Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › from 2016.08
RM3250E _58 Vehicle Interior _038065 THEFT DETERRENT / KEYLESS ENTRY _0185023 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2286  Runnable Signal Malfunction  B228A  Engine Speed Signal Circuit  P0335  Crankshaft Position Sensor Circuit Malfunction (NE Signal)  


DESCRIPTION

These DTCs are stored when the engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match.

HINT:
·

DTC B2286 is not stored for vehicles with stop and start system.

·

DTC B228A is stored only for vehicles with stop and start system.

·

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.



DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2286 Runnable Signal Malfunction The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication (1-trip detection logic*) do not match.
·

SMART fuse

·

Certification ECU (smart key ECU assembly)

·

SFI system

·

ECD system

·

Harness or connector


Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and reconnect the cable to the negative (-) battery terminal. Wait 20 seconds or more with the engine switch off, then start the engine and maintain an engine speed of 1000 rpm or more for 20 seconds or more.
B228A Engine Speed Signal Circuit The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication (1-trip detection logic*) do not match.
·

SMART fuse

·

Certification ECU (smart key ECU assembly)

·

ECD system

·

Harness or connector


Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and reconnect the cable to the negative (-) battery terminal. Wait 20 seconds or more with the engine switch off, and then start the engine.
P0335 Crankshaft Position Sensor Circuit Malfunction (NE Signal) The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication (1-trip detection logic*) do not match.
·

SMART fuse

·

Certification ECU (smart key ECU assembly)

·

SFI system

·

ECD system

·

Harness or connector


Allow the engine to idle for 10 seconds or more.

*: Only detected while a malfunction is present and the engine switch is on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

When the signal sent via either the direct line or CAN communication is malfunctioning and indicates no vehicle speed, there is no effect on vehicle behavior. (A malfunction is detected after the engine switch is turned on (IG).)

·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the engine cannot be started. However, the engine can be started after the engine switch has been turned off.


·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates no vehicle speed, there is no effect on vehicle behavior.

·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving:

If the following conditions are met, it is determined that the malfunction is not in CAN communication but in the direct line (NE).

1.

When the engine switch is pressed, the system controls the engine based on the starter OFF permission flag (perfect injection signal judgment) via CAN communication, causing the engine to stop cranking.

2.

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via CAN communication, causing the engine to stop cranking.


If the following conditions are met, it is determined that the malfunction is not in the direct line (NE) but in CAN communication.

1.

When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.

2.

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.


If the following conditions are met, it is determined that there is a malfunction in both CAN communication and the direct line (NE).

1.

When the engine switch is pressed, the engine stops cranking after 6 seconds.

2.

When the engine switch is pressed and held, the engine remains cranking for up to 30 seconds.





Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2286
B228A
P0335
Power Source Control
·

Engine Condition


Starting Control
·

Engine Speed


-

WIRING DIAGRAM

C332677E01
1.99,0.615 2.792,0.844 0.802,0.229 10 false from Battery 3.625,0.771 4.396,0.969 0.771,0.198 10 false SMART 1.302,2.427 1.76,2.625 0.458,0.198 10 false ECM 0.552,3.365 2.271,3.573 1.719,0.208 10 false : CAN Communication Line 5.229,0.615 5.542,0.813 0.313,0.198 10 false +B 5.042,0.521 5.198,0.719 0.156,0.198 10 false 1 5.021,1.292 5.177,1.49 0.156,0.198 10 false 6 5.229,1.302 5.542,1.5 0.313,0.198 10 false NE 4.958,2.427 5.417,2.625 0.458,0.198 10 false G69 4.969,2.583 6.49,2.958 1.521,0.375 10 false Certification ECU (Smart Key ECU Assembly) 5.969,1.958 6.125,2.156 0.156,0.198 10 false E 6.177,1.854 6.49,2.052 0.313,0.198 10 false 10 1.625,1.292 2.083,1.49 0.458,0.198 10 false NEO 1.99,1.417 2.448,1.615 0.458,0.198 10 false G46 2.323,1.417 2.781,1.615 0.458,0.198 10 false G85 2.646,1.417 3.104,1.615 0.458,0.198 10 false G88 2.979,1.417 3.438,1.615 0.458,0.198 10 false G84 2.052,1.229 2.365,1.427 0.313,0.198 10 false 16 2.385,1.229 2.698,1.427 0.313,0.198 10 false 23 2.698,1.229 3.01,1.427 0.313,0.198 10 false 13 3.042,1.229 3.354,1.427 0.313,0.198 10 false 17 2.604,2.667 3.667,2.844 1.063,0.177 10 false *1: for 2TR-FE 2.615,2.938 4.302,3.135 1.688,0.198 10 false *2: for 1GD-FTV, 2GD-FTV 2.615,3.198 3.594,3.385 0.979,0.188 10 false *3: for 1GR-FE 2.615,3.469 4.385,3.677 1.771,0.208 10 false *4: for 1KD-FTV, 2KD-FTV 2.042,1.594 2.354,1.792 0.313,0.198 10 false *1 2.375,1.594 2.688,1.792 0.313,0.198 10 false *2 2.708,1.594 3.021,1.792 0.313,0.198 10 false *3 3.021,1.594 3.333,1.792 0.313,0.198 10 false *4

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.READ VALUE USING GTS (ENGINE CONDITION, ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Condition Engine state Stop or Run Stop: Engine stopped
Run: Engine running
-
Body Electrical > Power Source Control > Data List
Tester Display
Engine Condition
50003 223 15
Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed 0 to 16383 r/min Fluctuates in accordance with engine speed -
Body Electrical > Starting Control > Data List
Tester Display
Engine Speed
50003 221 8
OK:

The Data List item changes in accordance with the engine condition.



Result:
Proceed to
OK (for ECD SYSTEM)
OK (for SFI SYSTEM)
NG



OK (for ECD SYSTEM)

OK (for SFI SYSTEM)

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G46*1, G85*2, G88*3 or G84*4 ECM connector.

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1GR-FE

*4: for 1KD-FTV, 2KD-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE:
Tester Connection Condition Specified Condition
G69-6 (NE) - G46-16 (NEO) Always Below 1 Ω
G69-6 (NE) or G46-16 (NEO) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV:
Tester Connection Condition Specified Condition
G69-6 (NE) - G85-23 (NEO) Always Below 1 Ω
G69-6 (NE) or G85-23 (NEO) - Body ground Always 10 kΩ or higher

for 1GR-FE:
Tester Connection Condition Specified Condition
G69-6 (NE) - G88-13 (NEO) Always Below 1 Ω
G69-6 (NE) or G88-13 (NEO) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV:
Tester Connection Condition Specified Condition
G69-6 (NE) - G84-17 (NEO) Always Below 1 Ω
G69-6 (NE) or G84-17 (NEO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the G69 certification ECU (smart key ECU assembly) connector.


b.

Connect the G46*1, G85*2, G88*3 or G84*4 ECM connector.

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1GR-FE

*4: for 1KD-FTV, 2KD-FTV



c.

Check the engine speed input signal waveform at the terminal of the certification ECU (smart key ECU assembly).

C336314C01
2.063,0.521 2.49,0.75 0.427,0.229 1.667,2.75 1.823,2.75 1.823,2.75 2,1.604 true 0.292,0.156 0.604,0.354 0.313,0.198 10 false *a 2.146,0.552 2.604,0.75 0.458,0.198 10 false G69 1.469,2.688 1.781,2.885 0.313,0.198 10 false NE 4.583,4.24 5.042,4.438 0.458,0.198 10 false GND
*a Component with harness connected (Certification ECU (Smart Key ECU Assembly)) - -


Standard Frequency:
Tester Connection Condition Tool Setting Specified Condition
G69-6 (NE) - Body ground Engine stopped 2 V/DIV., 2 ms./DIV. No pulse generation
Engine running 2 V/DIV., 2 ms./DIV. Pulse generation



Result:
Proceed to
OK
NG (for ECD SYSTEM)
NG (for SFI SYSTEM)



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG (for ECD SYSTEM)

NG (for SFI SYSTEM)