Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2015.06–2016.07
RM33J0E _51 Engine / Hybrid System _038462 CRUISE CONTROL _0181542 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control main switch turn on with switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control the SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL functions.

WIRING DIAGRAM

C337659E01
3.688,3.219 4,3.417 0.313,0.198 10 false *1 4.26,2.75 4.573,2.948 0.313,0.198 10 false 4 4.229,2.969 4.542,3.167 0.313,0.198 10 false z4 4.229,2.063 4.542,2.26 0.313,0.198 10 false z4 4.26,1.833 4.573,2.031 0.313,0.198 10 false 3 3.115,2.844 3.427,3.042 0.313,0.198 10 false ECC 3.5,1.958 3.813,2.156 0.313,0.198 10 false 3 3.5,2.844 3.813,3.042 0.313,0.198 10 false 1 2.854,2.51 3.438,2.677 0.583,0.167 10 false ON-OFF 2.073,2.5 2.552,2.698 0.479,0.198 10 false +RES 1.302,2.5 1.781,2.667 0.479,0.167 10 false -SET 0.521,2.51 1.188,2.76 0.667,0.25 10 false CANCEL 0.917,3.5 1.146,3.698 0.229,0.198 10 false A 1,3.667 2.979,3.917 1.979,0.25 10 false Cruise Control Main Switch 0.25,4.365 2.25,4.615 2,0.25 10 false *1: Cruise Control Switch Wire 0.25,4.781 2.896,5.031 2.646,0.25 10 false *2: w/o Vehicle Stability Control System 0.25,5.198 2.979,5.448 2.729,0.25 10 false *3: w/ Vehicle Stability Control System 3.167,4.781 4.583,5.063 1.417,0.281 10 false *4: for 1KD-FTV 3.177,5.198 4.823,5.396 1.646,0.198 10 false *5: for 1GD-FTV 4.25,3.469 5.479,3.917 1.229,0.448 10 false Spiral Cable Sub-assembly*2 3.833,4.083 5.417,4.667 1.583,0.583 10 false Spiral with Sensor Cable Sub-assembly*3 5.229,2.958 5.542,3.156 0.313,0.198 10 false G4 5.281,2.74 5.594,2.938 0.313,0.198 10 false 2 5.229,2.063 5.542,2.26 0.313,0.198 10 false G4 5.271,1.833 5.583,2.031 0.313,0.198 10 false 1 4.771,1.948 5.083,2.146 0.313,0.198 10 false CCS 4.771,2.844 5.083,3.042 0.313,0.198 10 false ECC 5.625,1.115 5.938,1.313 0.313,0.198 10 false *4 5.583,0.885 5.896,1.083 0.313,0.198 10 false G84 5.635,0.646 5.948,0.844 0.313,0.198 10 false 21 5.958,0.885 6.271,1.083 0.313,0.198 10 false G86 6.01,0.646 6.323,0.844 0.313,0.198 10 false 26 6.01,1.115 6.323,1.313 0.313,0.198 10 false *5 6.344,0.885 6.656,1.083 0.313,0.198 10 false CCS 6.479,3.833 6.958,4.083 0.479,0.25 10 false ECM 3.115,1.958 3.427,2.156 0.313,0.198 10 false CCS

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control main switch signal (Main CPU) ON or OFF ON: Cruise control main switch on
OFF: Cruise control main switch off
-
Cancel Switch CANCEL switch signal ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -SET switch signal ON or OFF ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch +RES switch signal ON or OFF ON: +RES switch on
OFF: +RES switch off
-
Powertrain > Cruise Control > Data List
Tester Display
Main SW M-CPU
Cancel Switch
SET/COAST Switch
RES/ACC Switch
50003 237 16,23,22,21
OK:

When the cruise control main switch is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH
2.INSPECT CRUISE CONTROL MAIN SWITCH
a.

b.

Result:
Proceed to
OK
NG



OK

3.CHECK CRUISE CONTROL MAIN SWITCH

NG

3.CHECK CRUISE CONTROL MAIN SWITCH
a.
E178683C08
0.292,0.729 0.729,1.042 0.438,0.313 0.24,2.385 0.677,2.698 0.438,0.313 1.656,1.542 1.281,1.094 true 0.656,1.542 1.073,1.125 true 0.583,3.083 1,2.667 true 1.833,3.083 1.458,2.667 true 0.146,0.313 0.458,0.51 0.313,0.198 10 false *a 0.24,1.969 0.552,2.167 0.313,0.198 10 false *b 0.417,2.458 0.573,2.656 0.156,0.198 10 false A 0.438,0.823 0.75,1.021 0.313,0.198 10 false z4 1.573,1.583 2.031,1.781 0.458,0.198 10 false ECC 0.49,1.552 0.948,1.75 0.458,0.198 10 false CCS 1.708,3.115 2.167,3.313 0.458,0.198 10 false CCS 0.438,3.115 0.896,3.313 0.458,0.198 10 false ECC
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly (w/ Vehicle Stability Control System))
(to Spiral Cable Sub-assembly (w/o Vehicle Stability Control System))
*b Front view of wire harness connector
(to Cruise Control Main Switch)


Disconnect the spiral with sensor cable sub-assembly*1 or spiral cable sub-assembly*2 connector.

*1: w/ Vehicle Stability Control System

*2: w/o Vehicle Stability Control System



b.

Disconnect the cruise control main switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z4-3 (CCS) - A-3 (CCS) Always Below 1 Ω
z4-4 (ECC) - A-1 (ECC) Always Below 1 Ω
z4-3 (CCS) or A-3 (CCS) - Body ground Always 10 kΩ or higher
z4-4 (ECC) or A-1 (ECC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY OR SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE CRUISE CONTROL SWITCH WIRE

4.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY OR SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral with sensor cable sub-assembly*1 or spiral cable sub-assembly*2.

*1: w/ Vehicle Stability Control System

*2: w/o Vehicle Stability Control System


Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral with sensor cable sub-assembly*1 or spiral cable sub-assembly*2.

*1: w/ Vehicle Stability Control System

*2: w/o Vehicle Stability Control System


Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY OR SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY OR SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY OR SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

for 1KD-FTV

i.

Disconnect the G4 spiral with sensor cable sub-assembly*1 or spiral cable sub-assembly*2 connector.

*1: w/ Vehicle Stability Control System

*2: w/o Vehicle Stability Control System



ii.

Disconnect the G84 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-1 (CCS) - G84-21 (CCS) Always Below 1 Ω
G4-2 (ECC) - Body ground Always Below 1 Ω
G4-1 (CCS) or G84-21 (CCS) - Body ground Always 10 kΩ or higher




b.

for 1GD-FTV

i.

Disconnect the G4 spiral with sensor cable sub-assembly*1 or spiral cable sub-assembly*2 connector.

*1: w/ Vehicle Stability Control System

*2: w/o Vehicle Stability Control System



ii.

Disconnect the G86 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-1 (CCS) - G86-26 (CCS) Always Below 1 Ω
G4-2 (ECC) - Body ground Always Below 1 Ω
G4-1 (CCS) or G86-26 (CCS) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR