"Manual cut off switch" refers to the airbag cutoff switch cylinder sub-assembly.
The airbag cutoff switch cylinder sub-assembly consists of the airbag sensor assembly and airbag cutoff switch cylinder sub-assembly.
The instrument panel passenger airbag assembly can be optionally deactivated via this circuit by turning the airbag cutoff switch cylinder sub-assembly to the "OFF" position.
If the instrument panel passenger airbag assembly is deactivated, the airbag cutoff switch cylinder sub-assembly comes on to inform the passengers.
DTC B1651/33 is stored when a malfunction is detected in the airbag cutoff switch cylinder sub-assembly circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1651/33 | Manual Cut off Switch Trouble | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the airbag cutoff switch cylinder sub-assembly circuit for 2 seconds. ·
An airbag cutoff switch cylinder sub-assembly malfunction. ·
An airbag sensor assembly malfunction. |
·
Instrument panel wire ·
Airbag cutoff switch cylinder sub-assembly ·
Airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
The 11 (MSW+) and 12 (MSW-) terminals in this circuit have an activation prevention mechanism. This mechanism can be used to check for an open circuit in the wire harness. In case of other checks (check for short, short to ground or short to B+), it is necessary to release this mechanism.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the airbag sensor assembly and airbag cutoff switch cylinder sub-assembly.
| Proceed to |
|---|
| The connectors are properly connected |
| The connectors are not properly connected |
The connectors are properly connected
The connectors are not properly connected
Disconnect the connectors from the airbag sensor assembly and airbag cutoff switch cylinder sub-assembly.
| *1 | Airbag Cutoff Switch Cylinder Sub-assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
Check that the connectors (on the airbag sensor assembly side and airbag cutoff switch cylinder sub-assembly side) are not damaged.
| Proceed to |
|---|
| The connectors are not deformed or damaged |
| The connectors are deformed or damaged |
The connectors are not deformed or damaged
The connectors are deformed or damaged
| *1 | Airbag Cutoff Switch Cylinder Sub-assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Connector C |
| *4 | Connector B |
| *5 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Airbag Cutoff Switch Cylinder Sub-assembly) |
| *b | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G43-2 (PMC+) - Body ground | Ignition switch ON | Below 1 V |
| G43-1 (PMC-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G43-2 (PMC+) - G43-1 (PMC-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G43-2 (PMC+) - G43-1 (PMC-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G43-2 (PMC+) - Body ground | Always | 1 MΩ or higher |
| G43-1 (PMC-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the airbag cutoff switch cylinder sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG CUT-OFF SWITCH>REMOVAL
Inspect the airbag cutoff switch cylinder sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG CUT-OFF SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Airbag Cutoff Switch Cylinder Sub-assembly |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the airbag sensor assembly and airbag cutoff switch cylinder sub-assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1651/33 is not output |
| DTC B1651/33 is output |
Codes other than DTC B1651/33 may be output at this time, but they are not related to this check.
DTC B1651/33 is not output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DIAGNOSIS SYSTEM
DTC B1651/33 is output