Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) › from 2016.08
RM3250E _57 Power Source / Network _038063 NETWORKING _0262515 CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)  DCM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
DCM Communication Stop Mode Either condition is met:
·

"DCM" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "DCM Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of telematics transceiver

·

Telematics transceiver ground circuit

·

Telematics transceiver CAN branch wire or connector

·

Telematics transceiver



WIRING DIAGRAM

C348140E01
5.656,0.99 6.271,1.188 0.615,0.198 10 false CANP 5.656,1.51 6.271,1.708 0.615,0.198 10 false CANN 5.333,0.875 5.948,1.073 0.615,0.198 10 false 15 5.323,1.396 5.938,1.594 0.615,0.198 10 false 16 1.542,0.854 2.156,1.052 0.615,0.198 10 false 9 1.542,1.375 2.156,1.573 0.615,0.198 10 false 19 0.125,1.948 2.417,2.219 2.292,0.271 10 false No. 2 CAN Junction Connector 0.125,1.792 2.417,2.063 2.292,0.271 10 false G68 5.344,5.958 6.896,6.198 1.552,0.24 10 false G130 5.344,6.135 6.896,6.375 1.552,0.24 10 false Telematics Transceiver 5.667,5.396 6.281,5.594 0.615,0.198 10 false E 5.427,5.25 6.042,5.448 0.615,0.198 10 false 4 5.677,2.375 6.292,2.573 0.615,0.198 10 false +B 5.667,4.417 6.281,4.615 0.615,0.198 10 false ACC 5.677,3.688 6.292,3.885 0.615,0.198 10 false IG2 5.438,2.229 6.052,2.427 0.615,0.198 10 false 1 5.438,4.281 6.052,4.479 0.615,0.198 10 false 8 5.438,3.542 6.052,3.74 0.615,0.198 10 false 7 1.021,2.906 3.125,3.104 2.104,0.198 10 false from Engine Stop and Start ECU 1.073,4.958 3.125,5.177 2.052,0.219 10 false from Engine Stop and Start ECU 4.063,2.188 4.792,2.385 0.729,0.198 10 false MAYDAY 4.198,4.219 4.927,4.417 0.729,0.198 10 false ACC 4.052,3.479 4.792,3.677 0.74,0.198 10 false IG2 NO.3 2.219,2.365 3.094,2.604 0.875,0.24 10 false from Battery 2.063,4.427 3.115,4.646 1.052,0.219 10 false from ACC Relay 0.854,3.708 3.094,3.906 2.24,0.198 10 false from IG2 Relay*1, Ignition Switch*2 3.385,2.5 3.76,2.708 0.375,0.208 10 false *3 3.406,3.052 3.781,3.26 0.375,0.208 10 false *4 3.417,4.552 3.792,4.76 0.375,0.208 10 false *3 3.417,5.083 3.792,5.292 0.375,0.208 10 false *4 0.052,5.458 2.156,5.656 2.104,0.198 10 false *1: w/ Entry and Start System 0.031,5.823 2.135,6.021 2.104,0.198 10 false *2: w/o Entry and Start System 0.063,6.135 2.167,6.333 2.104,0.198 10 false *3: w/o Stop and Start System 0.083,6.469 2.188,6.667 2.104,0.198 10 false *4: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least approximately 15 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (TELEMATICS TRANSCEIVER CAN BRANCH WIRE)
a.
C300829C67
0.167,1 0.583,1.25 0.417,0.25 1.813,1.125 1.583,0.417 1.583,0.417 1.417,0.417 true 1.917,1.115 2.167,0.417 2.167,0.417 2.333,0.417 true 0.094,0.094 0.417,0.354 0.323,0.26 10 false *a 0.208,1.052 0.583,1.229 0.375,0.177 10 false G130 1.01,0.354 1.51,0.583 0.5,0.229 10 false CANP 2.396,0.354 2.906,0.583 0.51,0.229 10 false CANN
*a Front view of wire harness connector
(to Telematics Transceiver)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G130-15 (CANP) - G130-16 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)

C

REPAIR OR REPLACE TELEMATICS TRANSCEIVER CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)
a.
C300829C68
1.49,0.25 1.906,0.5 0.417,0.25 0.927,0.938 0.698,0.5 0.698,0.5 0.521,0.5 true 0.927,1.188 0.667,1.917 0.667,1.917 0.5,1.917 true 1.063,1.188 1.24,1.917 1.24,1.917 1.406,1.917 true 2.26,0.917 2.563,0.5 2.563,0.5 2.75,0.5 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.531,0.313 1.938,0.51 0.406,0.198 10 false G130 0.323,0.448 0.688,0.688 0.365,0.24 10 false +B 0.26,1.854 0.635,2.083 0.375,0.229 10 false IG2 1.469,1.844 1.906,2.083 0.438,0.24 10 false ACC 2.792,0.448 3.104,0.708 0.313,0.26 10 false E
*a Front view of wire harness connector
(to Telematics Transceiver)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G130-1 (+B) - Body ground Always 11 to 14 V
G130-7 (IG2) - Body ground Ignition switch ON 11 to 14 V
G130-8 (ACC) - Body ground Ignition switch ACC 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G130-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)
a.
C300829C68
1.49,0.25 1.906,0.5 0.417,0.25 0.927,0.938 0.698,0.5 0.698,0.5 0.521,0.5 true 0.927,1.188 0.667,1.917 0.667,1.917 0.5,1.917 true 1.063,1.188 1.24,1.917 1.24,1.917 1.406,1.917 true 2.26,0.917 2.563,0.5 2.563,0.5 2.75,0.5 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.531,0.313 1.938,0.51 0.406,0.198 10 false G130 0.323,0.448 0.688,0.688 0.365,0.24 10 false +B 0.26,1.854 0.635,2.083 0.375,0.229 10 false IG2 1.469,1.844 1.906,2.083 0.438,0.24 10 false ACC 2.792,0.448 3.104,0.708 0.313,0.26 10 false E
*a Front view of wire harness connector
(to Telematics Transceiver)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G130-1 (+B) - Body ground Always 10.5 to 16 V
G130-7 (IG2) - Body ground Ignition switch ON 11 to 14 V
G130-8 (ACC) - Body ground Ignition switch ACC 10.5 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G130-4 (E) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (+B, ACC terminals) B
NG (IG2, E terminals) C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR