Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › from 2016.08
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0278511 ECD SYSTEM(w/o EGR Cooler) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, Data List items Stop Light SW is ON when the brake pedal is depressed.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off.
·

Open or short in stop light switch signal circuit

·

STOP fuse

·

IG2 NO. 3 fuse

·

Stop light switch assembly

·

ECM


- DTC stored

Related Data List
DTC No. Data List
P0504 Stop Light Switch

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0504 Depress and release brake pedal with ignition switch ON

WIRING DIAGRAM

A348548E08
6.24,4.542 6.646,4.729 0.406,0.188 10 false ECM 5.698,2.24 5.896,2.406 0.198,0.167 10 false 12 5.698,3.323 5.896,3.49 0.198,0.167 10 false 13 5.958,2.24 6.302,2.406 0.344,0.167 10 false ST1- 5.958,3.323 6.281,3.49 0.323,0.167 10 false STP 4.51,3.781 4.823,3.958 0.313,0.177 10 false A35 4.5,3.948 5.604,4.292 1.104,0.344 10 false Stop Light Switch Assembly 6.24,4.375 6.552,4.552 0.313,0.177 10 false G86 5.365,2.24 5.5,2.406 0.135,0.167 10 false 3 5.375,3.313 5.51,3.479 0.135,0.167 10 false 1 4.396,2.24 4.531,2.406 0.135,0.167 10 false 4 4.396,3.323 4.531,3.49 0.135,0.167 10 false 2 3.76,2.469 4.396,2.646 0.635,0.177 10 false IG2 NO. 3 3.823,2.208 3.958,2.375 0.135,0.167 10 false 1 4.094,2.208 4.229,2.375 0.135,0.167 10 false 2 2.906,3.563 3.323,3.729 0.417,0.167 10 false STOP 2.917,3.292 3.052,3.458 0.135,0.167 10 false 1 3.188,3.292 3.323,3.458 0.135,0.167 10 false 2 0.698,3.573 1.021,3.729 0.323,0.156 10 false ALT 0.635,3.292 0.771,3.458 0.135,0.167 10 false 1 0.927,3.292 1.063,3.458 0.135,0.167 10 false 2 3.115,2.229 3.281,2.396 0.167,0.167 10 false *1 3.563,1.813 3.75,1.979 0.188,0.167 10 false *2 1.635,2.688 1.865,2.854 0.229,0.167 10 false G1 1.656,2.833 3.229,3.021 1.573,0.188 10 false Ignition Switch Assembly 2.771,2.24 2.906,2.406 0.135,0.167 10 false 3 1.51,2.24 1.646,2.406 0.135,0.167 10 false 4 2.458,2.24 2.729,2.406 0.271,0.167 10 false IG2 1.688,2.24 2,2.396 0.313,0.156 10 false AM2 0.427,4.104 0.99,4.271 0.563,0.167 10 false FL MAIN 0.615,4.875 1.125,5.052 0.51,0.177 10 false Battery 0.469,2.469 1.604,2.792 1.135,0.323 10 false STRG LOCK/AM2 NO. 1 0.792,2.208 0.958,2.375 0.167,0.167 10 false 1 1.052,2.208 1.188,2.375 0.135,0.167 10 false 2 1.25,2.219 1.417,2.385 0.167,0.167 10 false *1 0.667,1.021 0.854,1.188 0.188,0.167 10 false *2 3.292,1.031 3.427,1.198 0.135,0.167 10 false 3 2.51,1.031 2.646,1.198 0.135,0.167 10 false 5 4.292,0.552 4.49,0.719 0.198,0.167 10 false 20 4.552,0.646 4.906,0.813 0.354,0.167 10 false IG1D 4.5,1.021 4.813,1.198 0.313,0.177 10 false G69 4.5,1.167 6.625,1.531 2.125,0.365 10 false Certification ECU (Smart Key ECU Assembly) 3.292,0.552 3.427,0.719 0.135,0.167 10 false 1 2.521,0.552 2.656,0.719 0.135,0.167 10 false 2 2.813,1.448 3.083,1.615 0.271,0.167 10 false IG2 1.24,1.271 1.958,1.438 0.719,0.167 10 false AM2 NO. 2 0.406,1.729 0.781,1.885 0.375,0.156 10 false J/B-B 1.635,1 1.771,1.167 0.135,0.167 10 false 2 1.375,1 1.542,1.167 0.167,0.167 10 false 1 0.198,1.615 0.333,1.781 0.135,0.167 10 false 2 0.188,1.865 0.354,2.031 0.167,0.167 10 false 1 4.656,4.917 7.021,5.104 2.365,0.188 10 false *1: w/o Entry and Start System 4.677,5.271 7,5.458 2.323,0.188 10 false *2: w/ Entry and Start System

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the GTS.

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / Engine / Data List / Stop Light Switch.

5.

Check Stop Light Switch when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed ON
Released OFF

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
A253393C19
0.823,1.031 1.188,1.313 0.365,0.281 0.198,0.104 0.51,0.302 0.313,0.198 10 false *a 0.885,1.094 1.198,1.292 0.313,0.198 10 false A35
*a Front view of wire harness connector
(to Stop Light Switch)


Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-2 - Body ground Always 11 to 14 V
A35-4 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

7.REPLACE STOP LIGHT SWITCH ASSEMBLY
3.CHECK ECM (STP AND ST1- VOLTAGE)
a.
A349324C05
2.802,2.448 3.167,2.708 0.365,0.26 2.26,3.854 3.01,3.156 true 3.052,3.854 3.063,3.156 true 0.26,0.594 0.573,0.792 0.313,0.198 10 false *a 1.646,0.594 1.958,0.792 0.313,0.198 10 false *b 0.198,2.25 0.51,2.448 0.313,0.198 10 false *c 2.854,2.5 3.208,2.708 0.354,0.208 10 false G86 1.979,3.885 2.552,4.083 0.573,0.198 10 false 13 (STP) 2.74,3.885 3.396,4.104 0.656,0.219 10 false 12 (ST1-)
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
G86-12 (ST1-) - Body ground Released 7.5 to 14 V
Depressed 0 to 1.5 V
G86-13 (STP) - Body ground Released 0 to 1.5 V
Depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Depress and release the brake pedal.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

7.REPLACE STOP LIGHT SWITCH ASSEMBLY
a.

Replace the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED