Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
RM33J0E _51 Engine / Hybrid System _038454 2TR-FE ENGINE CONTROL _0193317 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).
(a) Vehicle speed is 20 km/h (12.43 mph) or more.
(b) Engine speed is 1000 rpm or higher.
(c) STA signal is on.
·

Clutch start switch assembly

·

Ignition switch

·

ECM

·

Wire harness or connector


Comes on DTC stored

MONITOR STRATEGY

Required Sensors/Components (Main) Starter relay (ST NO. 1)
Clutch start switch assembly
Ignition switch assembly
Certification ECU
Required Sensors/Components (Related) Vehicle speed sensor
Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Vehicle speed 20 km/h (12.43 mph) or more
Engine speed 1000 rpm or higher

TYPICAL MALFUNCTION THRESHOLDS

Starter signal On

CONFIRMATION DRIVING PATTERN

A231469E24
1.229,1.979 1.656,2.198 0.427,0.219 10 Idling 0.396,2.26 1.604,2.583 1.208,0.323 10 Ignition Switch ON 1.063,0.865 1.635,1.073 0.573,0.208 10 24 km/h 2.396,2.854 3.083,3.167 0.688,0.313 10 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 20 seconds or more 2.01,2.333 2.302,2.552 0.292,0.219 10 [A] 2.615,2.125 2.823,2.302 0.208,0.177 10 [B] 4.063,0.458 4.292,0.625 0.229,0.167 10 [C] 4.885,3.333 5.115,3.5 0.229,0.167 10 [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

Idle the engine for 5 seconds or more [B].

8.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0617.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or UNKNOWN, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

A354231E05
5.771,1.135 6.229,1.333 0.458,0.198 10 false NSW 5.74,3.594 6.198,3.792 0.458,0.198 10 false STA 5.406,1.146 5.865,1.344 0.458,0.198 10 false C53 5.396,3.698 5.854,3.896 0.458,0.198 10 false C53 5.458,0.948 5.771,1.146 0.313,0.198 10 false 15 5.469,3.5 5.781,3.698 0.313,0.198 10 false 17 3.583,2.885 3.896,3.083 0.313,0.198 10 false B2 3.573,3.063 5.438,3.281 1.865,0.219 10 false Clutch Start Switch Assembly 4.573,2.635 4.729,2.833 0.156,0.198 10 false 2 3.698,2.625 3.854,2.823 0.156,0.198 10 false 1 1.583,1 2.042,1.198 0.458,0.198 10 false AM2 2.208,1 2.667,1.198 0.458,0.198 10 false ST2 2.552,1.01 2.708,1.208 0.156,0.198 10 false 2 1.406,1.031 1.563,1.229 0.156,0.198 10 false 4 1.323,1.417 1.635,1.615 0.313,0.198 10 false G1 1.313,1.573 4.979,1.771 3.667,0.198 10 false Ignition Switch Assembly 0.552,2.25 3.458,2.448 2.906,0.198 10 false STRG LOCK/AM2 NO. 1 1.385,3.875 2.615,4.073 1.229,0.198 10 false ST NO. 1 2.719,4.052 2.875,4.25 0.156,0.198 10 false 5 3.198,4.052 3.354,4.25 0.156,0.198 10 false 2 2.708,4.958 2.865,5.156 0.156,0.198 10 false 3 3.208,4.969 3.365,5.167 0.156,0.198 10 false 1 3.448,4.49 4.677,4.688 1.229,0.198 10 false ST NO. 1 0.531,4.75 1.604,4.948 1.073,0.198 10 false FL MAIN 1.979,5.427 2.438,5.625 0.458,0.198 10 false C32 1.281,5.844 1.594,6.042 0.313,0.198 10 false D3 2.302,5.417 2.458,5.615 0.156,0.198 10 false 1 1.375,5.635 1.531,5.833 0.156,0.198 10 false 1 0.646,6.708 1.719,6.906 1.073,0.198 10 false Battery 1.323,6.615 3.771,6.813 2.448,0.198 10 false Starter Assembly 0.125,0.115 4.104,0.313 3.979,0.198 10 false w/o Entry and Start System

A359910E01
0.26,0.083 4.083,0.281 3.823,0.198 10 false w/ Entry and Start System 0.188,2.156 1.708,2.854 1.521,0.698 10 false Certification ECU (Smart Key ECU Assembly) 1.333,0.875 1.646,1.073 0.313,0.198 10 false NE 1.167,1.313 1.781,1.51 0.615,0.198 10 false STAR 1.25,1.729 1.708,1.927 0.458,0.198 10 false STA 1.625,0.875 2.083,1.073 0.458,0.198 10 false G69 1.625,1.323 2.083,1.521 0.458,0.198 10 false G70 1.625,1.74 2.083,1.938 0.458,0.198 10 false G70 1.646,0.698 1.802,0.896 0.156,0.198 10 false 6 1.625,1.135 1.938,1.333 0.313,0.198 10 false 16 1.625,1.573 1.938,1.771 0.313,0.198 10 false 37 5.792,0.875 6.25,1.073 0.458,0.198 10 false NEO 5.417,0.875 5.875,1.073 0.458,0.198 10 false G46 5.5,0.688 5.813,0.885 0.313,0.198 10 false 16 5.427,1.333 5.885,1.531 0.458,0.198 10 false C53 5.521,1.146 5.833,1.344 0.313,0.198 10 false 15 3.521,2.969 3.677,3.167 0.156,0.198 10 false 1 4.406,3 4.563,3.198 0.156,0.198 10 false 2 3.354,3.302 3.667,3.5 0.313,0.198 10 false B2 3.292,3.479 5.25,3.719 1.958,0.24 10 false Clutch Start Switch Assembly 5.781,4.188 6.24,4.385 0.458,0.198 10 false STA 5.427,4.281 5.885,4.479 0.458,0.198 10 false C53 5.542,4.063 5.854,4.26 0.313,0.198 10 false 17 2.719,4.5 2.875,4.698 0.156,0.198 10 false 2 2.969,4.917 4.042,5.115 1.073,0.198 10 false ST NO.1 2.719,5.448 2.875,5.646 0.156,0.198 10 false 1 2.198,4.5 2.354,4.698 0.156,0.198 10 false 5 2.177,5.438 2.333,5.635 0.156,0.198 10 false 3 0.458,4.24 1.688,4.438 1.229,0.198 10 false ST NO. 1 0.448,5.25 1.521,5.448 1.073,0.198 10 false FL MAIN 1.073,6.104 1.385,6.302 0.313,0.198 10 false D3 1.75,5.885 2.208,6.083 0.458,0.198 10 false C32 0.583,6.792 1.656,6.99 1.073,0.198 10 false Battery 1.135,6.917 2.542,7.438 1.406,0.521 10 false Starter Assembly 6.125,5.479 6.583,5.677 0.458,0.198 10 false ECM 5.792,1.313 6.25,1.51 0.458,0.198 10 false NSW 2.115,5.875 2.271,6.073 0.156,0.198 10 false 1 1.156,5.896 1.313,6.094 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Result:
Condition Starter Signal Proceed to
Driving at 20 km/h (12.4 mph) or more OFF A
ON B




A

B

2.INSPECT CLUTCH START SWITCH ASSEMBLY
2.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (clutch start switch assembly - ST NO. 1 relay - ECM).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0617 is output A
DTC is not output B




A

B

END