Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM33J0E _54 Brake _038477 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0192391 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1413  Front Speed Sensor RH Output Malfunction  C1414  Front Speed Sensor LH Output Malfunction  


DESCRIPTION

Refer to DTCs C1401 and C1402.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1401

DTC No. Detection Item DTC Detection Condition Trouble Area
C1413 Front Speed Sensor RH Output Malfunction Either of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Front speed sensor RH

·

Front skid control rotor RH (Front axle hub inner bearing RH)*1

·

Front skid control rotor RH*2

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector


C1414 Front Speed Sensor LH Output Malfunction Either of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Front speed sensor LH

·

Front skid control rotor LH (Front axle hub inner bearing LH)*1

·

Front skid control rotor LH*2

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector



*1: for 4WD and Pre-Runner

*2: for 2WD other than Pre-Runner


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Normal or Error Normal Error: Momentary interruption
FL Speed Open Front speed sensor LH open detection Normal or Error Normal Error: Momentary interruption
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Speed Open
FL Speed Open
50003 105 200,201
OK:

Normal (There are no momentary interruptions.)


HINT:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FRONT SPEED SENSOR)

NG

4.CHECK FRONT SPEED SENSOR INSTALLATION
2.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2
g.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

4.CHECK FRONT SPEED SENSOR INSTALLATION
3.RECONFIRM DTC

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTCs C1413 and C1414 are not output
DTCs C1413 and/or C1414 are output



DTCs C1413 and C1414 are not output

DTCs C1413 and/or C1414 are output

4.CHECK FRONT SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C168336C15
1.994,1.633 2.181,1.795 0.186,0.161 10 *c 0.685,0.198 0.871,0.359 0.186,0.161 10 *a 2.296,0.198 2.482,0.359 0.186,0.161 10 *b
*a Normal
*b Abnormal
*c Clearance


Check the speed sensor installation.

for 2WD other than Pre-Runner: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 2WD)>INSTALLATION

for 4WD and Pre-Runner: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 4WD and Pre-Runner)>INSTALLATION

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

5.INSPECT FRONT SPEED SENSOR TIP

NG

5.INSPECT FRONT SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK (for 4WD and Pre-Runner)
OK (for 2WD other than Pre-Runner)
NG



OK (for 4WD and Pre-Runner)

6.INSPECT FRONT AXLE HUB INNER BEARING

OK (for 2WD other than Pre-Runner)

7.INSPECT FRONT SKID CONTROL ROTOR

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

6.INSPECT FRONT AXLE HUB INNER BEARING
a.

Remove the front axle hub inner bearing.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB(for 4WD and Pre-Runner)>REMOVAL


b.

Check the front skid control rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:
·

The front skid control rotor is incorporated into the front axle hub inner bearing.

·

If the skid control rotor needs to be replaced, replace it together with the front axle hub inner bearing.




c.

Reinstall the front speed sensor and the front axle hub inner bearing.

for the front speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 4WD and Pre-Runner)>INSTALLATION

for the front axle hub inner bearing: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB(for 4WD and Pre-Runner)>INSTALLATION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT AXLE HUB INNER BEARING

7.INSPECT FRONT SKID CONTROL ROTOR
a.

Remove the front skid control rotor.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB(for 2WD)>REMOVAL


b.

Check the front skid control rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



c.

Reinstall the front speed sensor and the front skid control rotor.

for the front speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 2WD)>INSTALLATION

for the front skid control rotor: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB(for 2WD)>INSTALLATION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SKID CONTROL ROTOR

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A4 skid control ECU (brake actuator assembly) connector and the A8 and/or A9 front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A4-31 (FR+) - A8-2 (FR+) Always Below 1 Ω
A4-30 (FR-) - A8-1 (FR-) Always Below 1 Ω
A4-31 (FR+) or A8-2 (FR+) - Body ground Always 10 kΩ or higher
A4-30 (FR-) or A8-1 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A4-18 (FL+) - A9-2 (FL+) Always Below 1 Ω
A4-17 (FL-) - A9-1 (FL-) Always Below 1 Ω
A4-18 (FL+) or A9-2 (FL+) - Body ground Always 10 kΩ or higher
A4-17 (FL-) or A9-1 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR OUTPUT)
a.
C190626C11
1.781,0.771 2.094,0.969 0.313,0.198 1.781,1.104 2.094,1.302 0.313,0.198 2.698,2.781 2.698,2.646 2.698,2.646 2.25,2.281 true 1.844,0.792 2.219,1.094 0.375,0.302 10 false A8 2.135,1.115 2.448,1.271 0.313,0.156 10 false *B 0.167,0.167 0.438,0.385 0.271,0.219 10 false *a 2.5,2.833 3.135,3.083 0.635,0.25 10 false FR+*A 2.521,3.073 3.167,3.333 0.646,0.26 10 false FL+*B 2.135,0.792 2.448,0.948 0.313,0.156 10 false *A 1.854,1.125 2.229,1.427 0.375,0.302 10 false A9
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)


Reconnect the A4 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
A8-2 (FR+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
A9-2 (FL+) - Body ground Ignition switch ON 8 to 14 V



Result:
Proceed to
OK
NG



OK

NG