Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM33J0E _58 Vehicle Interior _038496 THEFT DETERRENT / KEYLESS ENTRY _0194112 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit that goes from the ACC output terminal of the certification ECU (smart key ECU assembly) to the ACC relay.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2274 ACC Monitor Malfunction Malfunction in the ACC relay circuit in the certification ECU (smart key ECU assembly) or in the external circuit (1-trip detection logic*1).
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

SMART fuse

·

ACC relay (Instrument panel junction block assembly)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off.
HINT:

To turn the engine switch on (ACC), carry an electrical key transmitter sub-assembly and press the engine switch with the shift lever in P*2 and the brake pedal*2 or clutch pedal*3 released.



*1: Only detected while a malfunction is present.

*2: for Automatic Transmission

*3: for Manual Transmission


DTC Detection Condition Combination Table
Vehicle Condition
Pattern 1 Pattern 2
Malfunction Statu Malfunction in the ACC relay circuit in the certification ECU (smart key ECU assembly) ○ -
Malfunction in the ACC relay circuit in the external circuit - ○
Detection Time - -
Trip Count 1-trip 1-trip

HINT:

If the conditions match either of these patterns, a DTC will be output.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction due to the relay being stuck on, the ACC relay does not turn off even though the engine switch is off.

·

If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the engine switch is on (ACC).


HINT:

The engine switch can be turned on (IG) and the engine can be started.


-

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2274
Power Source Control
·

ACC Relay Monitor


Starting Control
·

Ignition


-

WIRING DIAGRAM

C325658E03
0.156,1.094 1.021,1.333 0.865,0.24 10 false from Battery 1.51,1.271 2.104,1.479 0.594,0.208 10 false SMART 2.26,2.906 2.719,3.104 0.458,0.198 10 false G69 2.271,3.063 3.792,3.438 1.521,0.375 10 false Certification ECU (Smart Key ECU Assembly) 4.146,2.438 6.823,2.646 2.677,0.208 10 false Instrument Panel Junction Block Assembly 2.438,1.083 2.75,1.281 0.313,0.198 10 false +B 2.219,1 2.375,1.198 0.156,0.198 10 false 1 2.448,2.26 2.604,2.458 0.156,0.198 10 false E 2.167,2.135 2.479,2.333 0.313,0.198 10 false 10 3.094,1.656 3.708,1.854 0.615,0.198 10 false ACCD 3.573,1.646 3.885,1.844 0.313,0.198 10 false 21 4.271,1.76 4.583,1.958 0.313,0.198 10 false 2E 4.323,1.573 4.479,1.771 0.156,0.198 10 false 2 4.281,1.344 4.594,1.542 0.313,0.198 10 false 2A 4.323,1.146 4.479,1.344 0.156,0.198 10 false 1 4.844,2.063 5.302,2.26 0.458,0.198 10 false ACC 5.344,1.479 6.438,1.688 1.094,0.208 10 false SFT LOCK-ACC 6.427,1.344 6.74,1.542 0.313,0.198 10 false 2P 6.438,1.76 6.75,1.958 0.313,0.198 10 false 2J 6.458,1.573 6.615,1.771 0.156,0.198 10 false 5 6.458,1.156 6.615,1.354 0.156,0.198 10 false 5 2.573,1.656 2.885,1.854 0.313,0.198 10 false IC 2.917,1.198 3.229,1.396 0.313,0.198 10 false +B 0.125,0.063 0.802,0.302 0.677,0.24 12 false for LHD:

C325658E02
0.156,1.094 1.021,1.333 0.865,0.24 10 false from Battery 1.51,1.271 2.104,1.479 0.594,0.208 10 false SMART 2.26,2.906 2.719,3.104 0.458,0.198 10 false G69 2.271,3.063 3.792,3.438 1.521,0.375 10 false Certification ECU (Smart Key ECU Assembly) 4.146,2.438 6.823,2.646 2.677,0.208 10 false Instrument Panel Junction Block Assembly 2.438,1.083 2.75,1.281 0.313,0.198 10 false +B 2.219,1 2.375,1.198 0.156,0.198 10 false 1 2.448,2.26 2.604,2.458 0.156,0.198 10 false E 2.167,2.135 2.479,2.333 0.313,0.198 10 false 10 3.094,1.656 3.708,1.854 0.615,0.198 10 false ACCD 3.573,1.646 3.885,1.844 0.313,0.198 10 false 21 4.271,1.76 4.583,1.958 0.313,0.198 10 false 2E 4.323,1.573 4.479,1.771 0.156,0.198 10 false 2 4.281,1.344 4.594,1.542 0.313,0.198 10 false 2R 4.323,1.146 4.479,1.344 0.156,0.198 10 false 1 4.844,2.063 5.302,2.26 0.458,0.198 10 false ACC 5.344,1.479 6.438,1.688 1.094,0.208 10 false SFT LOCK-ACC 6.427,1.344 6.74,1.542 0.313,0.198 10 false 2P 6.438,1.76 6.75,1.958 0.313,0.198 10 false 2J 6.458,1.573 6.615,1.771 0.156,0.198 10 false 5 6.458,1.156 6.615,1.354 0.156,0.198 10 false 5 2.573,1.656 2.885,1.854 0.313,0.198 10 false IC 2.917,1.198 3.229,1.396 0.313,0.198 10 false +B 0.104,0.052 0.844,0.271 0.74,0.219 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 2E and 2J instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-21 (ACCD) - 2E-2 Always Below 1 Ω
2J-5 - Body ground Always Below 1 Ω
G69-21 (ACCD) or 2E-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.

b.

Remove the body ECU from the instrument panel junction block assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

B342624C10
1.031,0.333 1.417,0.583 0.385,0.25 2.615,0.333 3,0.583 0.385,0.25 4.167,0.333 4.552,0.583 0.385,0.25 5.75,0.333 6.135,0.583 0.385,0.25 1.031,0.063 1.417,0.292 0.385,0.229 0.125,0.063 0.438,0.219 0.313,0.156 10 false *a 1.146,0.094 1.458,0.292 0.313,0.198 10 false 2A 2.729,0.365 3.042,0.563 0.313,0.198 10 false 2P 4.281,0.365 4.594,0.563 0.313,0.198 10 false 2E 5.865,0.365 6.177,0.563 0.313,0.198 10 false 2J 1.135,0.385 1.448,0.583 0.313,0.198 10 false 2R 1.469,0.083 1.771,0.281 0.302,0.198 10 false (*A) 1.469,0.354 1.771,0.563 0.302,0.208 10 false (*B)
*A for LHD *B for RHD
*a Component without harness connected (Instrument Panel Junction Block Assembly) - -


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
2A-1 - 2P-5 Battery voltage not applied to terminals 2E-2 and 2J-5 10 kΩ or higher
Battery voltage applied to terminals 2E-2 and 2J-5 Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
2R-1 - 2P-5 Battery voltage not applied to terminals 2E-2 and 2J-5 10 kΩ or higher
Battery voltage applied to terminals 2E-2 and 2J-5 Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the G69 certification ECU (smart key ECU assembly) connector.


b.

Install the instrument panel junction block assembly.


c.

Measure the voltage according to the value(s) in the table below.

C332681C02
1.854,0.479 2.313,0.74 0.458,0.26 1.563,2.406 1.771,2.406 1.771,2.406 1.885,1.625 true 0.219,0.115 0.531,0.313 0.313,0.198 10 false *a 1.958,0.531 2.417,0.729 0.458,0.198 10 false G69 1.167,2.333 1.781,2.531 0.615,0.198 10 false ACCD
*a Component with harness connected (Certification ECU (Smart Key ECU Assembly)) - -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
G69-21 (ACCD) - Body ground Engine switch off → Engine switch on (ACC) 1 V or less → 8.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)