Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2016.08
RM3250E _56 Audio / Visual / Telematics _057181 TELEMATICS _0280391 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B1572  Microphone Error  


DESCRIPTION

This DTC is stored when a microphone signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1572 Microphone Error Current at terminal MCVD exceeds the malfunction threshold for 20 seconds while the ignition switch is ON.
·

Telematics transceiver

·

Map light assembly (telephone microphone assembly)

·

Harness or connector



WIRING DIAGRAM

E355978E05
0.365,2.042 1.771,2.438 1.406,0.396 10 false Telephone Microphone Assembly 1.49,0.479 2.021,0.719 0.531,0.24 10 false MACC 1.521,0.958 2.052,1.198 0.531,0.24 10 false MCO+ 1.563,1.438 2.094,1.677 0.531,0.24 10 false MCO- 3.135,2.208 3.344,2.427 0.208,0.219 10 false * 4.677,2.208 4.885,2.427 0.208,0.219 10 false * 5.688,2.771 7.156,3.01 1.469,0.24 10 false Telematics Transceiver 5.677,2.583 6.208,2.823 0.531,0.24 10 false G130 0.656,0.594 1.188,0.833 0.531,0.24 10 false MACC 0.74,1.073 1.271,1.313 0.531,0.24 10 false MIC+ 0.76,1.531 1.292,1.771 0.531,0.24 10 false MIC- 1.177,0.521 1.365,0.74 0.188,0.219 10 false 5 1.188,0.99 1.375,1.208 0.188,0.219 10 false 3 1.198,1.458 1.385,1.677 0.188,0.219 10 false 2 2.042,0.51 2.26,0.729 0.219,0.219 10 false 15 2.042,0.979 2.26,1.198 0.219,0.219 10 false 14 2.063,1.458 2.281,1.677 0.219,0.219 10 false 13 5.625,0.51 5.844,0.729 0.219,0.219 10 false 33 5.625,0.979 5.844,1.198 0.219,0.219 10 false 34 5.635,1.448 5.854,1.667 0.219,0.219 10 false 35 5.656,1.917 5.875,2.135 0.219,0.219 10 false 32 5.917,0.604 6.448,0.844 0.531,0.24 10 false MCVD 5.917,1.083 6.448,1.323 0.531,0.24 10 false MCI+ 5.917,1.531 6.448,1.771 0.531,0.24 10 false MCI- 5.906,2.021 6.438,2.26 0.531,0.24 10 false SGND 0.302,3.385 1.99,3.583 1.688,0.198 10 false *: Shielded 0.365,3.042 1.781,3.292 1.417,0.25 10 false Map Light Assembly 0.354,2.885 0.885,3.125 0.531,0.24 10 false Q3

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the G130 telematics transceiver connector.


b.

Disconnect the Q3 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G130-33 (MCVD) - Q3-15 (MACC) Always Below 1 Ω
G130-34 (MCI+) - Q3-14 (MCO+) Always Below 1 Ω
G130-35 (MCI-) - Q3-13 (MCO-) Always Below 1 Ω
G130-33 (MCVD) or Q3-15 (MACC) - Body ground Always 10 kΩ or higher
G130-34 (MCI+) or Q3-14 (MCO+) - Body ground Always 10 kΩ or higher
G130-35 (MCI-) or Q3-13 (MCO-) - Body ground Always 10 kΩ or higher
G130-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL


c.
E355987C01
0.448,0.896 0.802,1.167 0.354,0.271 0.448,2.344 0.802,2.615 0.354,0.271 1,1.573 1.115,1.573 1.115,1.573 1.344,1.24 true 1.698,1.771 1.552,1.771 1.552,1.771 1.469,1.24 true 2.01,1.615 1.865,1.615 1.865,1.615 1.615,1.229 true 1.125,3.073 1.24,3.073 1.24,3.073 1.469,2.74 true 1.969,3.25 1.823,3.25 1.823,3.25 1.74,2.719 true 2.542,3.01 2.396,3.01 2.396,3.01 2.219,2.719 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 0.583,1.49 1.198,1.688 0.615,0.198 10 false MACC 1.74,1.698 2.354,1.896 0.615,0.198 10 false MCO+ 2.063,1.521 2.677,1.719 0.615,0.198 10 false MCO- 0.583,2.396 0.74,2.594 0.156,0.198 10 false B 0.583,0.948 0.74,1.146 0.156,0.198 10 false A 2.594,2.938 3.208,3.135 0.615,0.198 10 false MACC 2.021,3.167 2.635,3.365 0.615,0.198 10 false MIC+ 0.781,2.979 1.396,3.177 0.615,0.198 10 false MIC-
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-15 (MACC) - B-5 (MACC) Always Below 1 Ω
A-14 (MCO+) - B-3 (MIC+) Always Below 1 Ω
A-13 (MCO-) - B-2 (MIC-) Always Below 1 Ω
A-15 (MACC) - A-14 (MCO+) Always 10 kΩ or higher
A-15 (MACC) - A-13 (MCO-) Always 10 kΩ or higher
A-14 (MCO+) - A-13 (MCO-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LAMP ASSEMBLY

4.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

5.REPLACE TELEMATICS TRANSCEIVER
5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT