The EGR actuator is operated by the ECM and opens and closes the EGR valve using gears. The opening angle of the EGR valve is detected by the EGR position sensor, which is mounted on the electric EGR control valve assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0489 | Exhaust Gas Recirculation Control Circuit Low | Both of the following conditions are met for 2.0 seconds (1 trip detectionlogic):
·
The EGR actuator duty cycle is 80% or higher. ·
EGR actuator current is below 0.5 A. |
·
Open or short in EGR actuator circuit ·
Electric EGR control valve assembly ·
ECM |
Comes on | DTC stored |
| P0490 | Exhaust Gas Recirculation Control Circuit High | An EGR actuator current of 8 A or higher or the ECM internal circuit temperature of 150 to 160°C (302 to 320°F) or higher is detected.
(1 trip detection logic): |
·
Open or short in EGR actuator assembly circuit ·
Electric EGR control valve assembly ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0489 | ·
Actual EGR Valve Pos ·
Target EGR Valve Pos |
| P0490 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0489 | Idle the engine for 5 seconds or more |
| P0490 |
Refer to DTC P042E.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>P042E
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Remove the electric EGR control valve assembly.
Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>EGR VALVE>REMOVAL
| *a | Component without harness connectoted
(Electric EGR Control Valve Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (M-) - 4 (M+) | Always | No short or open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the electric EGR control valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C95-4 (M+) - C59-6 (EGM+) | Always | Below 1 Ω |
| C95-5 (M-) - C59-7 (EGM-) | Always | Below 1 Ω |
| C95-4 (M+) or C59-6 (EGM+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C95-5 (M-) or C59-7 (EGM-) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the electric EGR control valve assembly connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine.
Idle the engine for 5 seconds or more
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the electric EGR control valve assembly.
Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>EGR VALVE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT