Home › General › INTRODUCTION › REPAIR INSTRUCTION › from 2016.08
RM3250E _V1 General _037969 INTRODUCTION _0187603 REPAIR INSTRUCTION D

INTRODUCTION  REPAIR INSTRUCTION  INITIALIZATION  


PROCEDURES NECESSARY WHEN CABLE IS DISCONNECTED/RECONNECTED TO BATTERY TERMINAL


Necessary Procedures Effect/Inoperative Function when Necessary Procedures not Performed Link
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED


Replacement Part Necessary Procedure Effect or Inoperative Function when Necessary Procedure is not Performed Link
ECM
for 1GR-FE:

VIN registration or frame number registration


DTC P0630 is output (Click here)
for 1KD-FTV, 2KD-FTV:
·

Learning Values Save

·

Learning Values Write

·

VIN registration


Engine starting for 1KD-FTV:(Click here)
for 2KD-FTV:(Click here)
for 1TR-FE, 2TR-FE:

VIN registration or frame number registration


DTC P0630 is output for 1TR-FE:(Click here)
for 2TR-FE:(Click here)
for 1GD-FTV, 2GD-FTV:
·

Learning Values Save

·

Learning Values Write

·

VIN registration


·

Engine starting

·

DTC P0630 is output


for 1GD-FTV:(Click here)
for 1GD-FTV, w/ DPF:(Click here)
for 2GD-FTV:(Click here)
for 2GD-FTV, w/ DPF:(Click here)
for 2GD-FTV, w/ Urea SCR System:(Click here)
for 2GD-FTV, w/o EGR Cooler:(Click here)
for 5L-E:

VIN registration or frame number registration


·

Engine starting

·

DTC P0630 is output


(Click here)

Performing iMT installation information reset


·

iMT system

·

DTCs are output


for RC60, RC61:(Click here)
for RC60F, RC61F:(Click here)
Code registration (Immobiliser system) Engine start function See the Service Bulletin for the registration method.
Engine assembly
for 1GR-FE:

Inspection after repair


Poor idle, engine start, etc. (Click here)
for 1KD-FTV, 2KD-FTV:
·

Input Injector Compensation Code

·

Pilot Quantity Learning


Engine starting for 1KD-FTV:(Click here)
for 2KD-FTV:(Click here)
for 1GD-FTV, 2GD-FTV:
·

Input Injector Compensation Code

·

Pilot Quantity Learning


Engine starting for 1GD-FTV:(Click here)
for 1GD-FTV, w/ DPF:(Click here)
for 2GD-FTV:(Click here)
for 2GD-FTV, w/ DPF:(Click here)
for 2GD-FTV, w/ Urea SCR System:(Click here)
for 2GD-FTV, w/o EGR Cooler:(Click here)
for 1GD-FTV, 2GD-FTV:

Clear Crank Time Compensation Data


Engine starting for 1GD-FTV:(Click here)
for 1GD-FTV, w/ DPF:(Click here)
for 2GD-FTV:(Click here)
for 2GD-FTV, w/ DPF:(Click here)
for 2GD-FTV, w/ Urea SCR System:(Click here)
for 2GD-FTV, w/o EGR Cooler:(Click here)
for 1TR-FE, 2TR-FE:

Inspection after repair


Poor idle, engine start, etc. for 1TR-FE:(Click here)
for 2TR-FE:(Click here)
for 1GD-FTV, 2GD-FTV:

Crankshaft position sensor plate


Clear Crank Time Compensation Data Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data for 1GD-FTV:(Click here)
for 2GD-FTV:(Click here)
for 2GD-FTV, w/o EGR Cooler:(Click here)
for 1GD-FTV (w/ DPF), 2GD-FTV (w/ DPF), 2GD-FTV (w/ Urea SCR System):

Crankshaft angle sensor plate


Clear Crank Time Compensation Data Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data for 1GD-FTV, w/ DPF:(Click here)
for 2GD-FTV, w/ DPF:(Click here)
for 2GD-FTV, w/ Urea SCR System:(Click here)
for 1GD-FTV (w/ DPF), 2GD-FTV (w/ DPF), 2GD-FTV (w/ Urea SCR System):

Air fuel ratio sensor


Clear A/F Sensor Compensation data - for 1GD-FTV, w/ DPF:(Click here)
for 2GD-FTV, w/ DPF:(Click here)
for 2GD-FTV, w/ Urea SCR System:(Click here)
for 1GD-FTV (w/ DPF), 2GD-FTV (w/ DPF), 2GD-FTV (w/ Urea SCR System):

Exhaust manifold converter sub-assembly


Clear DPF Thermal Deterioration Data - for 1GD-FTV, w/ DPF:(Click here)
for 2GD-FTV, w/ DPF:(Click here)
for 2GD-FTV, w/ Urea SCR System:(Click here)
for 1GD-FTV, 2GD-FTV:
·

Diesel throttle body assembly

·

Electric EGR control valve assembly

·

Turbocharger sub-assembly

·

Turbocharger nozzle vane control actuator


Perform initialization - for 1GD-FTV:(Click here)
for 1GD-FTV, w/ DPF:(Click here)
for 2GD-FTV:(Click here)
for 2GD-FTV, w/ DPF:(Click here)
for 2GD-FTV, w/ Urea SCR System:(Click here)
for 2GD-FTV, w/o EGR Cooler:(Click here)
Injector assembly
for 1KD-FTV, 2KD-FTV:
·

Input Injector Compensation Code

·

Pilot quantity learning


Engine starting for 1KD-FTV:(Click here)
for 2KD-FTV:(Click here)
for 1GD-FTV, 2GD-FTV:
·

Input Injector Compensation Code

·

Pilot Quantity Learning


Engine starting for 1GD-FTV:(Click here)
for 1GD-FTV, w/ DPF:(Click here)
for 2GD-FTV:(Click here)
for 2GD-FTV, w/ DPF:(Click here)
for 2GD-FTV, w/ Urea SCR System:(Click here)
for 2GD-FTV, w/o EGR Cooler:(Click here)
for 1KD-FTV, 2KD-FTV:

Fuel supply pump assembly


Supply Pump Initialization Engine startability for 1KD-FTV:(Click here)
for 2KD-FTV:(Click here)
for 1KD-FTV:
·

Diesel throttle body assembly

·

Turbocharger sub-assembly

·

Turbocharger variable nozzle motor


Perform initialization - (Click here)
for 2KD-FTV:

Diesel throttle body assembly


Perform initialization - (Click here)
for 1KD-FTV, 2KD-FTV, 5L-E:

Timing belt


Mode reset operation
·

Does not illuminate when replacement is necessary

·

Illuminates when replacement is not necessary


(Click here)
for 1GR-FE:
·

Throttle with motor body assembly

·

Cleaning the deposits from the throttle with motor body assembly

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair Poor idle, engine start, etc. (Click here)
for 1TR-FE, 2TR-FE:
·

Throttle with motor body assembly

·

Cleaning the deposits from the throttle with motor body assembly

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair Poor idle, engine start, etc. for 1TR-FE:(Click here)
for 2TR-FE:(Click here)
Millimeter wave radar sensor assembly Adjust millimeter wave radar sensor assembly Pre-crash safety system (Click here)
·

Forward recognition camera

·

Windshield glass


Adjust forward recognition camera
·

Forward recognition camera system

·

Lane departure alert system

·

Road sign assist system

·

Pre-crash safety system


(Click here)
Engine stop and start ECU
1.

Upload the number of starter operations

2.

Reset air conditioning information

3.

Learning of air conditioning information

4.

Clear the zero point calibration data

5.

Perform zero point calibration of the deceleration sensor

6.

Check electromagnetic oil pump


Stop and start system (Click here)
w/ Stop and Start System:

Starter assembly


NOTICE:

When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.


Clear the number of starter operations
w/ Stop and Start System:

Flywheel sub-assembly


Total number of engine starts reset
w/ Stop and Start System:

Vehicle with a non-specified battery


Perform battery type switching
for AC60F, w/ Stop and Start System:

Electromagnetic oil pump


Check electromagnetic oil pump
for A750F:
·

Automatic transmission assembly

·

Transmission valve body assembly

·

Any of the shift solenoid valves


Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
for A750F:

Automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly
for AC60E:
·

Automatic transmission assembly

·

Transmission valve body assembly

·

Any of the shift solenoid valves


Reset memory
·

Large shift shock

·

Engine overruns


for 1GR-FE:(Click here)
for 1GD-FTV:(Click here)
for 2GD-FTV:(Click here)
for 2TR-FE:(Click here)
for AC60E:

Automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly
for AC60F:
·

Automatic transmission assembly

·

Transmission valve body assembly

·

Any of the shift solenoid valves


Reset memory
·

Large shift shock

·

Engine overruns


for 1GR-FE:(Click here)
for 1GD-FTV:(Click here)
for 2GD-FTV:(Click here)
for 2TR-FE:(Click here)
for AC60F:

Automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly
·

Tire pressure warning ECU and receiver

·

Tire pressure warning valve and transmitter


·

Register transmitter ID

·

Initialize tire pressure warning system


·

When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.

·

Tire pressure warning function


for Registration:(Click here)
for Initialization:(Click here)
Skid control ECU (Brake actuator assembly)
w/o VSC:

Perform registration of rear differential lock identification information


·

DTCs are output

·

ABS warning light illumination


(Click here)
w/ VSC:

Yaw rate and acceleration sensor zero point calibration and store system information


·

DTCs are output

·

ABS warning light illumination

·

Slip indicator light illumination

·

VSC disable or malfunctioning


(Click here)
Yaw rate and acceleration sensor (airbag sensor assembly)
·

Clear zero point calibration data and store system information

·

Perform yaw rate and acceleration sensor zero point calibration and store system information


w/ Stop and Start System:

Clear zero point calibration data and store system information


Stop and start system (Click here)
Front wheel alignment adjustment
·

Clear zero point calibration data and store system information.

·

Perform yaw rate and acceleration sensor zero point calibration and store system information.


VSC malfunctioning (Click here)
Telematics transceiver Register vehicle information Emergency call service (Click here)
Mobilephone battery Reset mobilephone battery condition
Air conditioning amplifier assembly
w/ Stop and Start System:
1.

Reset air conditioning information

2.

Learning of air conditioning information


Stop and start system (Click here)
Servo motor initialization DTCs are output (Click here)
·

No. 1 air conditioning radiator damper servo sub-assembly

·

No. 2 air conditioning radiator damper servo sub-assembly

·

No. 1 blower damper servo sub-assembly


Servo motor initialization DTCs are output (Click here)
w/ Entry and Start System:
·

Certification ECU (smart key ECU assembly)

·

Steering lock ECU (steering lock actuator assembly)

·

Electrical key transmitter sub-assembly

·

w/ ID Code Box (Immobiliser Code ECU):

ID code box (immobiliser code ECU)


Code registration
·

Wireless door lock control system

·

Entry and start system

·

Immobiliser system

·

Steering lock system


Refer to the Service Bulletin for the registration procedure.
w/o Entry and Start System:
·

Key

·

Transponder key ECU assembly


Code registration Engine starting Refer to the Service Bulletin for the registration procedure.
w/o Entry and Start System:
·

Door control transmitter assembly

·

Door control receiver


Recognition code registration Wireless door lock control system (Click here)
·

Occupant detection ECU

·

Front passenger seat assembly


·

Zero point calibration

·

Sensitivity check


·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)
·

Power window regulator motor assembly

·

Door window regulator assembly

·

Door glass

·

Door glass run


Initialize power window control system
·

Jam protection function

·

Power window control system

·

Auto up and down function

·

Remote control function

·

Key-off operation function

·

Catch protection function


(Click here)
w/ Automatic Light Control System:

Body ECU


Initialize automatic light control system Automatic light control system (Click here)
·

Headlight leveling ECU assembly

·

Rear height control sensor sub-assembly LH

·

The vehicle height changes due to replacement of suspension components or after performing such operations as removal and reinstallation


Headlight leveling ECU assembly initialization Headlight leveling function (Click here)