Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY(for Single Cab)
RM33J0E _58 Vehicle Interior _040893 SEAT BELT _0192301 FRONT SEAT OUTER BELT ASSEMBLY(for Single Cab) A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY(for Single Cab)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 73220 1.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

a.
B416219C01
1.917,0.51 2.229,0.667 0.313,0.156 10 true *a 1.938,1.938 2.25,2.094 0.313,0.156 10 true *b 2.313,0.521 2.469,0.719 0.156,0.198 10 true 1 2.323,1.927 2.479,2.125 0.156,0.198 10 true 2
*a Bolt A
*b Bolt B


w/ Pretensioner:

i.

Attach the 2 guides and temporarily install the front seat outer belt assembly LH with the 2 bolts.


ii.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
for Bolt A : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
for Bolt B : 42 N*m (428 kgf*cm, 31 ft.*lbf)


iii.
B416220C01
0.99,0.427 1.26,0.271 false 1.313,0.177 1.625,0.375 0.313,0.198 10 true *1
*1 Locking Button


Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:

Securely lock the locking button.




b.

Connect the pretensioner connector and lock the locking button as shown in the illustration.


c.
B415715C01
2.031,0.563 2.344,0.76 0.313,0.198 10 true *a 1.042,1.927 1.333,2.146 0.292,0.219 10 true *b 2.24,0.573 2.396,0.771 0.156,0.198 10 true 1 0.823,1.927 1.031,2.146 0.208,0.219 10 true 2
*a Bolt A
*b Bolt B


w/o Pretensioner:

i.

Attach the 2 guides and temporarily install the front seat outer belt assembly LH with the 2 bolts.


ii.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
for Bolt A : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
for Bolt B : 42 N*m (428 kgf*cm, 31 ft.*lbf)



d.
B416217

Install the bolt and connect the shoulder anchor of the front seat outer belt assembly LH.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


e.

Check that the ELR locks.

NOTICE:

The check should be performed with the front seat outer belt assembly LH installed.


i.

With the belt assembly installed, check that the belt locks when it is pulled out quickly.



Hide 62514A 2.INSTALL LOWER QUARTER TRIM PANEL LH

Hide 73178A 3.INSTALL SEAT BELT ANCHOR COVER CAP

Hide 73220 4.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH (for Floor Anchor)

a.
B416216

Install the bolt and connect the floor anchor of the front seat outer belt assembly LH.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION