When the ignition switch is ON, the combination meter assembly monitors the state of the front passenger side seat and the front seat inner belt assembly LH and also whether the front passenger seat is occupied. If the front passenger side seat belt is not fastened, the seat belt warning light of the combination meter assembly blinks. If the seat belt is fastened, the warning light goes off.
The seat belt warning light on the combination meter assembly is used for both the driver side seat and front passenger side seat.
When replacing the combination meter assembly, make sure to replace it with a new one.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| P-Seatbelt Buckle SW | Front passenger seat belt buckle switch signal | ON or OFF | ON: Front passenger seat belt not fastened
OFF: Front passenger seat belt fastened |
Perform the inspection while sitting in the front passenger side seat. |
| Tester Display |
|---|
| P-Seatbelt Buckle SW |
| Result | Proceed to |
|---|---|
| ON or OFF is displayed on the GTS screen according to the front passenger side seat belt condition and front passenger seat condition (occupied or unoccupied) | A |
| ON or OFF is not displayed normally on the GTS screen according to the front passenger side seat belt condition (for LHD) | B |
| ON or OFF is not displayed normally on the GTS screen according to the front passenger side seat belt condition (for RHD) | C |
A
B
C
Disconnect the N17 front seat inner belt assembly LH connector.
Disconnect the G10 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N17-3 (+) - G10-4 (P/SB) | Always | Below 1 Ω |
| N17-2 (E) - Body ground | Always | Below 1 Ω |
| N17-3 (+) or G10-4 (P/SB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front seat inner belt assembly RH.
for Manual Seat:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Power Seat)>REMOVAL
for Bench Seat Type:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Bench Seat Type)>REMOVAL
Inspect the front seat inner belt assembly RH.
for Manual Seat:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Manual Seat)>INSPECTION
for Power Seat:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Power Seat)>INSPECTION
for Bench Seat Type:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Bench Seat Type)>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Manual Seat) | B |
| NG (for Power Seat) | C |
| NG (for Bench Seat Type) | D |
A
B
C
D
Remove the separate type front seat cushion pad (occupant detection sensor).
Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL
Inspect the separate type front seat cushion pad (occupant detection sensor).
Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N18 front seat inner belt assembly LH connector.
Disconnect the G10 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N18-3 (+) - G10-4 (P/SB) | Always | Below 1 Ω |
| N18-2 (E) - Body ground | Always | Below 1 Ω |
| N18-3 (+) or G10-4 (P/SB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front seat inner belt assembly LH.
for Manual Seat:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Power Seat)>REMOVAL
for Bench Seat Type:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Bench Seat Type)>REMOVAL
Inspect the front seat inner belt assembly LH.
for Manual Seat:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Manual Seat)>INSPECTION
for Power Seat:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Power Seat)>INSPECTION
for Bench Seat Type:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Bench Seat Type)>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Manual Seat) | B |
| NG (for Power Seat) | C |
| NG (for Bench Seat Type) | D |
A
B
C
D