Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE(for 2WD)
RM33J0E _52 Drivetrain _038472 AXLE AND DIFFERENTIAL _0187677 STEERING KNUCKLE(for 2WD) A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE(for 2WD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43502M 1.INSTALL FRONT INNER AXLE HUB BEARING LH

a.
C324899N01
2.573,0.813 2.354,0.469 2.354,0.469 2.667,0.51 false 2.479,1.521 2.646,1.521 false 2.052,0.354 2.51,0.552 0.458,0.198 10 false SST 2.688,1.448 3.146,1.646 0.458,0.198 10 false SST

Using SST and a press, press a new front inner axle hub bearing LH (outer race) into the steering knuckle LH.

SST
09527-17011  
09950-60020  (09951-00750)
09950-70010  (09951-07100)


Hide 43512E 2.INSTALL FRONT AXLE HUB HOLE SNAP RING LH

a.
C324897

Using a snap ring pliers, install a new front axle hub hole snap ring LH to the steering knuckle LH.


Hide 43502F 3.INSTALL FRONT AXLE HUB OIL SEAL LH

a.

Install a new front inner axle hub bearing LH (outer side inner bearing) to the steering knuckle LH.


b.
C324900N01
0.74,0.854 0.51,0.563 0.51,0.563 0.906,0.646 false 0.635,1.979 0.854,1.667 false 0.177,0.448 0.635,0.646 0.458,0.198 10 false SST 0.313,1.917 0.771,2.115 0.458,0.198 10 true SST

Using SST and a press, press a new front axle hub oil seal LH into the steering knuckle LH.

SST
09527-17011  
09950-60020  (09951-00810)
09950-70010  (09951-07100)


c.

Apply MP grease to the lip of the front axle hub oil seal LH.


d.

Install the dust cover with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 43502C 4.INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH

a.
C325400N01
0.729,0.281 1.448,0.427 false 2.135,1.583 2.75,1.583 false 0.375,0.167 0.833,0.365 0.458,0.198 10 false SST 2.833,1.51 3.292,1.708 0.458,0.198 10 false SST

Using SST and a press, press the front axle hub sub-assembly LH into the steering knuckle LH.

SST
09950-60010  (09951-00600)
09527-17011  


b.
C324901N01
0.406,0.438 0.844,1.125 true 0.5,1.76 0.781,1.708 true 0.167,1.698 0.625,1.896 0.458,0.198 10 false SST 0.094,0.302 0.552,0.5 0.458,0.198 10 false SST

Using SST and a press, press a new front inner axle hub bearing LH (inner side inner race) into the front axle hub sub-assembly LH.

SST
09223-00010  
09527-17011  


c.

Install 3 new front axle hub bolts.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB BOLT>REPLACEMENT


Hide 43515 5.INSTALL FRONT SKID CONTROL ROTOR

a.
C324903

Install the front skid control rotor as shown in the illustration.

NOTICE:

Take care not to scratch the serration of the front skid control rotor.



Hide 43502H 6.INSTALL FRONT AXLE SHAFT NUT LH

a.
C325401

Using a 36 mm socket wrench, install a new front axle shaft nut LH to the front axle hub sub-assembly LH.

Torque:
199 N*m (2029 kgf*cm, 147 ft.*lbf)


b.
C324891N01
1.833,0.667 2.333,0.667 false 2.406,0.594 2.865,0.792 0.458,0.198 10 false SST

Using SST and a hammer, stake the front axle shaft nut LH.

SST
09930-00010  (09931-00010, 09931-00020)

NOTICE:

Do not scratch the serration of the front skid control rotor.



Hide 43442B 7.INSTALL KNUCKLE GREASE RETAINER CAP LH

a.
C332705C01
0.76,0.844 0.458,0.594 0.458,0.594 0.927,0.625 true 0.406,1.073 0.74,1.073 true 1.646,2 1.885,2 1.885,2 2.333,1.667 true 0.146,0.521 0.604,0.719 0.458,0.198 10 false SST 0.073,1 0.531,1.198 0.458,0.198 10 false SST 1.281,1.896 1.74,2.094 0.458,0.198 10 true SST 3.135,1.229 3.375,1.427 0.24,0.198 10 false *a
*a Clearance


Using SST and a hammer, tap the knuckle grease retainer cap LH.

SST
09527-17011  
09950-60020  (09951-00910)
09950-70010  (09951-07150)

Standard clearance:

0.2 mm (0.0079 in.) or less


NOTICE:

Do not damage the knuckle grease retainer cap LH.



Hide 48630 8.CONNECT FRONT UPPER SUSPENSION ARM ASSEMBLY LH

a.

Connect the front upper suspension arm assembly LH to the steering knuckle LH with a new nut.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


b.

Install a new clip.

NOTICE:

If the holes for the clip are not aligned, tighten the nut an additional 60°.



Hide 48069 9.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM ASSEMBLY LH

C322830

a.

Connect the front lower No. 1 suspension arm LH to the steering knuckle LH with the 2 bolts.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)


Hide 45047 10.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 47722 12.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING LH

Hide 47750 13.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH

Hide 14.CONNECT FRONT FLEXIBLE HOSE

Hide 89543 15.CONNECT FRONT SPEED SENSOR LH

a.
C322632

Install the front speed sensor LH with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the front speed sensor LH tip.

·

While inserting the front speed sensor LH into the knuckle hole, do not strike or damage the sensor tip.

·

After installing the front speed sensor LH, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

·

When installing the front speed sensor LH, do not twist the wire harness.




b.

Install the harness clamp to the steering knuckle with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)

NOTICE:
·

When installing the harness clamp, do not twist the wire harness.

·

Make sure the clamp rotation stopper touches the installation position.




c.
C322631

Install the harness clamp to the front lower arm bracket with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)

NOTICE:
·

When installing the harness clamp, do not twist the wire harness.

·

Make sure the harness clamp rotation stopper touches the installation position.




d.

Install the harness clamp to the front absorber bracket with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)

NOTICE:
·

When installing the harness clamp, do not twist the wire harness.

·

Make sure the harness clamp rotation stopper touches the installation position.




Hide 16.INSTALL FRONT WHEEL

Hide 17.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT