Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › from 2016.08
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0278511 ECD SYSTEM(w/o EGR Cooler) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the ECM detects the starter signal (STA signal) and performs engine control when the engine starts.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) or more for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.4 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
·

ST NO. 1 relay circuit

·

Ignition switch assembly

·

Clutch start switch

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0617 Starter Signal

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0617 Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more

WIRING DIAGRAM

w/ Smart Entry and Start System
A359761E09
0.604,0.354 0.917,0.552 0.313,0.198 10 false NE 0.438,0.708 0.917,0.906 0.479,0.198 10 false STAR 0.542,2.521 1.021,2.719 0.479,0.198 10 false STA 6.365,2.531 6.844,2.729 0.479,0.198 10 false STA 6.375,0.708 6.854,0.906 0.479,0.198 10 false NSW 6.375,0.365 6.854,0.563 0.479,0.198 10 false NEO 6.063,0.26 6.542,0.427 0.479,0.167 10 false 23 6.063,0.615 6.542,0.781 0.479,0.167 10 false 11 6.063,2.438 6.542,2.604 0.479,0.167 10 false 22 3.917,1.323 4.396,1.49 0.479,0.167 10 false B2 3.927,1.51 5.292,1.781 1.365,0.271 10 false Clutch Start Switch 0.927,0.354 1.406,0.521 0.479,0.167 10 false G69 0.927,0.708 1.406,0.875 0.479,0.167 10 false G70 0.979,0.531 1.458,0.698 0.479,0.167 10 false 16 1.021,0.167 1.5,0.333 0.479,0.167 10 false 6 0.969,2.344 1.448,2.51 0.479,0.167 10 false 37 0.927,2.521 1.406,2.688 0.479,0.167 10 false G70 0.135,2.927 1.958,3.302 1.823,0.375 10 false Certification ECU (Smart Key ECU Assembly) 3.646,2.135 4.125,2.302 0.479,0.167 10 false 1 3.646,1.01 4.125,1.177 0.479,0.167 10 false 2 6.438,2.865 6.917,3.031 0.479,0.167 10 false G85 6.438,3.042 6.917,3.208 0.479,0.167 10 false ECM 1.385,4.656 2.5,4.865 1.115,0.208 10 false FL MAIN 3.0W 1.896,3.844 3.01,4.052 1.115,0.208 10 false ST NO. 1 3.813,4.125 4.927,4.333 1.115,0.208 10 false ST NO. 1 3.646,4.5 3.854,4.656 0.208,0.156 10 false 2 3.031,3.76 3.24,3.917 0.208,0.156 10 false 5 3.031,4.51 3.24,4.667 0.208,0.156 10 false 3 3.646,3.75 3.885,3.958 0.24,0.208 10 false 1 3,5.208 3.521,5.375 0.521,0.167 10 false C140 2.365,5.531 2.844,5.698 0.479,0.167 10 false D3 3.031,5.021 3.271,5.229 0.24,0.208 10 false 1 2.375,5.354 2.615,5.563 0.24,0.208 10 false 1 2.656,5.542 3.135,5.708 0.479,0.167 10 false B 2.552,6.156 3.75,6.344 1.198,0.188 10 false Starter Assembly 1.49,5.958 2.031,6.177 0.542,0.219 10 false Battery 3.073,5.406 3.552,5.573 0.479,0.167 10 false ST

w/o Smart Entry and Start System
A348893E14
5.208,3.073 5.542,3.25 0.333,0.177 10 false G85 5.938,4.854 6.281,5.031 0.344,0.177 10 false ECM 5.219,0.781 5.552,0.958 0.333,0.177 10 false G85 5.25,0.573 5.448,0.76 0.198,0.188 10 false 11 5.583,0.792 5.948,0.958 0.365,0.167 10 false NSW 5.583,3.094 5.917,3.271 0.333,0.177 10 false STA 5.25,2.885 5.448,3.073 0.198,0.188 10 false 22 3.667,1.854 3.906,2.021 0.24,0.167 10 false B2 3.656,2.031 4.875,2.24 1.219,0.208 10 false Clutch Start Switch 3.385,1.323 3.5,1.49 0.115,0.167 10 false 2 3.385,2.448 3.5,2.615 0.115,0.167 10 false 1 3.396,3.344 3.51,3.51 0.115,0.167 10 false 2 3.396,4.177 3.51,4.344 0.115,0.167 10 false 1 3.563,3.76 4.188,3.927 0.625,0.167 10 false ST NO. 1 2.667,3.344 2.781,3.51 0.115,0.167 10 false 5 2.667,4.135 2.781,4.302 0.115,0.167 10 false 3 2.625,5.01 2.958,5.188 0.333,0.177 10 false C140 1.292,1.344 2.865,1.531 1.573,0.188 10 false Ignition Switch Assembly 1.292,1.198 1.531,1.365 0.24,0.167 10 false G1 2.583,0.906 2.698,1.073 0.115,0.167 10 false 2 1.313,0.896 1.427,1.063 0.115,0.167 10 false 4 2.25,0.667 2.552,0.833 0.302,0.167 10 false ST2 1.49,0.667 1.813,0.833 0.323,0.167 10 false AM2 1.281,2.635 1.906,2.802 0.625,0.167 10 false ST NO. 1 2.125,5.479 2.323,5.646 0.198,0.167 10 false D3 0.469,1.854 1.635,2.188 1.167,0.333 10 false STRG LOCK/AM2 NO. 1 0.438,3.323 1.385,3.49 0.948,0.167 10 false FL MAIN 2.688,5.219 2.927,5.396 0.24,0.177 10 false ST 2.417,5.5 2.552,5.656 0.135,0.156 10 false B 3,5 3.115,5.167 0.115,0.167 10 false 1 2.156,5.271 2.271,5.438 0.115,0.167 10 false 1 3.302,5.427 4.427,5.615 1.125,0.188 10 false Starter Assembly 0.542,5.896 1.031,6.094 0.49,0.198 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

d.

Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more.

Result:
Result Proceed to
Driving at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more OFF A
ON w/ Smart Entry and Start System B
w/o Smart Entry and Start System C




A

B

2.INSPECT CLUTCH START SWITCH

C

5.INSPECT CLUTCH START SWITCH
2.INSPECT CLUTCH START SWITCH
a.

Inspect the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

REPLACE CLUTCH START SWITCH

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).


Result:
Proceed to
NEXT



NEXT

4.CHECK SMART ENTRY AND START SYSTEM (START FUNCTION)
4.CHECK SMART ENTRY AND START SYSTEM (START FUNCTION)

Result:
Proceed to
OK
NG



OK

NG

REPAIR SMART ENTRY AND START SYSTEM

5.INSPECT CLUTCH START SWITCH
a.

Inspect the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

10.REPLACE CLUTCH START SWITCH
6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

9.REPLACE IGNITION SWITCH ASSEMBLY
7.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER DTC OUTPUT RECURS
8.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

9.REPLACE IGNITION SWITCH ASSEMBLY
a.

Replace the ignition switch assembly.

Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER DTC OUTPUT RECURS
10.REPLACE CLUTCH START SWITCH
a.

Replace the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER DTC OUTPUT RECURS