Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB BOLT
RM33J0E _52 Drivetrain _038472 AXLE AND DIFFERENTIAL _0187674 FRONT AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.DISCONNECT FRONT FLEXIBLE HOSE (for 2WD)

a.
C322784

Remove the bolt and disconnect the front flexible hose.


Hide 47750 3.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY LH (for 2WD)

a.
C321893C03
1.313,2.292 0.865,2.01 0.865,2.01 0.677,2.01 false 1.958,2.563 1.667,2.781 1.667,2.781 1.542,2.781 false 0.458,1.927 0.615,2.125 0.156,0.198 10 false *a 1.365,2.698 1.563,2.885 0.198,0.188 10 false *b
*a Hold
*b Turn


Hold the front disc brake cylinder slide pin and remove the 2 bolts and disc brake cylinder assembly LH.

NOTICE:

Use wire or an equivalent tool to keep the front disc brake cylinder assembly LH from hanging down by the front flexible hose.



Hide 47722 4.REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH (for 2WD)

a.
C321871

Remove the 2 bolts and front disc brake cylinder mounting LH.


Hide 47750 5.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY LH (for 4WD and Pre-Runner)

F042731

a.

Remove the bolt and brake tube bracket from the steering knuckle.


b.
C321910

Remove the 2 bolts and front disc brake cylinder assembly LH.

NOTICE:

Use wire or an equivalent tool to keep the front disc brake cylinder assembly LH from hanging down by the front flexible hose.



Hide 43502D 7.REMOVE FRONT AXLE HUB BOLT

C324656C01
2.125,0.823 2.563,0.563 2.563,0.563 2.781,0.563 false 2.375,0.927 2.552,0.583 false 2.865,0.51 3.177,0.667 0.313,0.156 10 false *1 1.302,1.75 1.552,1.979 0.25,0.229 10 true *a 2.698,1.396 3.01,1.552 0.313,0.156 10 false *b
*1 Nut
*a Turn
*b Hold


a.

Temporarily install 2 nuts and 2 washers to the 2 front axle hub bolts as shown in the illustration.


b.

Using SST and a screwdriver, remove the hub bolt.

SST
09650-17011  


Hide 43502D 8.INSTALL FRONT AXLE HUB BOLT

C324657C01
0.656,0.969 0.813,0.823 false 1.042,1.156 1.135,1.063 false 2.667,0.823 3.083,0.438 3.083,0.438 2.948,0.917 false 0.844,0.688 1.156,0.844 0.313,0.156 10 false *1 1.156,0.969 1.469,1.125 0.313,0.156 10 false *2 1.594,1.677 1.854,1.896 0.26,0.219 10 true *a 2.938,1.698 3.188,1.917 0.25,0.219 10 false *b 3.115,0.313 3.365,0.542 0.25,0.229 10 true *2
*1 Plate Washer
*2 Nut
*a Turn
*b Hold


a.

Temporarily install a plate washer and nut to a new hub bolt as shown in the illustration.


b.

Using a screwdriver to hold the front axle, install a new hub bolt by tightening the nut. Then remove the nut and plate washer.


c.

Remove the 2 nuts from the hub bolts.


Hide 47750 10.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH (for 4WD and Pre-Runner)

a.

Install the front disc brake cylinder assembly LH with the 2 bolts.

Torque:
197 N*m (2009 kgf*cm, 145 ft.*lbf)


b.

Install the brake tube bracket to the steering knuckle with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 47722 11.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING LH (for 2WD)

a.

Install the front disc brake cylinder mounting LH with the 2 bolts.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)


Hide 12.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH (for 2WD)

C321869C02
1.333,2.333 0.885,2.125 0.885,2.125 0.646,2.125 false 1.979,2.573 1.76,2.75 1.76,2.75 1.625,2.75 false 0.427,2.042 0.604,2.229 0.177,0.188 10 false *a 1.448,2.667 1.604,2.865 0.156,0.198 10 false *b
*a Hold
*b Turn


a.

Hold the front disc brake cylinder slide pin and install the disc brake cylinder assembly LH to the disc brake cylinder mounting LH with 2 bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 13.CONNECT FRONT FLEXIBLE HOSE (for 2WD)

a.

Connect the front flexible hose with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 14.INSTALL FRONT WHEEL