Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB(for 2WD)
RM33J0E _52 Drivetrain _038472 AXLE AND DIFFERENTIAL _0187675 FRONT AXLE HUB(for 2WD) A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB(for 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front axle hub removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Front wheel alignment adjustment
·

Clearing zero point calibration data

·

Yaw rate and acceleration sensor zero point calibration


·

DTCs are output

·

ABS warning light illumination

·

Slip indicator light illumination

·

VSC disable or malfunctioning


(Click here)


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 89543 2.DISCONNECT FRONT SPEED SENSOR LH

a.
C322631

Remove the bolt and harness clamp from the front absorber bracket.


b.

Remove the bolt and harness clamp from the front lower arm bracket.


c.
C322632

Remove the bolt and harness clamp from the steering knuckle LH.


d.

Remove the bolt and front speed sensor LH.

NOTICE:

Keep the sensor tip and sensor installation hole free from foreign matter.



Hide 3.DISCONNECT FRONT FLEXIBLE HOSE

Hide 47750 4.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY LH

Hide 47722 5.REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH

Hide 45047 7.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 48069 8.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C322830

Remove the 2 bolts and disconnect the front lower No. 1 suspension arm assembly LH from the steering knuckle LH.


Hide 48630 9.DISCONNECT FRONT UPPER SUSPENSION ARM ASSEMBLY LH

a.
C322809

Support the front axle hub assembly with a jack.


b.

Remove the clip and nut.


c.
C332697C01
2,1.167 2.917,1.167 true 2.969,1.094 3.427,1.292 0.458,0.198 10 false SST 0.458,0.885 0.833,1.083 0.375,0.198 10 true *b 2.583,1.917 2.958,2.115 0.375,0.198 10 true *a
*a Turn
*b Hold


Using SST, disconnect the steering knuckle LH from the front upper suspension arm assembly LH.

SST
09628-62011  


Hide 43442B 10.REMOVE KNUCKLE GREASE RETAINER CAP LH

a.

Secure the front axle hub sub-assembly LH between aluminum plates in a vise.


b.
C324890

Using a screwdriver and hammer, tap out the knuckle grease retainer cap LH.

NOTICE:

Be careful not to damage the steering knuckle LH.



Hide 43502H 11.REMOVE FRONT AXLE SHAFT NUT LH

a.
C324891N01
1.833,0.667 2.333,0.667 false 2.406,0.594 2.865,0.792 0.458,0.198 10 false SST

Using SST and a hammer, loosen the staked part of the front axle shaft nut LH.

SST
09930-00010  (09931-00010, 09931-00020)

NOTICE:
·

Completely loosen the staked part of the front axle shaft nut LH when removing it.

·

Do not damage the front axle hub sub-assembly LH.




b.
C324892

Using a 36 mm socket wrench, remove the front axle shaft nut LH.


Hide 43515 12.REMOVE FRONT SKID CONTROL ROTOR

a.
C324903

Remove the front skid control rotor.

NOTICE:

Take care not to scratch the serration of the front skid control rotor.



Hide 43502C 13.REMOVE FRONT AXLE HUB SUB-ASSEMBLY LH

a.
C332698C01
0.698,0.906 1.281,0.906 true 0.115,0.271 0.427,0.469 0.313,0.198 10 false *a 0.781,0.469 1.094,0.667 0.313,0.198 10 false *b 0.375,0.813 0.865,1.01 0.49,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the 3 front axle hub bolts.

SST
09650-17011  


b.
C324895N01
1.615,1.604 2.365,1.604 true 2.448,1.531 2.906,1.729 0.458,0.198 10 false SST

Install SST to the front axle hub assembly LH as shown in the illustration.

SST
09950-00020  


c.
C324896N01
2,0.927 1.927,0.281 1.927,0.281 2.448,0.49 false 1.604,0.146 2.063,0.344 0.458,0.198 10 false SST

Using SST and a press, remove the front axle hub assembly LH and front axle hub inner bearing (inner race) from the steering knuckle LH.

SST
09950-00020  
09950-60010  (09951-00400)


d.

Remove the 3 bolts and the dust cover.


Hide 43512E 14.REMOVE FRONT AXLE HUB HOLE SNAP RING LH

a.
C324897

Using a snap ring pliers, remove the front axle hub hole snap ring from the steering knuckle LH.


Hide 43502M 15.REMOVE FRONT INNER AXLE HUB BEARING LH

a.
C325399N01
1.542,1.323 0.521,0.885 0.521,0.885 1.042,0.823 true 0.198,0.802 0.656,1 0.458,0.198 10 false SST

Using SST, remove the front inner axle hub bearing LH (outer side inner race) from the front axle hub sub-assembly LH.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04020, 09955-04051, 09957-04010, 09958-04011)
09950-60010  (09951-00250)


b.

Remove the front inner axle hub bearing LH (inner side inner race) from the steering knuckle LH.


c.
C324898N01
0.771,1.115 0.885,0.656 0.885,0.656 0.688,0.771 false 0.906,0.469 1.292,0.688 0.385,0.219 10 false SST

Using SST and a hammer, tap out the front inner axle hub bearing LH (outer race) from the steering knuckle LH.

SST
09950-60020  (09951-00710)
09950-70010  (09951-07150)


Hide 43502F 16.REMOVE FRONT AXLE HUB OIL SEAL LH

a.

Using a screwdriver, pry out the front axle hub oil seal LH from the front axle hub sub-assembly LH.