Home › Engine / Hybrid System › 1KD-FTV FUEL › COMMON RAIL
RM33J0E _51 Engine / Hybrid System _038430 1KD-FTV FUEL _0196042 COMMON RAIL A

1KD-FTV FUEL  COMMON RAIL  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·
A339769

To prevent burns, do not remove the oil pan drain plug and oil filter sub-assembly while the engine is hot.


·
A343691

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

When replacing the common rail assembly, do not remove the foreign object mixing prevention caps of the common rail assembly until just before the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly are connected to the common rail assembly.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 17940D 3.REMOVE INTERCOOLER ASSEMBLY

Hide 51410 4.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442 5.REMOVE NO. 2 ENGINE UNDER COVER

Hide 15601 8.REMOVE OIL FILTER SUB-ASSEMBLY

Hide 23701 9.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

Hide 23704 10.REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

Hide 23770 11.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 11452 12.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 23804C 13.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 23810A 14.REMOVE COMMON RAIL ASSEMBLY

a.

Disconnect the connector from the pressure discharge valve.


b.

Disconnect the connector from the fuel pressure sensor connector.


c.
A347283

Remove the 2 bolts, common rail assembly from the cylinder head sub-assembly.

NOTICE:

Do not remove the pressure discharge valve or fuel pressure sensor from the common rail assembly.



Hide 17136 15.REMOVE NO. 2 INTAKE MANIFOLD INSULATOR

a.
A347284

Remove the No. 2 intake manifold insulator from the cylinder head sub-assembly.