This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2284 | Brake Signal Malfunction | The brake signal sent via direct line and the brake signal sent via CAN communication (1-trip detection logic*) do not match. | ·
SMART fuse ·
STOP fuse ·
SFI system ·
ECD system ·
Certification ECU (smart key ECU assembly) ·
Stop light switch assembly ·
Harness or connector |
Connect the cable to the negative (-) battery terminal, release the brake pedal and wait 20 seconds or more. Then depress the brake pedal for 20 seconds or more. |
*: Only detected while a malfunction is present and the engine switch is on (IG).
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
| With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine does not start (the indicator in the combination meter assembly is not illuminated). However, the engine can be started by turning the engine switch on (ACC) and then pressing and holding it.
·
If there is a malfunction when the direct line is on, the engine can be started by pressing the engine switch with the brake pedal released. ·
If there is a malfunction when the direct line is off, the engine cannot be started by pressing the engine switch with the brake pedal depressed. |
- |
| DTC No. | Data List Item | Active Test Item |
|---|---|---|
| B2284 | Power Source Control
·
Stop Light Switch1 |
- |
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.
Inspect the fuses of circuits related to this system before performing the following procedure.
After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Switch1 | State of brake pedal | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
·
Use this item to determine whether the stop light switch is malfunctioning. ·
The engine cannot be started when this item is OFF. ·
When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time. |
| Tester Display |
|---|
| Stop Light Switch1 |
ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.
| Proceed to |
|---|
| OK (for ECD SYSTEM) |
| OK (for SFI SYSTEM) |
| NG |
OK (for ECD SYSTEM)
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for 2KD-FTV: Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for 1GD-FTV (w/ DPF): Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>HOW TO PROCEED WITH TROUBLESHOOTING
for 2GD-FTV: Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for 2GD-FTV (w/ DPF): Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>HOW TO PROCEED WITH TROUBLESHOOTING
for 2GD-FTV (w/ Urea SCR System): Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>HOW TO PROCEED WITH TROUBLESHOOTING
for 2GD-FTV (w/o EGR Cooler): Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>HOW TO PROCEED WITH TROUBLESHOOTING
OK (for SFI SYSTEM)
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>B2271
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>B2271
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G69 certification ECU (smart key ECU assembly) connector.
Disconnect the A35 stop light switch assembly connector.
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-2 - Body ground | Always | 11 to 14 V |
Connect the A35 stop light switch assembly connector.
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G69-11 (STP1) - Body ground | Brake pedal released | 1 V or less |
| Brake pedal depressed | 9 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG