Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › ENGINE UNIT
RM33J0E _51 Engine / Hybrid System _038455 2TR-FE ENGINE MECHANICAL _0189931 ENGINE UNIT A

2TR-FE ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


PROCEDURE

Hide 16268 1.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Install a new gasket and the No. 1 water by-pass pipe with the 2 nuts.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


Hide 16603 2.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 88431 3.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

NOTICE:

Install the No. 1 compressor mounting bracket exactly as described in the procedures below to properly secure and prevent damage to the fan and generator V belt.


a.
A346840

Temporarily install the No. 1 compressor mounting bracket with the 3 bolts.

HINT:

Temporarily install the No. 1 compressor mounting bracket with the 3 bolts so that the bracket can be moved by hand.



b.
A346841C01
1.219,3.406 1.427,3.604 0.208,0.198 10 false *a 2.115,4.313 2.323,4.51 0.208,0.198 10 false *b 0.729,2.531 0.917,2.729 0.188,0.198 10 false *c 2.969,3.406 3.177,3.604 0.208,0.198 10 false *a 0.5,0.354 0.656,0.552 0.156,0.198 10 true B
*a No Clearance
*b Push
*c Front


Push the No. 1 compressor mounting bracket toward the cylinder block as shown in the illustration and tighten bolt B.

Torque:
for bolt B : 45 N*m (459 kgf*cm, 33 ft.*lbf)

HINT:

Make sure there is no clearance between the cylinder block and No. 1 compressor mounting bracket as shown in the illustration.



c.
A346842C01
2.094,0.104 2.219,0.281 0.125,0.177 10 true 1 2.135,1.583 2.26,1.76 0.125,0.177 10 true 3 2.615,1.229 2.74,1.406 0.125,0.177 10 true 2 0.521,1.427 0.646,1.604 0.125,0.177 10 true 4
V100135

Bolt A
V100136

Bolt C


Uniformly tighten the 4 bolts in the order shown in the illustration.

Torque:
for bolt A : 45 N*m (459 kgf*cm, 33 ft.*lbf)
for bolt C : 24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 88440B 4.INSTALL IDLE PULLEY ASSEMBLY (w/ Air Conditioning System)

a.

Temporarily install the idle pulley assembly with the bolt.

NOTICE:

Do not use any tools.



b.

Tighten the bolt.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 25710 8.INSTALL AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)

Hide 17117B 9.INSTALL NO. 4 INTAKE PIPE (w/ Secondary Air Injection System)

Hide 17167 10.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/ Secondary Air Injection System)

Hide 17167 11.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o Secondary Air Injection System)

Hide 12311 12.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.

Install the front No. 1 engine mounting bracket RH with the 4 bolts.

Torque:
51 N*m (520 kgf*cm, 38 ft.*lbf)


Hide 12315 13.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.

Install the front No. 1 engine mounting bracket LH with the 4 bolts.

Torque:
51 N*m (520 kgf*cm, 38 ft.*lbf)


Hide 16261G 14.INSTALL NO. 1 WATER BY-PASS HOSE

a.

Connect the No. 1 water by-pass hose to the cylinder head sub-assembly, and slide the clamp to secure the hose.


Hide 15.INSTALL HEATER HOSE

a.

Connect the heater hose to the cylinder head sub-assembly and No. 1 water by-pass pipe, and slide the clamp to secure the hoses.


Hide 16.INSTALL ENGINE WIRE

a.
A346843C01
2.219,1.99 2.417,1.99 2.417,1.99 2.615,1.573 true 2.313,0.844 2.51,1.052 0.198,0.208 10 true *a 2.031,1.906 2.219,2.094 0.188,0.188 10 true *b 1.25,1.146 1.521,1.333 0.271,0.188 10 true 45° 0.594,1.146 0.865,1.333 0.271,0.188 10 true 45° 0.479,0.271 0.615,0.448 0.135,0.177 10 true A 1.875,0.063 2.01,0.24 0.135,0.177 10 true A 0.156,1.969 0.292,2.146 0.135,0.177 10 true B
*a INCORRECT
*b Do not Allow Wires to Overlap


Connect the engine wire (engine ground wire) to the rear side of the engine assembly with the 2 bolts so that it is within the specified range shown in the illustration.

Torque:
for bolt A : 25 N*m (255 kgf*cm, 18 ft.*lbf)


b.

Connect the engine wire to the rear side of the engine assembly with the bolt.

Torque:
for bolt B : 30 N*m (306 kgf*cm, 22 ft.*lbf)


c.

Connect the connectors and clamps of the engine wire.


Hide 12229 18.INSTALL PCV PIPE

a.

Install the PCV pipe with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Connect the PCV hose to the PCV valve sub-assembly and intake manifold.


Hide 23250 20.INSTALL FUEL DELIVERY PIPE WITH FUEL INJECTOR

Hide 22030 21.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY