Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM33J0E _58 Vehicle Interior _038497 LIGHTING (INT) _0192388 LIGHTING SYSTEM U

LIGHTING (INT)  LIGHTING SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY ECU (w/ Automatic Light Contorl System)


E317657C01
0.594,3.865 0.927,4.104 0.333,0.24 1.99,3.865 2.323,4.104 0.333,0.24 3.458,3.865 3.792,4.104 0.333,0.24 4.844,3.865 5.177,4.104 0.333,0.24 6.198,3.865 6.531,4.104 0.333,0.24 0.594,5.063 0.927,5.302 0.333,0.24 1.969,5.063 2.302,5.302 0.333,0.24 3.333,5.063 3.667,5.302 0.333,0.24 4.729,5.063 5.063,5.302 0.333,0.24 6.198,5.063 6.531,5.302 0.333,0.24 0.604,6.448 0.938,6.688 0.333,0.24 1.938,6.448 2.271,6.688 0.333,0.24 3.375,6.448 3.708,6.688 0.333,0.24 4.833,6.448 5.167,6.688 0.333,0.24 6.208,6.438 6.542,6.677 0.333,0.24 3.344,7.708 3.677,7.948 0.333,0.24 0.104,0.052 0.417,0.292 0.313,0.24 12 false *1 0.75,0.938 1.063,1.135 0.313,0.198 10 false 2L 0.729,1.281 1.042,1.479 0.313,0.198 10 false 2M 0.74,1.667 1.052,1.865 0.313,0.198 10 false 2D 0.74,2.031 1.052,2.229 0.313,0.198 10 false 2K 0.729,2.375 1.042,2.573 0.313,0.198 10 false 2C 0.74,3.115 1.052,3.313 0.313,0.198 10 false 2A 1.281,3.104 1.594,3.302 0.313,0.198 10 false 2B 3.333,0.896 3.49,1.094 0.156,0.198 10 false A 6.375,0.583 6.688,0.781 0.313,0.198 10 false 2Q 6.396,0.927 6.708,1.125 0.313,0.198 10 false 2J 6.385,1.281 6.698,1.479 0.313,0.198 10 false 2P 6.385,1.656 6.698,1.854 0.313,0.198 10 false 2N 6.385,2 6.698,2.198 0.313,0.198 10 false 2G 6.396,2.375 6.708,2.573 0.313,0.198 10 false 2H 5.865,2.927 6.177,3.125 0.313,0.198 10 false 2F 6.375,2.99 6.688,3.188 0.313,0.198 10 false 2E 0.698,3.906 1.01,4.104 0.313,0.198 10 false 2L 2.063,3.906 2.375,4.104 0.313,0.198 10 false 2M 3.552,3.896 3.865,4.094 0.313,0.198 10 false 2D 4.917,3.906 5.229,4.104 0.313,0.198 10 false 2K 6.271,3.906 6.594,4.125 0.323,0.219 10 false 2C 0.667,5.094 0.979,5.292 0.313,0.198 10 false 2A 2.042,5.094 2.354,5.292 0.313,0.198 10 false 2B 3.406,5.104 3.719,5.302 0.313,0.198 10 false 2Q 4.823,5.094 5.135,5.292 0.313,0.198 10 false 2J 6.292,5.104 6.604,5.302 0.313,0.198 10 false 2P 0.688,6.479 1,6.677 0.313,0.198 10 false 2N 2.021,6.479 2.333,6.677 0.313,0.198 10 false 2G 3.458,6.479 3.771,6.677 0.313,0.198 10 false 2H 4.927,6.479 5.24,6.677 0.313,0.198 10 false 2F 6.292,6.469 6.604,6.667 0.313,0.198 10 false 2E 3.469,7.74 3.625,7.938 0.156,0.198 10 false A
*1 Instrument Panel Junction Block Assembly (for LHD) - -


E317657C07
0.594,3.865 0.927,4.104 0.333,0.24 1.99,3.865 2.323,4.104 0.333,0.24 3.458,3.865 3.792,4.104 0.333,0.24 4.844,3.865 5.177,4.104 0.333,0.24 6.198,3.865 6.531,4.104 0.333,0.24 0.594,5.063 0.927,5.302 0.333,0.24 1.969,5.063 2.302,5.302 0.333,0.24 3.333,5.063 3.667,5.302 0.333,0.24 4.729,5.063 5.063,5.302 0.333,0.24 6.198,5.063 6.531,5.302 0.333,0.24 0.604,6.448 0.938,6.688 0.333,0.24 1.938,6.448 2.271,6.688 0.333,0.24 3.375,6.448 3.708,6.688 0.333,0.24 4.833,6.448 5.167,6.688 0.333,0.24 6.208,6.438 6.542,6.677 0.333,0.24 3.344,7.708 3.677,7.948 0.333,0.24 0.104,0.052 0.417,0.292 0.313,0.24 12 false *1 0.75,0.938 1.063,1.135 0.313,0.198 10 false 2L 0.729,1.281 1.042,1.479 0.313,0.198 10 false 2M 0.74,1.667 1.052,1.865 0.313,0.198 10 false 2D 0.74,2.031 1.052,2.229 0.313,0.198 10 false 2K 0.729,2.375 1.042,2.573 0.313,0.198 10 false 2C 0.74,3.115 1.052,3.313 0.313,0.198 10 false 2R 1.281,3.104 1.594,3.302 0.313,0.198 10 false 2B 3.333,0.896 3.49,1.094 0.156,0.198 10 false A 6.375,0.583 6.688,0.781 0.313,0.198 10 false 2Q 6.396,0.927 6.708,1.125 0.313,0.198 10 false 2J 6.385,1.281 6.698,1.479 0.313,0.198 10 false 2P 6.385,1.656 6.698,1.854 0.313,0.198 10 false 2N 6.385,2 6.698,2.198 0.313,0.198 10 false 2G 6.396,2.375 6.708,2.573 0.313,0.198 10 false 2H 5.865,2.927 6.177,3.125 0.313,0.198 10 false 2F 6.375,2.99 6.688,3.188 0.313,0.198 10 false 2E 0.698,3.906 1.01,4.104 0.313,0.198 10 false 2L 2.063,3.906 2.375,4.104 0.313,0.198 10 false 2M 3.552,3.896 3.865,4.094 0.313,0.198 10 false 2D 4.917,3.906 5.229,4.104 0.313,0.198 10 false 2K 6.271,3.906 6.594,4.125 0.323,0.219 10 false 2C 0.667,5.094 0.979,5.292 0.313,0.198 10 false 2R 2.042,5.094 2.354,5.292 0.313,0.198 10 false 2B 3.406,5.104 3.719,5.302 0.313,0.198 10 false 2Q 4.823,5.094 5.135,5.292 0.313,0.198 10 false 2J 6.292,5.104 6.604,5.302 0.313,0.198 10 false 2P 0.688,6.479 1,6.677 0.313,0.198 10 false 2N 2.021,6.479 2.333,6.677 0.313,0.198 10 false 2G 3.458,6.479 3.771,6.677 0.313,0.198 10 false 2H 4.927,6.479 5.24,6.677 0.313,0.198 10 false 2F 6.292,6.469 6.604,6.667 0.313,0.198 10 false 2E 3.469,7.74 3.625,7.938 0.156,0.198 10 false A
*1 Instrument Panel Junction Block Assembly (for RHD) - -


E317658C07
2.24,3.344 2.625,3.583 0.385,0.24 4.563,3.344 4.948,3.583 0.385,0.24 0.125,0.073 0.438,0.365 0.313,0.292 12 false *1 5.76,1.531 6.219,1.729 0.458,0.198 10 false G28 5.76,2.021 6.219,2.219 0.458,0.198 10 false G27 2.292,3.375 2.75,3.573 0.458,0.198 10 false G28 4.635,3.375 5.094,3.573 0.458,0.198 10 false G27
*1 Body ECU - -


a.

Remove the body ECU from the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-6 (BECU) - Body ground - Battery power supply Always 11 to 14 V
A-7 (IG) - Body ground - IG power supply Ignition switch ON 11 to 14 V
A-1 (GND) - Body ground - Ground Always Below 1 Ω


c.

Install the body ECU to the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>INSTALLATION

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>INSTALLATION


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: w/o Smart Entry and Start System

*2: w/ Smart Entry and Start System

*3: w/ No. 1 Room Light Assembly

2Q-9 (ILE) - Body ground B - Body ground Illumination signal Map light and No. 1 room light*3 switch in DOOR position and map light assembly, No. 1 room light assembly*3 and transponder key coil*1 come on Below 1 V
Map light and No. 1 room light*3 switch in DOOR position and map light assembly, No. 1 room light assembly*3 and transponder key coil*1 go off 11 to 14 V
2L-4 (DCTY) - Body ground R - Body ground Driver side door courtesy light switch signal Driver side door open Below 1 V
Driver side door closed Pulse generation
G27-14 (PCTY) - Body ground LG - Body ground Front passenger side door courtesy light switch signal Front passenger side door open Below 1 V
Front passenger side door closed Pulse generation
G27-15 (LSWD) - Body ground R - Body ground Driver side door unlock detection switch signal Driver side door locked Pulse generation
Driver side door unlocked Below 1 V
G27-8 (KSW) - Body ground*1 G - Body ground Unlock warning switch assembly signal No key in ignition key cylinder Pulse generation
Key in ignition key cylinder Below 1 V
G27-9 (PRG) - Body ground*2 V - Body ground Signal output to certification ECU (smart key ECU assembly) Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed 11 to 14 V
Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed Pulse generation
2Q-2 (ACTY) - Body ground Y - Body ground Door courtesy switch signal All doors closed except driver door Pulse generation
Any door open except driver door Below 1 V
2P-13 (DOMR) - Body ground L - Body ground Battery saving control (interior light auto cut function) signal Battery saving control (interior light auto cut function) operating 11 to 14 V
Battery saving control (interior light auto cut function) not operating Below 1.7 V
G27-16 (RDA) - Body ground*2 W - Body ground Signal input from certification ECU (smart key ECU assembly) Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed 11 to 14 V
Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed Pulse generation
G27-2 (LSWP) - Body ground Y - Body ground Door unlock detection switch input (except front door) Except front door unlocked Below 1 V
Except front door locked Pulse generation



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)


a.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.

C332680E03
2.156,0.615 2.604,0.854 0.448,0.24 4.271,0.635 4.688,0.885 0.417,0.25 2.24,0.646 2.698,0.844 0.458,0.198 10 false G69 4.344,0.677 4.802,0.875 0.458,0.198 10 false G70


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G69-1 (+B) - Body ground P - Body ground Battery power supply Always 11 to 14 V
G69-10 (E) - Body ground BR - Body ground Ground Always Below 1 Ω


c.

Reconnect the G69 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G69-19 (SWIL) - G69-24 (AGND) G - SB Engine switch illumination drive output Engine switch illumination on 9 to 14 V
Engine switch illumination off Below 2 V
G69-9 (LSWP) - G69-10 (E) L - BR Door unlock detection switch input (except front door) Engine switch off, all doors closed, all doors unlocked and electrical key transmitter sub-assembly lock switch not pressed Below 1 V
Engine switch off, all doors closed, all doors unlocked and electrical key transmitter sub-assembly lock switch pressed 8.5 V or higher
G70-13 (RDA3) - G69-10 (E) W - BR Signal output to body ECU Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed 11 to 14 V
Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed Pulse generation
G70-36 (PRG3) - G69-10 (E) V - BR Signal input from body computer Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed 11 to 14 V
Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed Pulse generation
G69-21 (ACCD) - G69-10 (E) B - BR ACC signal Engine switch off → Engine switch on (ACC) 1 V or less → 8.5 V or higher
G69-20 (IG1D) - G69-10 (E) L - BR IG1 signal Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher



CHECK COMBINATION METER ASSEMBLY


E316846N02
0.875,0.448 1.208,0.635 0.333,0.188 2.76,0.458 3.094,0.646 0.333,0.188 5.604,0.417 5.958,0.615 0.354,0.198 0.906,0.469 1.313,0.667 0.406,0.198 10 false G10 2.844,0.469 3.156,0.667 0.313,0.198 10 false G9 5.656,0.438 5.969,0.635 0.313,0.198 10 false G11

a.

Measure the voltage, resistance and pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: w/o Immobiliser System

*2: except Single Cab

G10-8 (DM-1) - Body ground*1 W-B - Body ground Ground Always Below 1 Ω
G10-9 (PANEL) - Body ground*1 L - Body ground Illumination signal Map light and No. 1 room light*2 switch in DOOR position and map light assembly and No. 1 room light assembly*2 come on Below 1 V
Map light and No. 1 room light*2 switch in DOOR position and map light assembly and No. 1 room light assembly*2 go off 11 to 14 V
G10-10 (DM+1) - Body ground*1 B - Body ground Battery saving control (interior light auto cut function) signal Battery saving control (interior light auto cut function) operating 11 to 14 V
Battery saving control (interior light auto cut function) not operating Below 1.7 V
G10-12 (DOOR) - Body ground Y - Body ground Door courtesy switch signal Any door open except driver door Below 1 V
All doors closed except driver door Pulse generation
G10-15 (DCTY) - Body ground B - Body ground Driver side door courtesy light switch signal Driver side door open Below 1 V
Driver side door closed 11 to 14 V
G10-16 (PCTY) - Body ground G - Body ground Front passenger side door courtesy light switch signal Front passenger side door open Below 1 V
Front passenger side door closed 11 to 14 V
G10-17 (RLCY) - Body ground*2 V - Body ground Rear door LH courtesy light switch signal Rear door LH open Below 1 V
Rear door LH closed 11 to 14 V
G10-18 (RRCY) - Body ground*2 L - Body ground Rear door RH courtesy light switch signal Rear door RH open Below 1 V
Rear door RH closed 11 to 14 V