Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2016.08
RM3250E _56 Audio / Visual / Telematics _038052 AUDIO / VIDEO _0182296 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the radio and display receiver assembly via this circuit.

The sound signal that has been sent is amplified by the radio and display receiver assembly and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly, telematics transceiver* or speakers.

*: w/ Telematics Transceiver


WIRING DIAGRAM

E317764E03
5.792,3.688 7.063,4.063 1.271,0.375 10 false G37 5.792,3.854 7.021,4.198 1.229,0.344 10 false Radio and Display Receiver Assembly 5.719,0.771 6.99,1.146 1.271,0.375 10 false 25 5.719,1.385 6.99,1.76 1.271,0.375 10 false 26 5.719,1.99 6.99,2.365 1.271,0.375 10 false 28 5.719,2.604 6.99,2.979 1.271,0.375 10 false 27 5.729,3.198 7,3.573 1.271,0.375 10 false 11 6,3.292 6.896,3.531 0.896,0.24 10 false AGND 5.99,2.688 6.885,2.927 0.896,0.24 10 false VA- 5.969,2.073 6.865,2.313 0.896,0.24 10 false VAL+ 5.979,1.448 6.875,1.688 0.896,0.24 10 false VAR+ 5.969,0.844 6.865,1.083 0.896,0.24 10 false ADPG 0.823,0.833 1.719,1.073 0.896,0.24 10 false ADPG 1.344,0.74 2.24,0.979 0.896,0.24 10 false 10 1.344,1.354 2.24,1.594 0.896,0.24 10 false 7 1.333,2 2.229,2.24 0.896,0.24 10 false 8 1.344,2.594 2.24,2.833 0.896,0.24 10 false 9 1.333,3.198 2.229,3.438 0.896,0.24 10 false 12 0.865,1.458 1.76,1.698 0.896,0.24 10 false VAR+ 0.875,2.073 1.771,2.313 0.896,0.24 10 false VAL+ 0.99,2.698 1.885,2.938 0.896,0.24 10 false VA- 0.844,3.292 1.74,3.531 0.896,0.24 10 false AGND 0.24,3.677 1.135,3.917 0.896,0.24 10 false a1 0.229,3.844 1.406,4.354 1.177,0.51 10 false No. 1 Stereo Jack Adapter Assembly 1.719,3.854 3.479,4.385 1.76,0.531 10 false aG1 1.719,4 3.479,4.531 1.76,0.531 10 false Radio Wiring Sub-assembly 3.781,3.198 4.677,3.438 0.896,0.24 10 false 14 3.781,2.583 4.677,2.823 0.896,0.24 10 false 7 3.771,1.969 4.667,2.208 0.896,0.24 10 false 13 3.771,1.354 4.667,1.594 0.896,0.24 10 false 6 3.781,0.74 4.677,0.979 0.896,0.24 10 false 5 2.365,3.458 3.26,3.698 0.896,0.24 10 false * 4.792,3.469 5.688,3.708 0.896,0.24 10 false * 0.25,4.5 1.146,4.74 0.896,0.24 10 false *: Shielded 3.333,0.74 4.229,0.979 0.896,0.24 10 false 5 3.333,1.323 4.229,1.563 0.896,0.24 10 false 6 3.271,1.979 4.167,2.219 0.896,0.24 10 false 13 3.323,2.594 4.219,2.833 0.896,0.24 10 false 7 3.26,3.188 4.177,3.438 0.917,0.25 10 false 14

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - RADIO WIRING SUB-ASSEMBLY)
a.

Disconnect the G37 radio and display receiver assembly connector.


b.

Disconnect the aG1 radio wiring sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-25 (ADPG) - aG1-5 Always Below 1 Ω
G37-11 (AGND) - aG1-14 Always Below 1 Ω
G37-26 (VAR+) - aG1-6 Always Below 1 Ω
G37-28 (VAL+) - aG1-13 Always Below 1 Ω
G37-27 (VA-) - aG1-7 Always Below 1 Ω
G37-25 (ADPG) or aG1-5 - Body ground Always 10 kΩ or higher
G37-11 (AGND) or aG1-14 - Body ground Always 10 kΩ or higher
G37-26 (VAR+) or aG1-6 - Body ground Always 10 kΩ or higher
G37-28 (VAL+) or aG1-13 - Body ground Always 10 kΩ or higher
G37-27 (VA-) or aG1-7 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK RADIO WIRING SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO WIRING SUB-ASSEMBLY
a.
E317787C01
1.448,2.531 1.906,2.781 0.458,0.25 1.49,0.24 1.948,0.49 0.458,0.25 0.792,1.427 0.99,1.427 0.99,1.427 1.49,1.667 true 0.927,1.146 1.125,1.146 1.125,1.146 1.708,1.635 true 2.021,1.635 2.313,1.385 2.313,1.385 2.521,1.385 true 1.875,1.635 2.365,1.031 2.365,1.031 2.573,1.031 true 2.042,1.948 2.375,2.219 2.375,2.219 2.583,2.219 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.135,2.677 0.448,2.833 0.313,0.156 10 false *b 1.542,2.552 1.938,2.74 0.396,0.188 10 false aG1 1.635,0.271 2.031,0.458 0.396,0.188 10 false a1 2.573,1.292 3.083,1.5 0.51,0.208 10 false ADPG 2.635,0.927 3.146,1.135 0.51,0.208 10 false VA- 0.396,1.313 0.906,1.521 0.51,0.208 10 false VAR+ 0.49,1.031 1,1.24 0.51,0.208 10 false VAL+ 2.646,2.094 3.156,2.302 0.51,0.208 10 false AGND
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)
*b Front view of wire harness connector
(to Vehicle Wire Harness)


Disconnect the No. 1 stereo jack adapter assembly connector.


b.

Disconnect the vehicle wire harness connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a1-10 (ADPG) - aG1-5 Always Below 1 Ω
a1-7 (VAR+) - aG1-6 Always Below 1 Ω
a1-8 (VAL+) - aG1-13 Always Below 1 Ω
a1-9 (VA-) - aG1-7 Always Below 1 Ω
a1-12 (AGND) - aG1-14 Always Below 1 Ω
a1-10 (ADPG) or aG1-5 - Body ground Always 10 kΩ or higher
a1-7 (VAR+) or aG1-6 - Body ground Always 10 kΩ or higher
a1-8 (VAL+) or aG1-13 - Body ground Always 10 kΩ or higher
a1-9 (VA-) or aG1-7 - Body ground Always 10 kΩ or higher
a1-12 (AGND) or aG1-14 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG