Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2016.08
RM3250E _56 Audio / Visual / Telematics _057181 TELEMATICS _0280391 TELEMATICS SYSTEM J

TELEMATICS  TELEMATICS SYSTEM  Emergency Call Switch Illumination Circuit  


WIRING DIAGRAM

E355988E03
1,2.302 3.75,2.5 2.75,0.198 10 false Map Light Assembly 0.979,2.135 1.292,2.333 0.313,0.198 10 false Q3 1.427,1.74 4.177,1.938 2.75,0.198 10 false Manual (SOS) Switch 3.458,1.083 3.844,1.292 0.385,0.208 10 false GND 5.167,0.771 5.615,0.979 0.448,0.208 10 false SLED 4.906,1.938 6.49,2.208 1.583,0.271 10 false Telematics Transceiver 4.906,1.771 5.323,2 0.417,0.229 10 false G130 4.969,0.677 5.281,0.875 0.313,0.198 10 false 9 3.854,0.688 4.167,0.885 0.313,0.198 10 false 6 3.865,1.073 4.177,1.271 0.313,0.198 10 false 3 3.406,0.688 3.854,0.896 0.448,0.208 10 false SLED

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)
a.
E265420C10
1.229,0.542 1.365,0.542 1.365,0.542 1.51,1.063 true 1.906,1.073 2.094,0.583 2.094,0.583 2.271,0.583 true 0.188,0.208 0.5,0.406 0.313,0.198 10 false *a 2.313,0.5 2.781,0.708 0.469,0.208 10 false GND 0.833,0.458 1.302,0.667 0.469,0.208 10 false SLED
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect 4 dry-cell batteries (1.5 V each) in series.


c.

Connect a positive (+) from the batteries lead to terminal 6 (SLED) and a negative (-) lead to terminal 3 (GND) of the map light assembly (manual (SOS) switch) connector.


d.

Check if the manual (SOS) switch illuminates.

OK:

Manual (SOS) switch illuminates.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) - TELEMATICS TRANSCEIVER AND BODY GROUND)

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

2.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) - TELEMATICS TRANSCEIVER AND BODY GROUND)
a.

Disconnect the G130 telematics transceiver connector.


b.

Disconnect the Q3 map light assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G130-9 (SLED) - Q3-6 (SLED) Always Below 1 Ω
G130-9 (SLED) or Q3-6 (SLED) - Body ground Always 10 kΩ or higher
Q3-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR