAIL ASSEMBLY

B

END

5.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>2GD-FTV FUEL>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.BLEED AIR FROM FUEL SYSTEM
6.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Let the engine idle for 1 second or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
P0191 is output A
No DTC is output B




A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Let the engine idle for 1 second or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END