Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM33J0E _54 Brake _038477 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0192390 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1203  ECM Communication Circuit Malfunction  


DESCRIPTION

The rear differential lock identification signal is sent from the 4 wheel drive control ECU to the skid control ECU (brake actuator assembly) via the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1203 ECM Communication Circuit Malfunction Either of the following is detected:
1.

The rear differential lock identification signal sent from the 4 wheel drive control ECU does not match the information stored in the skid control ECU.

2.

No system information stored in the skid control ECU.

3.

Incorrect installation of the skid control ECU or 4 wheel drive control ECU.


·

4 wheel drive control ECU malfunction or 4 wheel drive control ECU with incorrect part number installed

·

Skid control ECU (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform Test Mode (Signal Check) to acquire the rear differential lock identification information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:

When DTC U0114 is output together with DTC C1203, inspect and repair the trouble areas indicated by DTC U0114 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>U0073


PROCEDURE

1.CHECK PART NUMBER (4 WHEEL DRIVE CONTROL ECU)
a.

Check that a proper 4 wheel drive control ECU is installed.


Result:
Proceed to
Proper 4 wheel drive control ECU is installed
Proper 4 wheel drive control ECU are not installed



Proper 4 wheel drive control ECU is installed

2.CHECK BRAKE ACTUATOR ASSEMBLY

Proper 4 wheel drive control ECU are not installed

REPLACE 4 WHEEL DRIVE CONTROL ECU

2.CHECK BRAKE ACTUATOR ASSEMBLY
a.

Check if the brake actuator assembly had been replaced before the DTC was recorded.


Result:
Proceed to
The brake actuator assembly is not replaced
The brake actuator assembly is replaced



The brake actuator assembly is not replaced

3.RECONFIRM DTC

The brake actuator assembly is replaced

4.PERFORM TEST MODE (SIGNAL CHECK)
3.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Proceed to
DTC C1203 is not output
DTC C1203 is output



DTC C1203 is not output

DTC C1203 is output

4.PERFORM TEST MODE (SIGNAL CHECK)
a.

Perform Test Mode (signal check).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

HINT:

After replacing the skid control ECU (brake actuator assembly), it is necessary to perform registration of rear differential lock identification information. Rear differential lock identification information is automatically acquired when the system enters test mode.



Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Proceed to
DTC C1203 is not output
DTC C1203 is output



DTC C1203 is not output

END

DTC C1203 is output