Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM33J0E _54 Brake _038477 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0192390 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1271  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1401  Front Speed Sensor RH Malfunction  C1402  Front Speed Sensor LH Malfunction  


DESCRIPTION

for 4WD and Pre-Runner:

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.

Skid control rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C235852C01
1.823,1.146 2.219,1.146 false 2.344,1.958 2.688,1.771 false 6.458,1 6.958,1.167 0.5,0.167 10 false 1.4 V 6.458,1.354 6.969,1.51 0.51,0.156 10 false 0.7 V 2.292,1.083 2.479,1.24 0.188,0.156 10 false *1 2.75,1.667 2.938,1.823 0.188,0.156 10 false *2 4.729,1.719 4.917,1.875 0.188,0.156 10 false *b 5.656,1.719 5.844,1.875 0.188,0.156 10 false *c 3.792,0.542 3.979,0.698 0.188,0.156 10 false *a
*1 Speed Sensor *2 Skid Control Rotor
*a Waveform (Reference):
Between Speed Sensor (-) and Body Ground
*b Low speed
*c High speed - -


for 2WD other than Pre-Runner:

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.

The speed sensor generates vehicle speed pulses based on the rotation of the skid control rotor. The skid control ECU (brake actuator assembly) detects the speed of each wheel using this vehicle speed pulse.

HINT:

When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C321040C01
1.083,0.844 1.75,0.844 false 1.104,1.5 1.667,1.76 false 0.917,0.771 1.135,0.979 0.219,0.208 10 false *1 0.927,1.385 1.146,1.594 0.219,0.208 10 false *2 3.615,0.604 3.833,0.813 0.219,0.208 10 false *a 4.531,1.708 4.75,1.917 0.219,0.208 10 false *b 5.458,1.708 5.677,1.917 0.219,0.208 10 false *c 6.313,0.958 6.781,1.167 0.469,0.208 10 false 1.4 V 6.313,1.333 6.781,1.542 0.469,0.208 10 false 0.7 V
*1 Speed Sensor *2 Skid Control Rotor
*a Waveform (Reference):
Between Speed Sensor (-) and Body Ground
*b Low speed
*c High speed - -



DTC No. Detection Item DTC Detection Condition Trouble Area
C1271 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor RH

·

Front skid control rotor RH (Front axle hub inner bearing RH)*1

·

Front skid control rotor RH*2

·

Sensor installation


C1272 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor LH

·

Front skid control rotor LH (Front axle hub inner bearing LH)*1

·

Front skid control rotor LH*2

·

Sensor installation


C1401 Front Speed Sensor RH Malfunction Either of the following is detected:
1.

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except both rear speed sensors are 0 km/h (0 mph))


·

Front speed sensor RH

·

Front skid control rotor RH (Front axle hub inner bearing RH)*1

·

Front skid control rotor RH*2

·

Sensor installation


C1402 Front Speed Sensor LH Malfunction Either of the following is detected:
1.

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except both rear speed sensors are 0 km/h (0 mph))


·

Front speed sensor LH

·

Front skid control rotor LH (Front axle hub inner bearing LH)*1

·

Front skid control rotor LH*2

·

Sensor installation



*1: for 4WD and Pre-Runner

*2: for 2WD other than Pre-Runner


PROCEDURE

1.CHECK FRONT SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C168336C15
1.994,1.633 2.181,1.795 0.186,0.161 10 *c 0.685,0.198 0.871,0.359 0.186,0.161 10 *a 2.296,0.198 2.482,0.359 0.186,0.161 10 *b
*a Normal
*b Abnormal
*c Clearance


Check the speed sensor installation.

for 2WD other than Pre-Runner: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 2WD)>INSTALLATION

for 4WD and Pre-Runner: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 4WD and Pre-Runner)>INSTALLATION

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

2.INSPECT FRONT SPEED SENSOR TIP

NG

2.INSPECT FRONT SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK (for 4WD and Pre-Runner)
OK (for 2WD other than Pre-Runner)
NG



OK (for 4WD and Pre-Runner)

3.INSPECT FRONT AXLE HUB INNER BEARING

OK (for 2WD other than Pre-Runner)

4.INSPECT FRONT SKID CONTROL ROTOR

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

3.INSPECT FRONT AXLE HUB INNER BEARING
a.

Remove the front axle hub inner bearing.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB(for 4WD and Pre-Runner)>REMOVAL


b.

Check the front skid control rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:
·

The front skid control rotor is incorporated into the front axle hub inner bearing.

·

If the skid control rotor needs to be replaced, replace it together with the front axle hub inner bearing.




c.

Reinstall the front speed sensor and the front axle hub inner bearing.

for the front speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 4WD and Pre-Runner)>INSTALLATION

for the front axle hub inner bearing: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB(for 4WD and Pre-Runner)>INSTALLATION


Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT AXLE HUB INNER BEARING

4.INSPECT FRONT SKID CONTROL ROTOR
a.

Remove the front skid control rotor.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB(for 2WD)>REMOVAL


b.

Check the front skid control rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE



c.

Reinstall the front speed sensor and the front skid control rotor.

for the front speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 2WD)>INSTALLATION

for the front skid control rotor: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB(for 2WD)>REMOVAL


Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SKID CONTROL ROTOR

5.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2

f.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
OK
NG




OK

NG

6.REPLACE FRONT SPEED SENSOR
6.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.


b.

Replace the front speed sensor.

for 2WD other than Pre-Runner: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 2WD)>REMOVAL

for 4WD and Pre-Runner: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 4WD and Pre-Runner)>REMOVAL

NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
NEXT



NEXT

7.RECONFIRM DTC
7.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1401 and C1402 are not output A
DTCs C1401 and/or C1402 are output (for 4WD and Pre-Runner) B
DTCs C1401 and/or C1402 are output (for 2WD other than Pre-Runner) C


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:

for 4WD and Pre-Runner:

·

The front skid control rotor is incorporated into the front axle hub inner bearing.

·

If the front skid control rotor needs to be replaced, replace it together with the front axle hub inner bearing.





A

END

B

C

REPLACE FRONT SKID CONTROL ROTOR