Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(for Type A)
RM33J0E _58 Vehicle Interior _038501 SUPPLEMENTAL RESTRAINT SYSTEMS _0193719 AIRBAG SYSTEM(for Type A) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Type A)  B1660/43  Passenger Airbag ON/OFF Indicator Circuit Malfunction  


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the airbag sensor assembly and passenger airbag ON/OFF indicator.

The passenger airbag ON/OFF indicator indicates the operation condition of the instrument panel passenger airbag assembly.

DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1660/43 Passenger Airbag ON/OFF Indicator Circuit Malfunction One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal, short circuit to ground signal or short circuit to B+ signal in the passenger airbag ON/OFF indicator circuit for 2 seconds.

·

A passenger airbag ON/OFF indicator malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

Harness and connector

·

Telltale light assembly

·

Airbag sensor assembly



WIRING DIAGRAM

C326160E04
1.115,0.948 1.729,1.146 0.615,0.198 10 false PAON 1.177,1.938 1.792,2.135 0.615,0.198 10 false P-AB 1.281,2.948 1.896,3.146 0.615,0.198 10 false IG+ 2.135,3.979 3.052,4.302 0.917,0.323 10 false from IG1 NO.4 Fuse 0.354,4.615 0.969,4.813 0.615,0.198 10 false G24 0.354,4.76 1.865,5.135 1.51,0.375 10 false Telltale Light Assembly 1.625,0.823 2.24,1.021 0.615,0.198 10 false 5 1.625,1.813 2.24,2.01 0.615,0.198 10 false 4 1.635,2.823 2.25,3.021 0.615,0.198 10 false 10 5.354,0.833 5.969,1.031 0.615,0.198 10 false 23 5.333,1.833 5.948,2.031 0.615,0.198 10 false 17 5.344,2.844 5.958,3.042 0.615,0.198 10 false 25 5.333,3.833 5.948,4.031 0.615,0.198 10 false 26 5.385,4.75 6.938,4.948 1.552,0.198 10 false Airbag Sensor Assembly 5.625,3.979 6.24,4.177 0.615,0.198 10 false E2 5.375,4.594 6.073,4.833 0.698,0.24 10 false G42 5.656,0.938 6.271,1.135 0.615,0.198 10 false PAON 5.656,1.948 6.271,2.146 0.615,0.198 10 false P-AB 5.635,2.948 6.25,3.146 0.615,0.198 10 false E1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Turn the ignition switch to ON.


b.

Check the passenger airbag ON/OFF indicator operation.

HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DIAGNOSIS SYSTEM


C280059E17
4.323,2.198 4.604,1.917 4.604,1.917 4.74,1.917 true 0.146,0.427 1.354,0.625 1.208,0.198 10 false Ignition Switch 0.125,1.302 1.51,2.052 1.385,0.75 10 false Passenger Airbag ON/OFF Indicator ("ON Indicator") 1.594,0.271 2.198,0.49 0.604,0.219 10 false ON 0.156,2.292 1.531,3.25 1.375,0.958 10 false Passenger Airbag ON/OFF Indicator ("OFF Indicator") 1.594,0.646 1.99,0.823 0.396,0.177 10 false Off 1.625,1.313 1.917,1.5 0.292,0.188 10 false On 1.646,1.688 2.042,1.865 0.396,0.177 10 false Off 1.625,2.333 1.917,2.521 0.292,0.188 10 false On 1.625,2.677 2.021,2.854 0.396,0.177 10 false Off 2.979,0.552 3.885,0.885 0.906,0.333 10 false Approximately 4 seconds 3.99,0.542 4.885,0.958 0.896,0.417 10 false Approximately 2 seconds 3.021,1.594 3.917,1.969 0.896,0.375 10 false Approximately 4 seconds 4.771,1.823 6.406,2.063 1.635,0.24 10 false Approximately 2 seconds 4.49,3.073 7.021,3.51 2.531,0.438 10 false ON/OFF condition depends on the front passenger detection results.


Result:
ON/OFF Indicator Illumination Proceed to
One or both indicators are always on A
Both indicators are always off B



A

2.CHECK CONNECTION OF CONNECTORS

B

7.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and telltale light assembly.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

3.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and telltale light assembly.


b.
C326674C01
0.688,1.271 1,1.427 0.313,0.156 10 false *1 2.542,1.542 2.854,1.698 0.313,0.156 10 false *2 1.51,0.5 1.823,0.656 0.313,0.156 10 false *3
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire


Check that the connectors (on the airbag sensor assembly side and telltale light assembly side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

The connectors are deformed or damaged

REPLACE INSTRUMENT PANEL WIRE

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
C301817

Connect the connector to the telltale light assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Check the passenger airbag ON/OFF indicator operation.


Result:
Proceed to
The passenger airbag ON/OFF indicator does not come on
The passenger airbag ON/OFF indicator comes on



The passenger airbag ON/OFF indicator does not come on

5.CHECK DTC

The passenger airbag ON/OFF indicator comes on

6.CHECK INSTRUMENT PANEL WIRE
5.CHECK DTC
a.
C326676C01
0.958,1.208 1.271,1.365 0.313,0.156 10 false *1 2.125,1.448 2.438,1.604 0.313,0.156 10 false *2
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1660/43 is not output
DTC B1660/43 is output


HINT:

Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.




DTC B1660/43 is not output

DTC B1660/43 is output

6.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the connector from the telltale light assembly.

C326677C03
2.458,0.646 2.823,0.896 0.365,0.25 5.021,0.656 5.385,0.906 0.365,0.25 5.74,1.51 5.74,1.333 true 3.24,1.417 3.604,1.115 true 4.135,1.427 3.771,1.104 true 5.271,1.333 5.771,0.865 true 6.51,1.302 6.146,1.031 true 0.479,1.135 0.792,1.292 0.313,0.156 10 false *1 1.688,1.302 2,1.458 0.313,0.156 10 false *2 6.552,0.417 6.865,0.573 0.313,0.156 10 false *4 5.708,1.542 6.021,1.698 0.313,0.156 10 false *5 0.667,0.729 0.823,0.885 0.156,0.156 10 false D 3.771,0.229 4.083,0.385 0.313,0.156 10 false *a 5.875,0.24 6.188,0.396 0.313,0.156 10 false *b 0.948,0.5 1.104,0.656 0.156,0.156 10 false C 1.219,0.5 1.375,0.656 0.156,0.156 10 false B 1.521,0.75 1.677,0.906 0.156,0.156 10 false A 2.521,0.698 2.844,0.865 0.323,0.167 10 false G24 5.063,0.698 5.385,0.865 0.323,0.167 10 false G42 4.063,1.458 4.604,1.677 0.542,0.219 10 false PAON 3.052,1.448 3.906,1.667 0.854,0.219 10 false P-AB 5.094,1.396 5.948,1.615 0.854,0.219 10 false P-AB 6.396,1.354 6.938,1.573 0.542,0.219 10 false PAON 4.688,0.49 5,0.646 0.313,0.156 10 false *3 1.052,0.958 1.365,1.115 0.313,0.156 10 false *6
*1 Telltale Light Assembly *2 Airbag Sensor Assembly
*3 Connector C *4 Connector B
*5 Service Wire *6 Instrument Panel Wire
*a Front view of wire harness connector
(to Telltale Light Assembly)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G24-4 (P-AB) - Body ground Ignition switch ON Below 1 V
G24-5 (PAON) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G24-4 (P-AB) - G24-5 (PAON) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G24-4 (P-AB) - G24-5 (PAON) Always 1 MΩ or higher
G24-4 (P-AB) - Body ground Always 1 MΩ or higher
G24-5 (PAON) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and telltale light assembly.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

8.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

8.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and telltale light assembly.


b.
C326674C01
0.688,1.271 1,1.427 0.313,0.156 10 false *1 2.542,1.542 2.854,1.698 0.313,0.156 10 false *2 1.51,0.5 1.823,0.656 0.313,0.156 10 false *3
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire


Check that the connectors (on the airbag sensor assembly side and telltale light assembly side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

9.CHECK INSTRUMENT PANEL WIRE

The connectors are deformed or damaged

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C326677C03
2.458,0.646 2.823,0.896 0.365,0.25 5.021,0.656 5.385,0.906 0.365,0.25 5.74,1.51 5.74,1.333 true 3.24,1.417 3.604,1.115 true 4.135,1.427 3.771,1.104 true 5.271,1.333 5.771,0.865 true 6.51,1.302 6.146,1.031 true 0.479,1.135 0.792,1.292 0.313,0.156 10 false *1 1.688,1.302 2,1.458 0.313,0.156 10 false *2 6.552,0.417 6.865,0.573 0.313,0.156 10 false *4 5.708,1.542 6.021,1.698 0.313,0.156 10 false *5 0.667,0.729 0.823,0.885 0.156,0.156 10 false D 3.771,0.229 4.083,0.385 0.313,0.156 10 false *a 5.875,0.24 6.188,0.396 0.313,0.156 10 false *b 0.948,0.5 1.104,0.656 0.156,0.156 10 false C 1.219,0.5 1.375,0.656 0.156,0.156 10 false B 1.521,0.75 1.677,0.906 0.156,0.156 10 false A 2.521,0.698 2.844,0.865 0.323,0.167 10 false G24 5.063,0.698 5.385,0.865 0.323,0.167 10 false G42 4.063,1.458 4.604,1.677 0.542,0.219 10 false PAON 3.052,1.448 3.906,1.667 0.854,0.219 10 false P-AB 5.094,1.396 5.948,1.615 0.854,0.219 10 false P-AB 6.396,1.354 6.938,1.573 0.542,0.219 10 false PAON 4.688,0.49 5,0.646 0.313,0.156 10 false *3 1.052,0.958 1.365,1.115 0.313,0.156 10 false *6
*1 Telltale Light Assembly *2 Airbag Sensor Assembly
*3 Connector C *4 Connector B
*5 Service Wire *6 Instrument Panel Wire
*a Front view of wire harness connector
(to Telltale Light Assembly)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G24-4 (P-AB) - Body ground Ignition switch ON Below 1 V
G24-5 (PAON) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G24-4 (P-AB) - G24-5 (PAON) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G24-4 (P-AB) - G24-5 (PAON) Always 1 MΩ or higher
G24-4 (P-AB) - Body ground Always 1 MΩ or higher
G24-5 (PAON) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)
a.
C326634C02
1.49,0.167 1.917,0.438 0.427,0.271 2.344,1.844 2.479,1.844 2.479,1.844 2.656,1.313 true 1.594,0.229 2.052,0.427 0.458,0.198 10 false G24 0.271,0.229 0.729,0.427 0.458,0.198 10 false *a 2.073,1.76 2.531,1.958 0.458,0.198 10 false IG+
*a Front view of wire harness connector
(to Telltale Light Assembly)


Connect the connectors to the airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G24-10 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE HARNESS AND CONNECTOR

11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
C213932C05
0.375,0.802 0.771,1.073 0.396,0.271 1.573,0.948 0.604,1.594 false 2.01,1.135 2.552,1.594 false 0.448,0.865 0.813,1.073 0.365,0.208 10 false G42 1.615,0.115 1.771,0.281 0.156,0.167 10 false *a 2.49,1.625 2.906,1.771 0.417,0.146 10 false PAON 0.365,1.625 0.76,1.771 0.396,0.146 10 false P-AB
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connector to the telltale light assembly.


d.

Disconnect the connectors from the airbag sensor assembly.


e.

Using a service wire, connect terminal 23 (PAON) and body ground.


f.

Using a service wire, connect terminal 17 (P-AB) and body ground.


g.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


h.

Turn the ignition switch to ON.


i.

Check the indicator according to the table below.

OK:
Tester Connection Switch Condition Passenger Airbag ON/OFF Indicator
G42-23 (PAON) - Body ground Ignition switch ON "ON" comes on
G42-17 (P-AB) - Body ground Ignition switch ON "OFF" comes on



j.

Disconnect the service wire from the airbag sensor assembly.


Result:
Proceed to
OK
NG



OK

12.CHECK DTC

NG

12.CHECK DTC
a.
C326676C01
0.958,1.208 1.271,1.365 0.313,0.156 10 false *1 2.125,1.448 2.438,1.604 0.313,0.156 10 false *2
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connectors to the airbag sensor assembly.


d.

Connect the cable to the negative (-) battery terminal and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1660/43 is not output
DTC B1660/43 is output


HINT:

Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.




DTC B1660/43 is not output

DTC B1660/43 is output