Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL
RM33J0E _51 Engine / Hybrid System _038455 2TR-FE ENGINE MECHANICAL _0189929 REAR CRANKSHAFT OIL SEAL A

2TR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11381A 1.INSTALL REAR ENGINE OIL SEAL

a.
A346815N01
1.969,1.313 2.844,2.177 2.844,2.177 2.281,0.677 true 2.042,2.667 2.563,2.667 2.563,2.667 2.229,2.958 true 2.74,2.229 3.073,2.417 0.333,0.188 10 false SST 2.615,2.573 2.948,2.76 0.333,0.188 10 false SST

Apply a light coat of MP grease to the lip of a new rear engine oil seal.

NOTICE:
·

Do not allow foreign matter to contact the lip of the rear engine oil seal.

·

Do not allow MP grease to contact the dust seal.




b.

Using SST and a hammer, tap in the rear engine oil seal until its surface is flush with the rear engine oil seal retainer edge.

SST
09223-15030  
09950-70010  (09951-07150)

NOTICE:
·

Wipe off any extra grease from the crankshaft.

·

Do not tap in the rear engine oil seal at an angle.




Hide 13405 2.INSTALL FLYWHEEL SUB-ASSEMBLY

a.
A348628C01
1.563,1.917 1.75,2.104 0.188,0.188 10 false *a
*a Hold


Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.

Clean the bolt holes.


c.
A346812N01
1.396,0.875 1.51,1.052 0.115,0.177 10 true 2 2.615,1.25 2.729,1.427 0.115,0.177 10 true 1 1.615,1.719 1.729,1.896 0.115,0.177 10 true 3 2.5,0.552 2.615,0.729 0.115,0.177 10 true 4 1.375,1.281 1.49,1.458 0.115,0.177 10 true 5 2.656,0.917 2.771,1.094 0.115,0.177 10 true 6 1.615,0.552 1.729,0.729 0.115,0.177 10 true 7 2.438,1.583 2.552,1.76 0.115,0.177 10 true 8 2.052,1.781 2.167,1.958 0.115,0.177 10 true 9 2,0.385 2.198,0.563 0.198,0.177 10 true 10

Install the flywheel sub-assembly with the new 10 bolts and uniformly tighten the bolts in several steps in the sequence shown in the illustration.

Torque:
26.5 N*m (270 kgf*cm, 20 ft.*lbf)


d.

Mark the top of the bolts with paint.


e.

Tighten the 10 bolts 90° in the same sequence.


f.

Check that the paint marks are now at a 90° angle to the top.


Hide 31250 3.INSTALL CLUTCH DISC ASSEMBLY

Hide 31210 4.INSTALL CLUTCH COVER ASSEMBLY

Hide 31210 5.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY