Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM
RM33J0E _51 Engine / Hybrid System _038446 2KD-FTV ENGINE CONTROL _0195892 ECD SYSTEM J

2KD-FTV ENGINE CONTROL  ECD SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A206916E63
4.375,1.25 6.219,1.594 1.844,0.344 10 false 5 V Constant Voltage Circuit 5.354,2.094 6.365,2.438 1.01,0.344 10 false Microprocessor 1.615,1.135 2.792,1.396 1.177,0.26 10 false from EFI-B Fuse 0.906,1.479 2.854,1.76 1.948,0.281 10 false from EFI-MAIN NO. 1 Relay 2.906,1.031 3.302,1.219 0.396,0.188 10 false BATT 0.354,2.229 2.615,2.802 2.26,0.573 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (sensors which have ICs) 0.365,2.969 2.625,3.438 2.26,0.469 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.063,3.125 4.323,3.333 0.26,0.208 10 false R 3,1.375 3.281,1.573 0.281,0.198 10 false +B 3.177,2.25 3.542,2.479 0.365,0.229 10 false VC 4.885,3.375 5.333,3.604 0.448,0.229 10 false ECM

When the VC circuit has a short circuit, the CPU in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

A303421E08
5.427,8.438 5.885,8.635 0.458,0.198 10 false ECM 2.167,2.26 2.542,2.469 0.375,0.208 10 false VTA 2.25,2.635 2.563,2.833 0.313,0.198 10 false VC 2.271,3.052 2.563,3.25 0.292,0.198 10 false E2 2.615,2.146 3.073,2.344 0.458,0.198 10 false 3 2.615,2.531 3.073,2.729 0.458,0.198 10 false 1 2.625,2.938 3.083,3.135 0.458,0.198 10 false 2 4.698,2.24 5.021,2.427 0.323,0.188 10 false C56 4.698,2.646 5.021,2.833 0.323,0.188 10 false C55 4.708,3.042 5.031,3.229 0.323,0.188 10 false C55 4.75,2.052 4.99,2.229 0.24,0.177 10 false 29 4.75,2.469 4.99,2.646 0.24,0.177 10 false 18 4.75,2.865 4.99,3.042 0.24,0.177 10 false 28 5.083,2.25 5.542,2.448 0.458,0.198 10 false VLU 5.094,2.646 5.552,2.844 0.458,0.198 10 false VC 5.083,3.063 5.542,3.26 0.458,0.198 10 false E2 1.208,3.625 3.031,3.896 1.823,0.271 10 false Throttle Body Assembly 1.188,3.448 1.646,3.646 0.458,0.198 10 false C76 0.917,7.042 1.375,7.24 0.458,0.198 10 false C89 0.906,7.208 3.188,7.448 2.281,0.24 10 false Manifold Absolute Pressure Sensor 2.271,5.823 2.563,6 0.292,0.177 10 false VC 2.25,6.208 2.563,6.438 0.313,0.229 10 false PIM 2.365,6.625 2.677,6.854 0.313,0.229 10 false E 4.76,6.031 5.073,6.229 0.313,0.198 10 false 28 4.698,6.208 5.01,6.406 0.313,0.198 10 false C56 5.063,6.219 5.375,6.417 0.313,0.198 10 false PIM 4.01,8.406 4.323,8.635 0.313,0.229 10 false B 3.208,8.396 3.521,8.625 0.313,0.229 10 false A 2.604,5.719 3.063,5.917 0.458,0.198 10 false 3 2.604,6.115 3.063,6.313 0.458,0.198 10 false 2 2.604,6.51 3.063,6.708 0.458,0.198 10 false 1

A355991E02
1.271,4 2.667,4.229 1.396,0.229 10 false Fuel Pressure Sensor 1.271,3.813 2.667,4.042 1.396,0.229 10 false C120 3.323,0.5 3.635,0.667 0.313,0.167 10 false A 3.885,0.5 4.198,0.667 0.313,0.167 10 false B 4.677,2.292 5.073,2.542 0.396,0.25 10 false C55 2.24,1.917 2.635,2.167 0.396,0.25 10 false VC 2.24,2.302 2.635,2.552 0.396,0.25 10 false PR 2.156,2.698 2.552,2.948 0.396,0.25 10 false E2S 2.146,3.094 2.542,3.344 0.396,0.25 10 false PR2 2.135,3.51 2.531,3.76 0.396,0.25 10 false VCS 2.583,1.385 2.979,1.635 0.396,0.25 10 false 4 2.583,1.771 2.979,2.021 0.396,0.25 10 false 6 2.583,2.167 2.917,2.333 0.333,0.167 10 false 5 2.583,2.573 3,2.74 0.417,0.167 10 false 3 2.583,2.979 2.75,3.146 0.167,0.167 10 false 2 2.583,3.375 2.833,3.573 0.25,0.198 10 false 1 2.25,1.5 2.646,1.75 0.396,0.25 10 false E2 4.667,2.698 5.063,2.948 0.396,0.25 10 false C56 4.667,3.094 5.063,3.344 0.396,0.25 10 false C55 4.667,3.5 5.063,3.75 0.396,0.25 10 false C56 5.083,3.5 5.479,3.75 0.396,0.25 10 false VCS 5.083,3.104 5.479,3.354 0.396,0.25 10 false PCR2 5.083,2.708 5.479,2.958 0.396,0.25 10 false E2S 5.083,2.292 5.479,2.542 0.396,0.25 10 false PCR1 4.74,2.51 5.073,2.677 0.333,0.167 10 false 1 4.719,2.094 5.052,2.26 0.333,0.167 10 false 26 4.719,2.917 5.052,3.083 0.333,0.167 10 false 33 4.75,3.323 4.917,3.49 0.167,0.167 10 false 2 1.271,7.906 3.583,8.156 2.313,0.25 10 false Accelerator Pedal Position Sensor 1.271,7.719 1.583,7.948 0.313,0.229 10 false A41 2.583,6.448 2.833,6.646 0.25,0.198 10 false 1 2.594,6.865 3.01,7.031 0.417,0.167 10 false 3 2.594,7.26 2.76,7.427 0.167,0.167 10 false 2 2.583,6.063 2.917,6.229 0.333,0.167 10 false 5 2.583,5.656 2.979,5.906 0.396,0.25 10 false 6 2.583,5.25 2.979,5.5 0.396,0.25 10 false 4 4.667,5.396 5.063,5.646 0.396,0.25 10 false G84 4.667,5.792 5.063,6.042 0.396,0.25 10 false G84 4.667,6.188 5.063,6.438 0.396,0.25 10 false G84 4.667,6.594 5.063,6.844 0.396,0.25 10 false G84 4.667,6.99 5.063,7.24 0.396,0.25 10 false G84 4.667,7.396 5.063,7.646 0.396,0.25 10 false G84 4.719,5.188 5.052,5.354 0.333,0.167 10 false 26 4.719,5.615 5.052,5.781 0.333,0.167 10 false 22 4.719,6.01 5.052,6.177 0.333,0.167 10 false 28 4.719,6.417 5.052,6.583 0.333,0.167 10 false 27 4.719,7.208 5.052,7.375 0.333,0.167 10 false 29 4.719,6.813 5.052,6.979 0.333,0.167 10 false 23 5.031,5.406 5.531,5.656 0.5,0.25 10 false VCPA 2.031,5.406 2.531,5.656 0.5,0.25 10 false VCPA 2.135,5.792 2.635,6.042 0.5,0.25 10 false VPA 5.042,5.802 5.542,6.052 0.5,0.25 10 false VPA 2.063,6.594 2.563,6.844 0.5,0.25 10 false VCP2 5.031,6.188 5.531,6.438 0.5,0.25 10 false EPA 5.031,6.594 5.531,6.844 0.5,0.25 10 false VCP2 2.135,6.177 2.635,6.427 0.5,0.25 10 false EPA 2.063,7 2.563,7.25 0.5,0.25 10 false VPA2 5.031,7 5.531,7.25 0.5,0.25 10 false VPA2 2.083,7.406 2.583,7.656 0.5,0.25 10 false EPA2 5.021,7.406 5.521,7.656 0.5,0.25 10 false EPA2 5.427,8.5 5.927,8.75 0.5,0.25 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and GTS on.


c.

Check the communication between the GTS and ECM.

Result:
Condition Proceed to
Communication is not possible A
Communication is possible B




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

B

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.

Turn the ignition switch to ON.


b.
A080463C74
1.24,0.198 1.615,0.458 0.375,0.26 2.438,0.208 2.813,0.469 0.375,0.26 1.177,0.781 0.927,1.49 true 3,0.792 3.01,1.531 true 1.281,0.25 1.563,0.448 0.281,0.198 10 false C56 2.5,0.26 2.896,0.458 0.396,0.198 10 false G84 0.719,1.531 1.167,1.729 0.448,0.198 10 false 7 (E1) 2.854,1.542 3.313,1.74 0.458,0.198 10 false 1 (+B) 0.042,0.094 0.271,0.271 0.229,0.177 10 false *a
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G84-1 (+B) - C56-7 (E1) IG ON 11 to 14 V



Result:
Proceed to
OK
NG


HINT:

If the result is not as specified, since current is not flowing to the +B terminals of the ECM, the system may not be started.



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.


Result:
Result Proceed to
Communication is possible A
Communication is not possible B



e.

Reconnect the throttle position sensor connector.



A

4.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

REPLACE DIESEL THROTTLE BODY ASSEMBLY

4.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.


Result:
Result Proceed to
Communication is possible A
Communication is not possible B



e.

Reconnect the manifold absolute pressure sensor connector.



A

5.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

B

5.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.Check the MIL.

HINT:

It can be checked using the "Engine" item of the Data List.


Result:
Result Proceed to
Communication is possible A
Communication is not possible B



e.

Reconnect the accelerator position sensor connector.



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR)

B

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

6.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR)
a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.


Result:
Result Proceed to
Communication is possible A
Communication is not possible B



e.

Reconnect the fuel pressure sensor connector.



A

7.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

B

REPLACE COMMON RAIL ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the throttle position sensor connector.


b.

Disconnect the manifold absolute pressure sensor connector.


c.

Disconnect the fuel pressure sensor connector.


d.

Disconnect the accelerator pedal position sensor connector.


e.

Disconnect the ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C55-18 (VC) - Body ground Always 10 kΩ or higher
C56-2 (VCS) - Body ground Always 10 kΩ or higher
G84-26 (VCPA) - Body ground Always 10 kΩ or higher
G84-27 (VCP2) - Body ground Always 10 kΩ or higher



g.

Reconnect the throttle position sensor connector.


h.

Reconnect the manifold absolute pressure sensor connector.


i.

Reconnect the fuel pressure sensor connector.


j.

Reconnect the accelerator pedal position sensor connector.


k.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR