Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.06–2015.11
RM33J0E _58 Vehicle Interior _038499 METER / GAUGE / DISPLAY _0189806 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the brake actuator assembly (skid control ECU) which uses this information to create the vehicle speed signal*. The vehicle speed signal consists of pulses sent to the combination meter assembly from the brake actuator assembly (skid control ECU). To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the brake actuator assembly (skid control ECU). The pulse signal is created by switching the transistor in the brake actuator assembly (skid control ECU) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the brake actuator assembly (skid control ECU). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.

*: This vehicle speed signal is created by the brake actuator assembly (skid control ECU). There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

E326575E01
0.552,1.323 2.146,1.698 1.594,0.375 10 false Brake Actuator Assembly (Skid Control ECU) 1.458,0.417 1.927,0.656 0.469,0.24 10 false SP1 5.427,0.417 5.896,0.656 0.469,0.24 10 false SI 5.417,2.656 5.885,2.896 0.469,0.24 10 false +S 5.135,2.646 5.604,2.885 0.469,0.24 10 false 19 5.156,0.406 5.625,0.646 0.469,0.24 10 false 18 1.833,0.323 2.302,0.563 0.469,0.24 10 false 14*1 2.281,0.323 2.75,0.563 0.469,0.24 10 false 22*2 1.896,0.531 2.365,0.771 0.469,0.24 10 false A4 2.344,0.521 2.813,0.76 0.469,0.24 10 false A3 1.01,3.177 1.948,3.542 0.938,0.365 10 false ECM 5.219,3.24 7.156,3.438 1.938,0.198 10 false G9 5.219,3.385 7.156,3.583 1.938,0.198 10 false Combination Meter Assembly 6.479,2.385 6.948,2.625 0.469,0.24 10 false CPU 1.854,2.74 2.323,2.979 0.469,0.24 10 false G45 1.854,2.552 2.323,2.792 0.469,0.24 10 false 23*3 2.271,2.542 2.74,2.781 0.469,0.24 10 false 10*4 2.677,2.542 3.146,2.781 0.469,0.24 10 false 17*5 1.406,2.656 1.875,2.896 0.469,0.24 10 false SPD 1.375,4.344 1.844,4.583 0.469,0.24 10 false SPD 5.521,4.354 5.99,4.594 0.469,0.24 10 false SPD 5.531,6.063 6,6.302 0.469,0.24 10 false SPD1 1.417,6.063 1.885,6.302 0.469,0.24 10 false SPD 5.542,7.75 6.01,7.99 0.469,0.24 10 false SPD 2.271,2.74 2.74,2.979 0.469,0.24 10 false G85 2.708,2.729 3.177,2.969 0.469,0.24 10 false G83 1.844,4.344 2.313,4.583 0.469,0.24 10 false 7 1.833,6.063 2.302,6.302 0.469,0.24 10 false 17 0.438,4.865 2.313,5.177 1.875,0.313 10 false G69 0.438,5.021 3.427,5.229 2.99,0.208 10 false Certification ECU (Smart Key ECU Assembly)*6 5.354,4.344 5.823,4.583 0.469,0.24 10 false 5 5.708,4.885 6.646,5.25 0.938,0.365 10 false G27 5.708,5.031 6.646,5.396 0.938,0.365 10 false Body ECU*7 0.292,6.469 2.875,6.667 2.583,0.198 10 false G37 0.302,6.625 2.885,6.823 2.583,0.198 10 false Radio and Display Receiver Assembly*9 5.281,7.74 5.75,7.979 0.469,0.24 10 false 17 5.26,6.052 5.729,6.292 0.469,0.24 10 false 25 5.75,6.573 6.219,6.813 0.469,0.24 10 false G90 5.75,6.729 6.219,6.969 0.469,0.24 10 false TCM*8 5.25,8.281 7.083,8.479 1.833,0.198 10 false G117 5.271,8.427 7.104,8.625 1.833,0.198 10 false Radio Receiver Assembly*10 0.094,6.938 2.677,7.135 2.583,0.198 10 false *1: w/ VSC 0.073,7.208 2.656,7.406 2.583,0.198 10 false *2: w/o VSC 0.063,7.49 2.646,7.688 2.583,0.198 10 false *3: for 2TR-FE 0.063,7.771 2.646,7.969 2.583,0.198 10 false *4: for 1GD-FTV, 2GD-FTV 0.052,8.042 2.635,8.24 2.583,0.198 10 false *5: for 1KD-FTV, 2KD-FTV 0.052,8.302 2.635,8.5 2.583,0.198 10 false *6: w/ Smart Entry and Start System 0.073,8.563 3.396,8.75 3.323,0.188 10 false *7: w/ Body ECU 1.031,6.938 3.563,7.146 2.531,0.208 10 false *8: for 1KD-FTV, Automatic Transmission 1.969,7.271 3.521,7.813 1.552,0.542 10 false *9: w/ Audio and Visual System (for Radio and Display Type) 1.281,8.552 4.938,8.75 3.656,0.198 10 false *10: w/ Audio and Visual System (for Radio Receiver Type)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

·

w/ Smart Entry and Start System:

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

If the body ECU has been replaced, it is necessary to initializa the body ECU.



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
NOTICE:

For vehicles without a entry and start system, go to "Check Body ECU".


*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1KD-FTV, 2KD-FTV

*4: for 1KD-FTV, Automatic Transmission

*5: w/ Body ECU

*6: w/ Audio and Visual System (for Radio and Display Type)

*7: w/ Audio and Visual System (for Radio Receiver Type)


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G45*1, G85*2 or G83*3 ECM connector.


c.

Disconnect the G90 TCM connector.*4


d.

Disconnect the G27 body ECU connector.*5


e.

Disconnect the G37 radio and display receiver assembly connector.*6


f.

Disconnect the G117 radio receiver assembly connector.*7


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK BODY ECU

NG

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
2.CHECK BODY ECU
NOTICE:

For vehicles without a body ECU, go to "Check TCM".


*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1KD-FTV, 2KD-FTV

*4: for 1KD-FTV, Automatic Transmission

*5: w/ Smart Entry and Start System

*6: w/ Audio and Visual System (for Radio and Display Type)

*7: w/ Audio and Visual System (for Radio Receiver Type)


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G45*1, G85*2 or G83*3 ECM connector.


c.

Disconnect the G90 TCM connector.*4


d.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


e.

Disconnect the G37 radio and display receiver assembly connector.*6


f.

Disconnect the G117 radio receiver assembly connector.*8


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK TCM

NG

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)
3.CHECK TCM
NOTICE:

For vehicles without a 1KD-FTV series engine, automatic transmission, go to "Check Radio and Display Receiver Assembly".


*1: w/ Smart Entry and Start System

*2: w/ Body ECU

*3: w/ Audio and Visual System (for Radio and Display Type)

*4: w/ Audio and Visual System (for Radio Receiver Type)


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G83 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1


d.

Disconnect the G27 body ECU connector.*2


e.

Disconnect the G37 radio and display receiver assembly connector.*3


f.

Disconnect the G117 radio receiver assembly connector.*4


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
NOTICE:

For vehicles without an audio and visual system (for radio and display type), go to "Check Radio Receiver Assembly".


*1: for 2TR-FE

*2: for 1GD-FTV

*3: for 1KD-FTV

*4: for 1KD-FTV, Automatic Transmission

*5: w/ Smart Entry and Start System

*6: w/ Body ECU


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G45*1, G85*2 or G83*3 ECM connector.


c.

Disconnect the G90 TCM connector.*4


d.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


e.

Disconnect the G27 body ECU connector.*6


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK RADIO RECEIVER ASSEMBLY

NG

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
5.CHECK RADIO RECEIVER ASSEMBLY
NOTICE:

For vehicles without an audio and visual system (for radio receiver type), go to "Check ECM".


*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1KD-FTV, 2KD-FTV

*4: for 1KD-FTV, Automatic Transmission

*5: w/ Smart Entry and Start System

*6: w/ Body ECU


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G45*1, G85*2 or G83*3 ECM connector.


c.

Disconnect the G90 TCM connector.*4


d.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


e.

Disconnect the G27 body ECU connector.*6


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK ECM

NG

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)
6.CHECK ECM

*1: w/ Smart Entry and Start System

*2: w/ Body ECU

*3: w/ Audio and Visual System (for Radio and Display Type)

*4: w/ Audio and Visual System (for Radio Receiver Type)

*5: for 1KD-FTV, Automatic Transmission


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1


c.

Disconnect the G27 body ECU connector.*2


d.

Disconnect the G37 radio and display receiver assembly connector.*3


e.

Disconnect the G117 radio receiver assembly connector.*4


f.

Disconnect the G90 TCM connector.*5


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
7.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.
C317099C04
1.448,2.479 1.896,2.771 0.448,0.292 1.458,0.125 1.906,0.417 0.448,0.292 0.51,1.729 0.688,1.729 0.688,1.729 1.094,1.021 true 2.531,4.406 2.344,4.406 2.344,4.406 1.958,3.594 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 2.604,4.313 3.219,4.51 0.615,0.198 10 false SP1 1.604,0.177 1.917,0.375 0.313,0.198 10 false A4 1.594,2.531 1.906,2.729 0.313,0.198 10 false A3 1.979,0.198 2.292,0.396 0.313,0.198 10 false *A 1.958,2.542 2.271,2.74 0.313,0.198 10 false *B 0.177,1.594 0.792,1.792 0.615,0.198 10 false SP1
*A w/ VSC
*B w/o VSC
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ VSC
Tester Connection Switch Condition Specified Condition
A4-14 (SP1) - Body ground Ignition switch ON 11 to 14 V

w/o VSC
Tester Connection Switch Condition Specified Condition
A3-22 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
8.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
E200403C12
1.521,0.26 1.917,0.479 0.396,0.219 1.052,1.125 0.771,0.865 0.771,0.865 0.615,0.865 true 0.406,0.76 0.708,1.073 0.302,0.313 10 false SI 1.625,0.281 1.99,0.469 0.365,0.188 10 false G9 1.333,4.094 1.458,4.24 0.125,0.146 10 false A 2.969,3.51 3.427,3.885 0.458,0.375 10 false GND 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.094,2.448 0.406,2.604 0.313,0.156 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Connect an oscilloscope to terminal G9-18 (SI) and body ground.


c.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection G9-18 (SI) - Body ground
Tool Setting 5 V/DIV, 20 ms./DIV
Vehicle Condition Driving at approximately 20 km/h (12 mph)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1KD-FTV, 2KD-FTV

*4: for 1KD-FTV, Automatic Transmission

*5: w/ Body ECU

*6: w/ Audio and Visual System (for Radio and Display Type)

*7: w/ Audio and Visual System (for Radio Receiver Type)


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G45*1, G85*2 or G83*3 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G90 TCM connector.*4


e.

Disconnect the G27 body ECU connector.*5


f.

Disconnect the G37 radio and display receiver assembly connector.*6


g.

Disconnect the G117 radio receiver assembly connector.*7


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G69-7 (SPD) Always Below 1 Ω
G9-19 (+S) or G69-7 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1KD-FTV, 2KD-FTV

*4: for 1KD-FTV, Automatic Transmission

*5: w/ Smart Entry and Start System

*6: w/ Audio and Visual System (for Radio and Display Type)

*7: w/ Audio and Visual System (for Radio Receiver Type)


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G27 body ECU connector.


c.

Disconnect the G45*1, G85*2 or G83*3 ECM connector.


d.

Disconnect the G90 TCM connector.*4


e.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


f.

Disconnect the G37 radio and display receiver assembly connector.*6


g.

Disconnect the G117 radio receiver assembly connector.*7


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G27-5 (SPD) Always Below 1 Ω
G9-19 (+S) or G27-5 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)

*1: w/ Smart Entry and Start System

*2: w/ Speed-sensitive Automatic Door Lock Function

*3: w/ Audio and Visual System (for Radio and Display Type)

*4: w/ Audio and Visual System (for Radio Receiver Type)


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G90 TCM connector.


c.

Disconnect the G83 ECM connector.


d.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1


e.

Disconnect the G27 body ECU connector.*2


f.

Disconnect the G37 radio and display receiver assembly connector.*3


g.

Disconnect the G117 radio receiver assembly connector.*4


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G90-25 (SPD1) Always Below 1 Ω
G9-19 (+S) or G90-25 (SPD1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

*1: for 2TR-FE

*2: for 1GD-FTV

*3: for 1KD-FTV

*4: for 1KD-FTV, Automatic Transmission

*5: w/ Smart Entry and Start System

*6: w/ Body ECU


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G37 radio and display receiver assembly connector.


c.

Disconnect the G45*1, G85*2 or G83*3 ECM connector.


d.

Disconnect the G90 TCM connector.*4


e.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


f.

Disconnect the G27 body ECU connector.*6


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G37-17 (SPD) Always Below 1 Ω
G9-19 (+S) or G37-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1KD-FTV, 2KD-FTV

*4: for 1KD-FTV, Automatic Transmission

*5: w/ Smart Entry and Start System

*6: w/ Body ECU


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G117 radio receiver assembly connector.


c.

Disconnect the G45*1, G85*2 or G83*3 ECM connector.


d.

Disconnect the G90 TCM connector.*4


e.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


f.

Disconnect the G27 body ECU connector.*6


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G117-17 (SPD) Always Below 1 Ω
G9-19 (+S) or G117-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1KD-FTV, 2KD-FTV

*4: for 1KD-FTV, Automatic Transmission

*5: w/ Smart Entry and Start System

*6: w/ Body ECU

*7: w/ Audio and Visual System (for Radio and Display Type)

*8: w/ Audio and Visual System (for Radio Receiver Type)


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G45*1, G85*2 or G83*3 ECM connector.


c.

Disconnect the G90 TCM connector.*4


d.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


e.

Disconnect the G27 body ECU connector.*6


f.

Disconnect the G37 radio and display receiver assembly connector.*7


g.

Disconnect the G117 radio receiver assembly connector.*8


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G9-19 (+S) - G45-23 (SPD) Always Below 1 Ω
G9-19 (+S) or G45-23 (SPD) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Specified Condition
G9-19 (+S) - G85-10 (SPD) Always Below 1 Ω
G9-19 (+S) or G85-10 (SPD) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV
Tester Connection Condition Specified Condition
G9-19 (+S) - G83-17 (SPD) Always Below 1 Ω
G9-19 (+S) or G83-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the A4*1 or A3*2 brake actuator assembly (skid control ECU) connector.

*1: w/ VSC

*2: w/o VSC



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ VSC
Tester Connection Condition Specified Condition
G9-18 (SI) - A4-14 (SP1) Always Below 1 Ω
G9-18 (SI) or A4-14 (SP1) - Body ground Always 10 kΩ or higher

w/o VSC
Tester Connection Condition Specified Condition
G9-18 (SI) - A3-22 (SP1) Always Below 1 Ω
G9-18 (SI) or A3-22 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR